Hi Rob,
On 19/09/24 02:14, Rob Herring wrote:
On Wed, Sep 18, 2024 at 11:29:28AM +1200, Chris Packham wrote:
Add dtschema for the I2C controller on the RTL9300 SoC. The I2C
controllers on this SoC are part of the "switch" block which is
represented here as a syscon node. The SCL pins are dependent on the I2C
controller (GPIO8 for the first controller, GPIO 17 for the second). The
SDA pins can be assigned to either one of the I2C controllers (but not
both).
Signed-off-by: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
---
Notes:
This does hit generate the following dt_binding_check warning
realtek,rtl9300-i2c.example.dts:22.19-30.13: Warning (unit_address_vs_reg): /example-0/switch@1b000000/i2c@36c: node has a unit name, but no reg or ranges property
Which is totally correct. I haven't given this thing a reg property
because I'm using an offset from the parent syscon node. I'm also not
calling the first offset "offset" but I don't think that'd help.
I looked at a couple of other examples of devices that are children of
syscon nodes (e.g. armada-ap806-thermal, ap806-cpu-clock) these do have
a reg property in the dts but as far as I can see from the code it's not
actually used, instead the register offsets are in the code looked up
from the driver data (in at least one-case the reg offset is for a
legacy usage).
So I'm a little unsure what to do here. I can add a reg property and
update the driver to use that to get the offset for the first set of
registers (or just not use it). Or I could drop the @36c from the node
names but then I coudn't distinguish the two controllers without failing
the $nodename: requirement from i2c-controller.yaml.
Use 'reg'. Looks like you need 2 entries for it.
Whether a driver of some OS decides to use it or not is irrelevant to
the binding.
OK thanks for that clarification.
.../bindings/i2c/realtek,rtl9300-i2c.yaml | 73 +++++++++++++++++++
MAINTAINERS | 6 ++
2 files changed, 79 insertions(+)
create mode 100644 Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml
diff --git a/Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml b/Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml
new file mode 100644
index 000000000000..5b74a1986720
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/realtek,rtl9300-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek RTL I2C Controller
+
+maintainers:
+ - Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
+
+description: |
Don't need '|' if no formatting.
Ack
+ The RTL9300 SoC has two I2C controllers. Each of these has an SCL line (which
+ if not-used for SCL can be a GPIO). There are 8 common SDA lines that can be
+ assigned to either I2C controller.
+
+properties:
+ compatible:
+ const: realtek,rtl9300-i2c
+
+ realtek,control-offset:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Offset of the registers for this I2C controller
+
+ realtek,global-control-offset:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Offset of the I2C global control register (common between
+ controllers).
+
+ clock-frequency:
+ enum: [ 100000, 400000 ]
+
+ realtek,sda-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
0 is already the minimum.
Ack
+ maximum: 7
+ description:
+ SDA pin associated with this I2C controller.
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+
+unevaluatedProperties: false
+
+required:
+ - compatible
+ - realtek,control-offset
+ - realtek,global-control-offset
+
+examples:
+ - |
+ switch@1b000000 {
+ compatible = "realtek,rtl9302c-switch", "syscon", "simple-mfd";
+ reg = <0x1b000000 0x10000>;
+
+ i2c@36c {
+ compatible = "realtek,rtl9300-i2c";
+ realtek,control-offset = <0x36c>;
+ realtek,global-control-offset = <0x384>;
+ clock-frequency = <100000>;
+ realtek,sda-pin = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@388 {
+ compatible = "realtek,rtl9300-i2c";
+ realtek,control-offset = <0x388>;
+ realtek,global-control-offset = <0x384>;
Humm, normally we don't want the same address in multiple 'reg' entries.
Is this offset known to vary? It could just be hardcoded in the driver
or implicit from the compatible (different compatible is the usual way
to deal with differing register layouts).
It's one of those annoying registers that is sandwiched between the two
I2C controllers that affects both of them so you kind of need to use it
whether your using I2C1 or I2C2. For the RTL9300 it'll always be 0x384.
There is a RTL9310 that appears to have it at a different offset but I'm
not planning on adding support for that chip any time soon.
If I switch to "reg" for the I2C controller registers as suggested above
I can just go with a hard coded register value in the driver for the
global control.
