Re: [PATCH 1/5] dt-bindings: i2c: Add RTL9300 I2C controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 18 Sep 2024 11:29:28 +1200, Chris Packham wrote:
> Add dtschema for the I2C controller on the RTL9300 SoC. The I2C
> controllers on this SoC are part of the "switch" block which is
> represented here as a syscon node. The SCL pins are dependent on the I2C
> controller (GPIO8 for the first controller, GPIO 17 for the second). The
> SDA pins can be assigned to either one of the I2C controllers (but not
> both).
> 
> Signed-off-by: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
> ---
> 
> Notes:
>     This does hit generate the following dt_binding_check warning
> 
>     realtek,rtl9300-i2c.example.dts:22.19-30.13: Warning (unit_address_vs_reg): /example-0/switch@1b000000/i2c@36c: node has a unit name, but no reg or ranges property
> 
>     Which is totally correct. I haven't given this thing a reg property
>     because I'm using an offset from the parent syscon node. I'm also not
>     calling the first offset "offset" but I don't think that'd help.
> 
>     I looked at a couple of other examples of devices that are children of
>     syscon nodes (e.g. armada-ap806-thermal, ap806-cpu-clock) these do have
>     a reg property in the dts but as far as I can see from the code it's not
>     actually used, instead the register offsets are in the code looked up
>     from the driver data (in at least one-case the reg offset is for a
>     legacy usage).
> 
>     So I'm a little unsure what to do here. I can add a reg property and
>     update the driver to use that to get the offset for the first set of
>     registers (or just not use it). Or I could drop the @36c from the node
>     names but then I coudn't distinguish the two controllers without failing
>     the $nodename: requirement from i2c-controller.yaml.
> 
>  .../bindings/i2c/realtek,rtl9300-i2c.yaml     | 73 +++++++++++++++++++
>  MAINTAINERS                                   |  6 ++
>  2 files changed, 79 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.example.dts:22.19-30.13: Warning (unit_address_vs_reg): /example-0/switch@1b000000/i2c@36c: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.example.dts:32.19-38.13: Warning (unit_address_vs_reg): /example-0/switch@1b000000/i2c@388: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.example.dtb: /example-0/switch@1b000000: failed to match any schema with compatible: ['realtek,rtl9302c-switch', 'syscon', 'simple-mfd']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240917232932.3641992-2-chris.packham@xxxxxxxxxxxxxxxxxxx

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.





[Index of Archives]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux