[PATCH v2 10/11] pinctrl: eyeq5: add platform driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the Mobileye EyeQ5 pin controller driver. It belongs to a syscon
region called OLB.

Existing pins and their function live statically in the driver code
rather than in the devicetree, see compatible match data.

Device is only used as MFD cell.
No compatible is registered; device only appears on EyeQ5.

Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: Théo Lebrun <theo.lebrun@xxxxxxxxxxx>
---
 MAINTAINERS                     |   1 +
 drivers/pinctrl/Kconfig         |  14 +
 drivers/pinctrl/Makefile        |   1 +
 drivers/pinctrl/pinctrl-eyeq5.c | 573 ++++++++++++++++++++++++++++++++++++++++
 4 files changed, 589 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 36f4001c7f51..09c3b05035d2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14931,6 +14931,7 @@ F:	arch/mips/boot/dts/mobileye/
 F:	arch/mips/configs/eyeq5_defconfig
 F:	arch/mips/mobileye/board-epm5.its.S
 F:	drivers/clk/clk-eyeq5.c
+F:	drivers/pinctrl/pinctrl-eyeq5.c
 F:	drivers/reset/reset-eyeq5.c
 F:	include/dt-bindings/clock/mobileye,eyeq5-clk.h
 
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index d45657aa986a..b266326372e2 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -213,6 +213,20 @@ config PINCTRL_EQUILIBRIUM
 	  desired pin functions, configure GPIO attributes for LGM SoC pins.
 	  Pin muxing and pin config settings are retrieved from device tree.
 
+config PINCTRL_EYEQ5
+	bool "Mobileye EyeQ5 pinctrl driver"
+	depends on MACH_EYEQ5 || COMPILE_TEST
+	select PINMUX
+	select GENERIC_PINCONF
+	select MFD_SYSCON
+	default MACH_EYEQ5
+	help
+	  Pin controller driver for the Mobileye EyeQ5 platform. It does both
+	  pin config & pin muxing. It does not handle GPIO.
+
+	  Pin muxing supports two functions for each pin: first is GPIO, second
+	  is pin-dependent. Pin config is about bias & drive strength.
+
 config PINCTRL_GEMINI
 	bool
 	depends on ARCH_GEMINI
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 2152539b53d5..6113e980cdb2 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
 obj-$(CONFIG_PINCTRL_DA9062)	+= pinctrl-da9062.o
 obj-$(CONFIG_PINCTRL_DIGICOLOR)	+= pinctrl-digicolor.o
 obj-$(CONFIG_PINCTRL_EQUILIBRIUM)   += pinctrl-equilibrium.o
+obj-$(CONFIG_PINCTRL_EYEQ5)	+= pinctrl-eyeq5.o
 obj-$(CONFIG_PINCTRL_GEMINI)	+= pinctrl-gemini.o
 obj-$(CONFIG_PINCTRL_INGENIC)	+= pinctrl-ingenic.o
 obj-$(CONFIG_PINCTRL_K210)	+= pinctrl-k210.o
diff --git a/drivers/pinctrl/pinctrl-eyeq5.c b/drivers/pinctrl/pinctrl-eyeq5.c
new file mode 100644
index 000000000000..9e4547aa2a7d
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-eyeq5.c
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Pinctrl driver for the Mobileye EyeQ5 platform.
+ *
+ * The registers are located in a syscon region called OLB. There are two pin
+ * banks, each being controlled by 5 registers (see enum eq5p_regs) for
+ * pull-down, pull-up, drive strength and muxing.
+ *
+ * For each pin, muxing is between two functions: (0) GPIO or (1) another one
+ * that is pin-dependent. Functions are declared statically in this driver.
+ *
+ * We create pinctrl groups that are 1:1 equivalent to pins: each group has a
+ * single pin, and its index/selector is the pin number.
+ *
+ * We use eq5p_ as prefix, as-in "EyeQ5 Pinctrl", but way shorter.
+ *
+ * Copyright (C) 2024 Mobileye Vision Technologies Ltd.
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/bug.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include "core.h"
+#include "pinctrl-utils.h"
+
+struct eq5p_pinctrl {
+	struct pinctrl_desc	desc;
+	void __iomem		*base;
+};
+
+enum eq5p_bank {
+	EQ5P_BANK_A,
+	EQ5P_BANK_B,
+
+	EQ5P_BANK_COUNT,
+};
+
+enum eq5p_regs {
+	EQ5P_PD,
+	EQ5P_PU,
+	EQ5P_DS_LOW,
+	EQ5P_DS_HIGH,
+	EQ5P_IOCR,
+
+	EQ5P_REG_COUNT,
+};
+
+static const unsigned int eq5p_regs[EQ5P_BANK_COUNT][EQ5P_REG_COUNT] = {
+	[EQ5P_BANK_A] = {0x010, 0x014, 0x020, 0x024, 0x000},
+	[EQ5P_BANK_B] = {0x018, 0x01C, 0x028, 0x02C, 0x004},
+};
+
+/*
+ * Drive strength; two bits per pin.
+ */
+#define EQ5P_DS_MASK	GENMASK(1, 0)
+
+/*
+ * Comments to the right of each pin are the "signal name" in the datasheet.
+ */
+static const struct pinctrl_pin_desc eq5p_pins[] = {
+	/* Bank A */
+	PINCTRL_PIN(0,  "PA0"),  /* A0_TIMER0_CK */
+	PINCTRL_PIN(1,  "PA1"),  /* A1_TIMER0_EOC */
+	PINCTRL_PIN(2,  "PA2"),  /* A2_TIMER1_CK */
+	PINCTRL_PIN(3,  "PA3"),  /* A3_TIMER1_EOC */
+	PINCTRL_PIN(4,  "PA4"),  /* A4_TIMER2_CK */
+	PINCTRL_PIN(5,  "PA5"),  /* A5_TIMER2_EOC */
+	PINCTRL_PIN(6,  "PA6"),  /* A6_TIMER5_EXT_INCAP1 */
+	PINCTRL_PIN(7,  "PA7"),  /* A7_TIMER5_EXT_INCAP2 */
+	PINCTRL_PIN(8,  "PA8"),  /* A8_TIMER5_EXT_OUTCMP1 */
+	PINCTRL_PIN(9,  "PA9"),  /* A9_TIMER5_EXT_OUTCMP2 */
+	PINCTRL_PIN(10, "PA10"), /* A10_UART_0_TX */
+	PINCTRL_PIN(11, "PA11"), /* A11_UART_0_RX */
+	PINCTRL_PIN(12, "PA12"), /* A12_UART_1_TX */
+	PINCTRL_PIN(13, "PA13"), /* A13_UART_1_RX */
+	PINCTRL_PIN(14, "PA14"), /* A14_CAN_0_TX */
+	PINCTRL_PIN(15, "PA15"), /* A15_CAN_0_RX */
+	PINCTRL_PIN(16, "PA16"), /* A16_CAN_1_TX */
+	PINCTRL_PIN(17, "PA17"), /* A17_CAN_1_RX */
+	PINCTRL_PIN(18, "PA18"), /* A18_SPI_0_DO */
+	PINCTRL_PIN(19, "PA19"), /* A19_SPI_0_DI */
+	PINCTRL_PIN(20, "PA20"), /* A20_SPI_0_CK */
+	PINCTRL_PIN(21, "PA21"), /* A21_SPI_0_CS0 */
+	PINCTRL_PIN(22, "PA22"), /* A22_SPI_0_CS1 */
+	PINCTRL_PIN(23, "PA23"), /* A23_SPI_1_DO */
+	PINCTRL_PIN(24, "PA24"), /* A24_SPI_1_DI */
+	PINCTRL_PIN(25, "PA25"), /* A25_SPI_1_CK */
+	PINCTRL_PIN(26, "PA26"), /* A26_SPI_1_CS0 */
+	PINCTRL_PIN(27, "PA27"), /* A27_SPI_1_CS1 */
+	PINCTRL_PIN(28, "PA28"), /* A28_REF_CLK0 */
+
+#define EQ5P_PIN_OFFSET_BANK_B	29
+
+	/* Bank B */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 0,  "PB0"),  /* B0_TIMER3_CK */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 1,  "PB1"),  /* B1_TIMER3_EOC */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 2,  "PB2"),  /* B2_TIMER4_CK */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 3,  "PB3"),  /* B3_TIMER4_EOC */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 4,  "PB4"),  /* B4_TIMER6_EXT_INCAP1 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 5,  "PB5"),  /* B5_TIMER6_EXT_INCAP2 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 6,  "PB6"),  /* B6_TIMER6_EXT_OUTCMP1 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 7,  "PB7"),  /* B7_TIMER6_EXT_OUTCMP2 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 8,  "PB8"),  /* B8_UART_2_TX */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 9,  "PB9"),  /* B9_UART_2_RX */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 10, "PB10"), /* B10_CAN_2_TX */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 11, "PB11"), /* B11_CAN_2_RX */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 12, "PB12"), /* B12_SPI_2_DO */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 13, "PB13"), /* B13_SPI_2_DI */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 14, "PB14"), /* B14_SPI_2_CK */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 15, "PB15"), /* B15_SPI_2_CS0 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 16, "PB16"), /* B16_SPI_2_CS1 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 17, "PB17"), /* B17_SPI_3_DO */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 18, "PB18"), /* B18_SPI_3_DI */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 19, "PB19"), /* B19_SPI_3_CK */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 20, "PB20"), /* B20_SPI_3_CS0 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 21, "PB21"), /* B21_SPI_3_CS1 */
+	PINCTRL_PIN(EQ5P_PIN_OFFSET_BANK_B + 22, "PB22"), /* B22_MCLK0 */
+};
+
+static const char * const gpio_groups[] = {
+	/* Bank A */
+	"PA0",  "PA1",  "PA2",  "PA3",  "PA4",  "PA5",  "PA6",  "PA7",
+	"PA8",  "PA9",  "PA10", "PA11", "PA12", "PA13", "PA14", "PA15",
+	"PA16", "PA17", "PA18", "PA19", "PA20", "PA21", "PA22", "PA23",
+	"PA24", "PA25", "PA26", "PA27", "PA28",
+
+	/* Bank B */
+	"PB0",  "PB1",  "PB2",  "PB3",  "PB4",  "PB5",  "PB6",  "PB7",
+	"PB8",  "PB9",  "PB10", "PB11", "PB12", "PB13", "PB14", "PB15",
+	"PB16", "PB17", "PB18", "PB19", "PB20", "PB21", "PB22",
+};
+
+/* Groups of functions on bank A */
+static const char * const timer0_groups[] = { "PA0", "PA1" };
+static const char * const timer1_groups[] = { "PA2", "PA3" };
+static const char * const timer2_groups[] = { "PA4", "PA5" };
+static const char * const timer5_groups[] = { "PA6", "PA7", "PA8", "PA9" };
+static const char * const uart0_groups[] = { "PA10", "PA11" };
+static const char * const uart1_groups[] = { "PA12", "PA13" };
+static const char * const can0_groups[] = { "PA14", "PA15" };
+static const char * const can1_groups[] = { "PA16", "PA17" };
+static const char * const spi0_groups[] = { "PA18", "PA19", "PA20", "PA21", "PA22" };
+static const char * const spi1_groups[] = { "PA23", "PA24", "PA25", "PA26", "PA27" };
+static const char * const refclk0_groups[] = { "PA28" };
+
+/* Groups of functions on bank B */
+static const char * const timer3_groups[] = { "PB0", "PB1" };
+static const char * const timer4_groups[] = { "PB2", "PB3" };
+static const char * const timer6_groups[] = { "PB4", "PB5", "PB6", "PB7" };
+static const char * const uart2_groups[] = { "PB8", "PB9" };
+static const char * const can2_groups[] = { "PB10", "PB11" };
+static const char * const spi2_groups[] = { "PB12", "PB13", "PB14", "PB15", "PB16" };
+static const char * const spi3_groups[] = { "PB17", "PB18", "PB19", "PB20", "PB21" };
+static const char * const mclk0_groups[] = { "PB22" };
+
+static const struct pinfunction eq5p_functions[] = {
+	/* GPIO having a fixed index is depended upon, see GPIO_FUNC_SELECTOR. */
+	PINCTRL_PINFUNCTION("gpio", gpio_groups, ARRAY_SIZE(gpio_groups)),
+#define GPIO_FUNC_SELECTOR 0
+
+	/* Bank A functions */
+	PINCTRL_PINFUNCTION("timer0", timer0_groups, ARRAY_SIZE(timer0_groups)),
+	PINCTRL_PINFUNCTION("timer1", timer1_groups, ARRAY_SIZE(timer1_groups)),
+	PINCTRL_PINFUNCTION("timer2", timer2_groups, ARRAY_SIZE(timer2_groups)),
+	PINCTRL_PINFUNCTION("timer5", timer5_groups, ARRAY_SIZE(timer5_groups)),
+	PINCTRL_PINFUNCTION("uart0", uart0_groups, ARRAY_SIZE(uart0_groups)),
+	PINCTRL_PINFUNCTION("uart1", uart1_groups, ARRAY_SIZE(uart1_groups)),
+	PINCTRL_PINFUNCTION("can0", can0_groups, ARRAY_SIZE(can0_groups)),
+	PINCTRL_PINFUNCTION("can1", can1_groups, ARRAY_SIZE(can1_groups)),
+	PINCTRL_PINFUNCTION("spi0", spi0_groups, ARRAY_SIZE(spi0_groups)),
+	PINCTRL_PINFUNCTION("spi1", spi1_groups, ARRAY_SIZE(spi1_groups)),
+	PINCTRL_PINFUNCTION("refclk0", refclk0_groups, ARRAY_SIZE(refclk0_groups)),
+
+	/* Bank B functions */
+	PINCTRL_PINFUNCTION("timer3", timer3_groups, ARRAY_SIZE(timer3_groups)),
+	PINCTRL_PINFUNCTION("timer4", timer4_groups, ARRAY_SIZE(timer4_groups)),
+	PINCTRL_PINFUNCTION("timer6", timer6_groups, ARRAY_SIZE(timer6_groups)),
+	PINCTRL_PINFUNCTION("uart2", uart2_groups, ARRAY_SIZE(uart2_groups)),
+	PINCTRL_PINFUNCTION("can2", can2_groups, ARRAY_SIZE(can2_groups)),
+	PINCTRL_PINFUNCTION("spi2", spi2_groups, ARRAY_SIZE(spi2_groups)),
+	PINCTRL_PINFUNCTION("spi3", spi3_groups, ARRAY_SIZE(spi3_groups)),
+	PINCTRL_PINFUNCTION("mclk0", mclk0_groups, ARRAY_SIZE(mclk0_groups)),
+};
+
+static void eq5p_update_bits(const struct eq5p_pinctrl *pctrl,
+			     enum eq5p_bank bank, enum eq5p_regs reg,
+			     u32 mask, u32 val)
+{
+	void __iomem *ptr = pctrl->base + eq5p_regs[bank][reg];
+
+	writel((readl(ptr) & ~mask) | (val & mask), ptr);
+}
+
+static bool eq5p_test_bit(const struct eq5p_pinctrl *pctrl,
+			  enum eq5p_bank bank, enum eq5p_regs reg, int offset)
+{
+	u32 val = readl(pctrl->base + eq5p_regs[bank][reg]);
+
+	if (WARN_ON(offset > 31))
+		return false;
+
+	return (val & BIT(offset)) != 0;
+}
+
+static enum eq5p_bank eq5p_pin_to_bank(unsigned int pin)
+{
+	if (pin < EQ5P_PIN_OFFSET_BANK_B)
+		return EQ5P_BANK_A;
+	else
+		return EQ5P_BANK_B;
+}
+
+static unsigned int eq5p_pin_to_offset(unsigned int pin)
+{
+	if (pin < EQ5P_PIN_OFFSET_BANK_B)
+		return pin;
+	else
+		return pin - EQ5P_PIN_OFFSET_BANK_B;
+}
+
+static int eq5p_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(eq5p_pins);
+}
+
+static const char *eq5p_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+					       unsigned int selector)
+{
+	return pctldev->desc->pins[selector].name;
+}
+
+static int eq5p_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+				       unsigned int selector,
+				       const unsigned int **pins,
+				       unsigned int *num_pins)
+{
+	*pins = &pctldev->desc->pins[selector].number;
+	*num_pins = 1;
+	return 0;
+}
+
+static int eq5p_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
+			    unsigned long *config)
+{
+	enum pin_config_param param = pinconf_to_config_param(*config);
+	struct eq5p_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	unsigned int offset = eq5p_pin_to_offset(pin);
+	enum eq5p_bank bank = eq5p_pin_to_bank(pin);
+	u32 val_ds, arg;
+	bool pd, pu;
+
+	pd = eq5p_test_bit(pctrl, bank, EQ5P_PD, offset);
+	pu = eq5p_test_bit(pctrl, bank, EQ5P_PU, offset);
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		arg = !(pd || pu);
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		arg = pd;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		arg = pu;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		offset *= 2; /* two bits per pin */
+		if (offset >= 32) {
+			val_ds = readl(pctrl->base + eq5p_regs[bank][EQ5P_DS_HIGH]);
+			offset -= 32;
+		} else {
+			val_ds = readl(pctrl->base + eq5p_regs[bank][EQ5P_DS_LOW]);
+		}
+		arg = (val_ds >> offset) & EQ5P_DS_MASK;
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	*config = pinconf_to_config_packed(param, arg);
+	return 0;
+}
+
+static void eq5p_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
+				      struct seq_file *s,
+				      unsigned int pin)
+{
+	struct eq5p_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	const char *pin_name = pctrl->desc.pins[pin].name;
+	unsigned int offset = eq5p_pin_to_offset(pin);
+	enum eq5p_bank bank = eq5p_pin_to_bank(pin);
+	const char *func_name, *bias;
+	unsigned long ds_config;
+	u32 drive_strength;
+	bool pd, pu;
+	int i, j;
+
+	/*
+	 * First, let's get the function name. All pins have only two functions:
+	 * GPIO (IOCR == 0) and something else (IOCR == 1).
+	 */
+	if (eq5p_test_bit(pctrl, bank, EQ5P_IOCR, offset)) {
+		func_name = NULL;
+		for (i = 0; i < ARRAY_SIZE(eq5p_functions); i++) {
+			if (i == GPIO_FUNC_SELECTOR)
+				continue;
+
+			for (j = 0; j < eq5p_functions[i].ngroups; j++) {
+				/* Groups and pins are the same thing for us. */
+				const char *x = eq5p_functions[i].groups[j];
+
+				if (strcmp(x, pin_name) == 0) {
+					func_name = eq5p_functions[i].name;
+					break;
+				}
+			}
+
+			if (func_name)
+				break;
+		}
+
+		/*
+		 * We have not found the function attached to this pin, this
+		 * should never occur as all pins have exactly two functions.
+		 */
+		if (!func_name)
+			func_name = "unknown";
+	} else {
+		func_name = eq5p_functions[GPIO_FUNC_SELECTOR].name;
+	}
+
+	/* Second, we retrieve the bias. */
+	pd = eq5p_test_bit(pctrl, bank, EQ5P_PD, offset);
+	pu = eq5p_test_bit(pctrl, bank, EQ5P_PU, offset);
+	if (pd && pu)
+		bias = "both";
+	else if (pd && !pu)
+		bias = "pulldown";
+	else if (!pd && pu)
+		bias = "pullup";
+	else
+		bias = "none";
+
+	/* Third, we get the drive strength. */
+	ds_config = pinconf_to_config_packed(PIN_CONFIG_DRIVE_STRENGTH, 0);
+	eq5p_pinconf_get(pctldev, pin, &ds_config);
+	drive_strength = pinconf_to_config_argument(ds_config);
+
+	seq_printf(s, "function=%s bias=%s drive_strength=%d",
+		   func_name, bias, drive_strength);
+}
+
+static const struct pinctrl_ops eq5p_pinctrl_ops = {
+	.get_groups_count	= eq5p_pinctrl_get_groups_count,
+	.get_group_name		= eq5p_pinctrl_get_group_name,
+	.get_group_pins		= eq5p_pinctrl_get_group_pins,
+	.pin_dbg_show		= eq5p_pinctrl_pin_dbg_show,
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_pin,
+	.dt_free_map		= pinctrl_utils_free_map,
+};
+
+static int eq5p_pinmux_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(eq5p_functions);
+}
+
+static const char *eq5p_pinmux_get_function_name(struct pinctrl_dev *pctldev,
+						 unsigned int selector)
+{
+	return eq5p_functions[selector].name;
+}
+
+static int eq5p_pinmux_get_function_groups(struct pinctrl_dev *pctldev,
+					   unsigned int selector,
+					   const char * const **groups,
+					   unsigned int *num_groups)
+{
+	*groups = eq5p_functions[selector].groups;
+	*num_groups = eq5p_functions[selector].ngroups;
+	return 0;
+}
+
+static int eq5p_pinmux_set_mux(struct pinctrl_dev *pctldev,
+			       unsigned int func_selector, unsigned int pin)
+{
+	struct eq5p_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	const char *func_name = eq5p_functions[func_selector].name;
+	const char *group_name = pctldev->desc->pins[pin].name;
+	bool is_gpio = func_selector == GPIO_FUNC_SELECTOR;
+	unsigned int offset = eq5p_pin_to_offset(pin);
+	enum eq5p_bank bank = eq5p_pin_to_bank(pin);
+	u32 mask, val;
+
+	dev_dbg(pctldev->dev, "func=%s group=%s\n", func_name, group_name);
+
+	mask = BIT(offset);
+	val = is_gpio ? 0 : mask;
+	eq5p_update_bits(pctrl, bank, EQ5P_IOCR, mask, val);
+	return 0;
+}
+
+static int eq5p_pinmux_gpio_request_enable(struct pinctrl_dev *pctldev,
+					   struct pinctrl_gpio_range *range,
+					   unsigned int pin)
+{
+	/* Pin numbers and group selectors are the same thing in our case. */
+	return eq5p_pinmux_set_mux(pctldev, GPIO_FUNC_SELECTOR, pin);
+}
+
+static const struct pinmux_ops eq5p_pinmux_ops = {
+	.get_functions_count	= eq5p_pinmux_get_functions_count,
+	.get_function_name	= eq5p_pinmux_get_function_name,
+	.get_function_groups	= eq5p_pinmux_get_function_groups,
+	.set_mux		= eq5p_pinmux_set_mux,
+	.gpio_request_enable	= eq5p_pinmux_gpio_request_enable,
+	.strict			= true,
+};
+
+static int eq5p_pinconf_set_drive_strength(struct pinctrl_dev *pctldev,
+					   unsigned int pin, u32 arg)
+{
+	struct eq5p_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	unsigned int offset = eq5p_pin_to_offset(pin);
+	enum eq5p_bank bank = eq5p_pin_to_bank(pin);
+	unsigned int reg;
+	u32 mask, val;
+
+	if (arg & ~EQ5P_DS_MASK) {
+		dev_err(pctldev->dev, "Unsupported drive strength: %u\n", arg);
+		return -EINVAL;
+	}
+
+	offset *= 2; /* two bits per pin */
+
+	if (offset >= 32) {
+		reg = EQ5P_DS_HIGH;
+		offset -= 32;
+	} else {
+		reg = EQ5P_DS_LOW;
+	}
+
+	mask = EQ5P_DS_MASK << offset;
+	val = arg << offset;
+	eq5p_update_bits(pctrl, bank, reg, mask, val);
+	return 0;
+}
+
+static int eq5p_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			    unsigned long *configs, unsigned int num_configs)
+{
+	struct eq5p_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	const char *pin_name = pctldev->desc->pins[pin].name;
+	unsigned int offset = eq5p_pin_to_offset(pin);
+	enum eq5p_bank bank = eq5p_pin_to_bank(pin);
+	struct device *dev = pctldev->dev;
+	u32 val = BIT(offset);
+	unsigned int i;
+
+	for (i = 0; i < num_configs; i++) {
+		enum pin_config_param param = pinconf_to_config_param(configs[i]);
+		u32 arg = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			dev_dbg(dev, "pin=%s bias_disable\n", pin_name);
+
+			eq5p_update_bits(pctrl, bank, EQ5P_PD, val, 0);
+			eq5p_update_bits(pctrl, bank, EQ5P_PU, val, 0);
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			dev_dbg(dev, "pin=%s bias_pull_down arg=%u\n",
+				pin_name, arg);
+
+			if (arg == 0) /* cannot connect to GND */
+				return -ENOTSUPP;
+
+			eq5p_update_bits(pctrl, bank, EQ5P_PD, val, val);
+			eq5p_update_bits(pctrl, bank, EQ5P_PU, val, 0);
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_UP:
+			dev_dbg(dev, "pin=%s bias_pull_up arg=%u\n",
+				pin_name, arg);
+
+			if (arg == 0) /* cannot connect to VDD */
+				return -ENOTSUPP;
+
+			eq5p_update_bits(pctrl, bank, EQ5P_PD, val, 0);
+			eq5p_update_bits(pctrl, bank, EQ5P_PU, val, val);
+			break;
+
+		case PIN_CONFIG_DRIVE_STRENGTH:
+			dev_dbg(dev, "pin=%s drive_strength arg=%u\n",
+				pin_name, arg);
+
+			eq5p_pinconf_set_drive_strength(pctldev, pin, arg);
+			break;
+
+		default:
+			dev_err(dev, "Unsupported pinconf %u\n", param);
+			return -ENOTSUPP;
+		}
+	}
+
+	return 0;
+}
+
+static const struct pinconf_ops eq5p_pinconf_ops = {
+	.is_generic = true,
+	.pin_config_get = eq5p_pinconf_get,
+	.pin_config_set = eq5p_pinconf_set,
+	/* Pins and groups are equivalent in this driver. */
+	.pin_config_group_get = eq5p_pinconf_get,
+	.pin_config_group_set = eq5p_pinconf_set,
+};
+
+static int eq5p_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct pinctrl_dev *pctldev;
+	struct eq5p_pinctrl *pctrl;
+	int ret;
+
+	pctrl = devm_kzalloc(dev, sizeof(*pctrl), GFP_KERNEL);
+	if (!pctrl)
+		return -ENOMEM;
+
+	pctrl->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(pctrl->base))
+		return PTR_ERR(pctrl->base);
+
+	pctrl->desc.name = dev_name(dev);
+	pctrl->desc.pins = eq5p_pins;
+	pctrl->desc.npins = ARRAY_SIZE(eq5p_pins);
+	pctrl->desc.pctlops = &eq5p_pinctrl_ops;
+	pctrl->desc.pmxops = &eq5p_pinmux_ops;
+	pctrl->desc.confops = &eq5p_pinconf_ops;
+	pctrl->desc.owner = THIS_MODULE;
+
+	ret = devm_pinctrl_register_and_init(dev, &pctrl->desc, pctrl, &pctldev);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed registering pinctrl device\n");
+
+	ret = pinctrl_enable(pctldev);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed enabling pinctrl device\n");
+
+	return 0;
+}
+
+static struct platform_driver eq5p_driver = {
+	.probe = eq5p_probe,
+	.driver = {
+		.name = "eyeq5-pinctrl",
+	},
+};
+builtin_platform_driver(eq5p_driver);

-- 
2.45.0





[Index of Archives]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux