Hello,
On Mon Apr 8, 2024 at 4:10 PM CEST, Mark Brown wrote:
> On Fri, Apr 05, 2024 at 05:02:15PM +0200, Théo Lebrun wrote:
>
> > Use hardware ability to read the FIFO depth thanks to
> > CQSPI_REG_SRAMPARTITION that is partially read-only. Keep current
> > behavior identical for existing compatibles.
>
> The behaviour is not identical here - we now unconditionally probe the
> FIFO depth on all hardware, the difference with the quirk is that we
> will ignore any DT property specifying the depth.
You are correct of course. Wording is incorrect. I wanted to highlight
that FIFO depth does not change for existing HW and still relies as
before on devicetree value.
> > - if (of_property_read_u32(np, "cdns,fifo-depth", &cqspi->fifo_depth)) {
> > + if (!(ddata && ddata->quirks & CQSPI_DETECT_FIFO_DEPTH) &&
> > + of_property_read_u32(np, "cdns,fifo-depth", &cqspi->fifo_depth)) {
> > dev_err(dev, "couldn't determine fifo-depth\n");
>
> It's not obvious from just the code that we do handle having a FIFO
> depth property and detection in the detection code, at least a comment
> would be good.
I see. Will add comment or rework code to make more straight forward, or
both.
> > +static void cqspi_controller_detect_fifo_depth(struct cqspi_st *cqspi)
> > +{
> > + const struct cqspi_driver_platdata *ddata = cqspi->ddata;
> > + struct device *dev = &cqspi->pdev->dev;
> > + u32 reg, fifo_depth;
> > +
> > + /*
> > + * Bits N-1:0 are writable while bits 31:N are read as zero, with 2^N
> > + * the FIFO depth.
> > + */
> > + writel(U32_MAX, cqspi->iobase + CQSPI_REG_SRAMPARTITION);
> > + reg = readl(cqspi->iobase + CQSPI_REG_SRAMPARTITION);
> > + fifo_depth = reg + 1;
> > +
> > + if (ddata && ddata->quirks & CQSPI_DETECT_FIFO_DEPTH) {
> > + cqspi->fifo_depth = fifo_depth;
> > + dev_dbg(dev, "using FIFO depth of %u\n", fifo_depth);
> > + } else if (fifo_depth != cqspi->fifo_depth) {
> > + dev_warn(dev, "detected FIFO depth (%u) different from config (%u)\n",
> > + fifo_depth, cqspi->fifo_depth);
> > + }
>
> It's not obvious to me that we should ignore an explicitly specified
> property if the quirk is present
DT value isn't expected for compatibles with CQSPI_DETECT_FIFO_DEPTH
quirk, therefore we do not ignore a specified property. Bindings agree:
prop is false with EyeQ5 compatible.
> - if anything I'd more expect to see
> the new warning in that case, possibly with a higher severity if we're
> saying that the quirk means we're more confident that the data reported
> by the hardware is reliable. I think what I'd expect is that we always
> use an explicitly specified depth (hopefully the user was specifying it
> for a reason?).
The goal was a simpler devicetree on Mobileye platform. This is why we
add this behavior flag. You prefer the property to be always present?
This is a only a nice-to-have, you tell me what you prefer.
I wasn't sure all HW behaved in the same way wrt read-only bits in
SRAMPARTITION, and I do not have access to other platforms exploiting
this driver. This is why I kept behavior reserved for EyeQ5-integrated
IP block.
> Pulling all the above together can we just drop the quirk and always do
> the detection, or leave the quirk as just controlling the severity with
> which we log any difference between detected and explicitly configured
> depths?
If we do not simplify devicetree, then I'd vote for dropping this patch
entirely. Adding code for detecting such an edge-case doesn't sound
useful. Especially since this kind of error should only occur to people
adding new hardware support; those probably do not need a nice
user-facing error message. What do you think?
Regards,
--
Théo Lebrun, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
