On Tue, Sep 12, 2023 at 6:12 PM Serge Semin <fancer.lancer@xxxxxxxxx> wrote:
>
> On Wed, Aug 30, 2023 at 09:42:40PM +0800, Keguang Zhang wrote:
> > This glue driver is created based on the arch-code
> > implemented earlier with the platform-specific settings.
> >
> > Use syscon for SYSCON register access.
> >
> > Partially based on the previous work by Serge Semin.
> >
> > Signed-off-by: Keguang Zhang <keguang.zhang@xxxxxxxxx>
> > ---
> > V3 -> V4: Drop ls1x_dwmac_syscon definition and its instances
> > Drop three redundant fields from the ls1x_dwmac structure
> > Drop the ls1x_dwmac_init() method.
> > Some minor improvements
> > V2 -> V3: Determine the device ID by physical
> > base address(suggested by Serge Semin)
> > Use regmap instead of regmap fields
> > Use syscon_regmap_lookup_by_phandle()
> > Some minor fixes
> > V1 -> V2: Fix the build errors due to CONFIG_OF being unset
> > Change struct reg_field definitions to const
> > Rename the syscon property to "loongson,dwmac-syscon"
> > Add MII PHY mode for LS1C
> >
> > drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
> > drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> > .../ethernet/stmicro/stmmac/dwmac-loongson1.c | 219 ++++++++++++++++++
> > 3 files changed, 231 insertions(+)
> > create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > index 06c6871f8788..a2b9e289aa36 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > @@ -239,6 +239,17 @@ config DWMAC_INTEL_PLAT
> > the stmmac device driver. This driver is used for the Intel Keem Bay
> > SoC.
> >
> > +config DWMAC_LOONGSON1
> > + tristate "Loongson1 GMAC support"
> > + default MACH_LOONGSON32
> > + depends on OF && (MACH_LOONGSON32 || COMPILE_TEST)
> > + help
> > + Support for ethernet controller on Loongson1 SoC.
> > +
> > + This selects Loongson1 SoC glue layer support for the stmmac
> > + device driver. This driver is used for Loongson1-based boards
> > + like Loongson LS1B/LS1C.
> > +
> > config DWMAC_TEGRA
> > tristate "NVIDIA Tegra MGBE support"
> > depends on ARCH_TEGRA || COMPILE_TEST
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > index 5b57aee19267..80e598bd4255 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > @@ -29,6 +29,7 @@ obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
> > obj-$(CONFIG_DWMAC_SUN8I) += dwmac-sun8i.o
> > obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
> > obj-$(CONFIG_DWMAC_INTEL_PLAT) += dwmac-intel-plat.o
> > +obj-$(CONFIG_DWMAC_LOONGSON1) += dwmac-loongson1.o
> > obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
> > obj-$(CONFIG_DWMAC_IMX8) += dwmac-imx.o
> > obj-$(CONFIG_DWMAC_TEGRA) += dwmac-tegra.o
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> > new file mode 100644
> > index 000000000000..f1732f15ff87
> > --- /dev/null
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> > @@ -0,0 +1,219 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Loongson-1 DWMAC glue layer
> > + *
> > + * Copyright (C) 2011-2023 Keguang Zhang <keguang.zhang@xxxxxxxxx>
> > + */
> > +
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +
> > +#include "stmmac.h"
> > +#include "stmmac_platform.h"
> > +
>
> > +#define LS1B_GMAC0_BASE (0x1fe10000)
>
> I was talking about the LS1B_GMAC1_BASE macro only. Since both LS1B
> and LS1C have GMAC0 at the same base address I would preserve
> LS1X_GMAC0_BASE name here. But seeing it's unused for the LS1C anyway
> it's not that a big deal.
>
> > +#define LS1B_GMAC1_BASE (0x1fe20000)
> > +
> > +/* Loongson-1 SYSCON Registers */
> > +#define LS1X_SYSCON0 (0x0)
> > +#define LS1X_SYSCON1 (0x4)
> > +
> > +/* Loongson-1B SYSCON Register Bits */
> > +#define GMAC1_USE_UART1 BIT(4)
> > +#define GMAC1_USE_UART0 BIT(3)
> > +
> > +#define GMAC1_SHUT BIT(13)
> > +#define GMAC0_SHUT BIT(12)
> > +
> > +#define GMAC1_USE_TXCLK BIT(3)
> > +#define GMAC0_USE_TXCLK BIT(2)
> > +#define GMAC1_USE_PWM23 BIT(1)
> > +#define GMAC0_USE_PWM01 BIT(0)
> > +
> > +/* Loongson-1C SYSCON Register Bits */
> > +#define GMAC_SHUT BIT(6)
> > +
> > +#define PHY_INTF_SELI GENMASK(30, 28)
> > +#define PHY_INTF_MII FIELD_PREP(PHY_INTF_SELI, 0)
> > +#define PHY_INTF_RMII FIELD_PREP(PHY_INTF_SELI, 4)
> > +
> > +struct ls1x_dwmac {
> > + struct plat_stmmacenet_data *plat_dat;
> > + struct regmap *regmap;
> > +};
> > +
> > +static int ls1b_dwmac_syscon_init(struct platform_device *pdev, void *priv)
> > +{
> > + struct ls1x_dwmac *dwmac = priv;
> > + struct plat_stmmacenet_data *plat = dwmac->plat_dat;
> > + struct regmap *regmap = dwmac->regmap;
> > + struct resource *res;
> > + unsigned long reg_base;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res) {
> > + dev_err(&pdev->dev, "Could not get IO_MEM resources\n");
> > + return -EINVAL;
> > + }
> > + reg_base = (unsigned long)res->start;
> > +
> > + if (reg_base == LS1B_GMAC0_BASE) {
> > + switch (plat->phy_interface) {
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + regmap_update_bits(regmap, LS1X_SYSCON0,
> > + GMAC0_USE_TXCLK | GMAC0_USE_PWM01,
> > + 0);
> > + break;
> > + case PHY_INTERFACE_MODE_MII:
> > + regmap_update_bits(regmap, LS1X_SYSCON0,
> > + GMAC0_USE_TXCLK | GMAC0_USE_PWM01,
> > + GMAC0_USE_TXCLK | GMAC0_USE_PWM01);
> > + break;
> > + default:
> > + dev_err(&pdev->dev, "Unsupported PHY mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_update_bits(regmap, LS1X_SYSCON0, GMAC0_SHUT, 0);
> > + } else if (reg_base == LS1B_GMAC1_BASE) {
> > + regmap_update_bits(regmap, LS1X_SYSCON0,
> > + GMAC1_USE_UART1 | GMAC1_USE_UART0,
> > + GMAC1_USE_UART1 | GMAC1_USE_UART0);
> > +
> > + switch (plat->phy_interface) {
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + regmap_update_bits(regmap, LS1X_SYSCON1,
> > + GMAC1_USE_TXCLK | GMAC1_USE_PWM23,
> > + 0);
> > +
> > + break;
> > + case PHY_INTERFACE_MODE_MII:
> > + regmap_update_bits(regmap, LS1X_SYSCON1,
> > + GMAC1_USE_TXCLK | GMAC1_USE_PWM23,
> > + GMAC1_USE_TXCLK | GMAC1_USE_PWM23);
> > + break;
> > + default:
> > + dev_err(&pdev->dev, "Unsupported PHY mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_update_bits(regmap, LS1X_SYSCON1, GMAC1_SHUT, 0);
> > + } else {
> > + dev_err(&pdev->dev, "Invalid Ethernet MAC base address %lx",
> > + reg_base);
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ls1c_dwmac_syscon_init(struct platform_device *pdev, void *priv)
> > +{
> > + struct ls1x_dwmac *dwmac = priv;
> > + struct plat_stmmacenet_data *plat = dwmac->plat_dat;
> > + struct regmap *regmap = dwmac->regmap;
> > +
> > + switch (plat->phy_interface) {
> > + case PHY_INTERFACE_MODE_MII:
> > + regmap_update_bits(regmap, LS1X_SYSCON1, PHY_INTF_SELI,
> > + PHY_INTF_MII);
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + regmap_update_bits(regmap, LS1X_SYSCON1, PHY_INTF_SELI,
> > + PHY_INTF_RMII);
> > + break;
> > + default:
> > + dev_err(&pdev->dev, "Unsupported PHY-mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_update_bits(regmap, LS1X_SYSCON0, GMAC0_SHUT, 0);
> > +
> > + return 0;
> > +}
> > +
> > +static int ls1x_dwmac_probe(struct platform_device *pdev)
> > +{
> > + struct plat_stmmacenet_data *plat_dat;
> > + struct stmmac_resources stmmac_res;
> > + struct regmap *regmap;
> > + struct ls1x_dwmac *dwmac;
> > + int (*init)(struct platform_device *pdev, void *priv);
> > + int ret;
> > +
> > + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> > + if (ret)
> > + return ret;
> > +
> > + /* Probe syscon */
> > + regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> > + "loongson,ls1-syscon");
> > + if (IS_ERR(regmap))
> > + return dev_err_probe(&pdev->dev, PTR_ERR(regmap),
> > + "Unable to find syscon\n");
> > +
> > + init = of_device_get_match_data(&pdev->dev);
> > + if (!init) {
> > + dev_err(&pdev->dev, "No of match data provided\n");
> > + return -EINVAL;
> > + }
> > +
> > + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
> > + if (!dwmac)
> > + return -ENOMEM;
> > +
>
> > + plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
>
> This can be replaced with devm_stmmac_probe_config_dt() and ...
>
> > + if (IS_ERR(plat_dat))
> > + return dev_err_probe(&pdev->dev, PTR_ERR(plat_dat),
> > + "dt configuration failed\n");
> > +
> > + plat_dat->bsp_priv = dwmac;
> > + plat_dat->init = init;
> > + dwmac->plat_dat = plat_dat;
> > + dwmac->regmap = regmap;
> > +
>
> > + ret = stmmac_pltfr_probe(pdev, plat_dat, &stmmac_res);
>
> ... this can be replaced with devm_stmmac_pltfr_probe() thus ...
>
> > + if (ret)
> > + goto err_remove_config_dt;
> > +
> > + return 0;
> > +
>
> > +err_remove_config_dt:
> > + stmmac_remove_config_dt(pdev, plat_dat);
> > +
> > + return ret;
>
> ... this could have been omitted and ...
>
> > +}
> > +
> > +static const struct of_device_id ls1x_dwmac_match[] = {
> > + {
> > + .compatible = "loongson,ls1b-gmac",
> > + .data = &ls1b_dwmac_syscon_init,
> > + },
> > + {
> > + .compatible = "loongson,ls1c-emac",
> > + .data = &ls1c_dwmac_syscon_init,
> > + },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, ls1x_dwmac_match);
> > +
> > +static struct platform_driver ls1x_dwmac_driver = {
> > + .probe = ls1x_dwmac_probe,
>
> > + .remove_new = stmmac_pltfr_remove,
>
> ... this could have been dropped.
>
Will do all the above changes.
Thanks!
> -Serge(y)
>
> > + .driver = {
> > + .name = "loongson1-dwmac",
> > + .of_match_table = ls1x_dwmac_match,
> > + },
> > +};
> > +module_platform_driver(ls1x_dwmac_driver);
> > +
> > +MODULE_AUTHOR("Keguang Zhang <keguang.zhang@xxxxxxxxx>");
> > +MODULE_DESCRIPTION("Loongson-1 DWMAC glue layer");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.39.2
> >
> >
--
Best regards,
Keguang Zhang
