Re: [PATCH v3 1/2] mips: dts: ralink: Add support for TP-Link HC220 G5 v1 board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jun 06, 2023 at 08:24:48AM +0300, Arınç ÜNAL wrote:
> On 6.06.2023 00:01, Liviu Dudau wrote:
> > On Mon, Jun 05, 2023 at 07:35:44PM +0300, Arınç ÜNAL wrote:
> > > On 5.06.2023 18:01, Liviu Dudau wrote:
> > > > This WiFi AP is based on a MT7621 SoC with 128MiB RAM, 128MiB NAND,
> > > > a MT7603 2.4GHz WiFi and a MT7613 5GHz WiFi chips integrated on the board,
> > > > connected to the main SoC over PCIe.
> > > > 
> > > > The device uses NMBM over NAND, which is not currently supported in the
> > > > mainline, so NAND node is skipped in this revision.
> > > > 
> > > > Signed-off-by: Liviu Dudau <liviu@xxxxxxxxxxx>
> > > > ---
> > > >    arch/mips/boot/dts/ralink/Makefile            |  3 +-
> > > >    .../dts/ralink/mt7621-tplink-hc220-g5-v1.dts  | 92 +++++++++++++++++++
> > > >    2 files changed, 94 insertions(+), 1 deletion(-)
> > > >    create mode 100644 arch/mips/boot/dts/ralink/mt7621-tplink-hc220-g5-v1.dts
> > > > 
> > > > diff --git a/arch/mips/boot/dts/ralink/Makefile b/arch/mips/boot/dts/ralink/Makefile
> > > > index 11732b8c8163a..d27d7e8c700fe 100644
> > > > --- a/arch/mips/boot/dts/ralink/Makefile
> > > > +++ b/arch/mips/boot/dts/ralink/Makefile
> > > > @@ -8,6 +8,7 @@ dtb-$(CONFIG_DTB_VOCORE2)	+= vocore2.dtb
> > > >    dtb-$(CONFIG_SOC_MT7621) += \
> > > >    	mt7621-gnubee-gb-pc1.dtb \
> > > > -	mt7621-gnubee-gb-pc2.dtb
> > > > +	mt7621-gnubee-gb-pc2.dtb \
> > > > +	mt7621-tplink-hc220-g5-v1.dtb
> > > >    obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
> > > > diff --git a/arch/mips/boot/dts/ralink/mt7621-tplink-hc220-g5-v1.dts b/arch/mips/boot/dts/ralink/mt7621-tplink-hc220-g5-v1.dts
> > > > new file mode 100644
> > > > index 0000000000000..859aaa1c1bc2b
> > > > --- /dev/null
> > > > +++ b/arch/mips/boot/dts/ralink/mt7621-tplink-hc220-g5-v1.dts
> > > > @@ -0,0 +1,92 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > +/dts-v1/;
> > > > +
> > > > +#include "mt7621.dtsi"
> > > > +
> > > > +#include <dt-bindings/gpio/gpio.h>
> > > > +#include <dt-bindings/input/input.h>
> > > > +#include <dt-bindings/leds/common.h>
> > > > +
> > > > +/ {
> > > > +	compatible = "tplink,hc220-g5-v1", "mediatek,mt7621-soc";
> > > > +	model = "TP-Link HC220 G5 v1";
> > > > +
> > > > +	memory@0 {
> > > > +		device_type = "memory";
> > > > +		reg = <0x00000000 0x8000000>;
> > > 
> > > Please use 8 digit addressing for the memory start and size offsets:
> > > 
> > > 0x00000000 0x08000000
> > 
> > Will do.
> > 
> > > 
> > > > +	};
> > > > +
> > > > +	chosen {
> > > > +		bootargs = "earlycon console=ttyS0,115200";
> > > > +	};
> > > > +
> > > > +	gpio-keys {
> > > > +		compatible = "gpio-keys";
> > > > +
> > > > +		key-reset {
> > > > +			label = "reset";
> > > > +			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> > > > +			linux,code = <KEY_RESTART>;
> > > > +		};
> > > > +
> > > > +		key-wps {
> > > > +			label = "wps";
> > > > +			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> > > > +			linux,code = <KEY_WPS_BUTTON>;
> > > > +		};
> > > > +	};
> > > > +
> > > > +	leds {
> > > > +		compatible = "gpio-leds";
> > > > +
> > > > +		red {
> > > 
> > > Usually the led name would point to the component the LED is used for.
> > 
> > These are "generic" LEDs controlled from the userspace. The original firmware
> > uses GREEN for normal operations, RED for faults and BLUE for when WPS is
> > enabled. I'm not sure if there are any standard bindings that I can use here.
> 
> Looking at:
> 
> https://www.kernel.org/doc/html/latest/leds/leds-class.html#led-device-naming
> 
> You could use red:fault, green:power, and blue:wps. For node names,
> led-fault, led-power, and led-wps.

Without making any changes in the device tree, because of the use of 'function' property,
I get this:

# ls -al /sys/class/leds/
drwxr-xr-x    2 root     root             0 Jun  6 14:24 .
drwxr-xr-x   37 root     root             0 Jan  1  1970 ..
lrwxrwxrwx    1 root     root             0 Jun  6 14:24 blue:wps -> ../../devices/platform/leds/leds/blue:wps
lrwxrwxrwx    1 root     root             0 Jun  6 14:24 green:power -> ../../devices/platform/leds/leds/green:power
lrwxrwxrwx    1 root     root             0 Jun  6 14:24 red:fault -> ../../devices/platform/leds/leds/red:fault

May I suggest that I change only the node names and not add a label, keeping the 'function' property instead?

Best regards,
Liviu

> 
> Arınç

-- 
Everyone who uses computers frequently has had, from time to time,
a mad desire to attack the precocious abacus with an axe.
       	   	      	     	  -- John D. Clark, Ignition!



[Index of Archives]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux