Re: [PATCH V4 1/5] dt-bindings: rtc: Remove the LS2X from the trivial RTCs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 30/05/2023 10:17:43+0200, Krzysztof Kozlowski wrote:
> On 29/05/2023 10:31, Binbin Zhou wrote:
> > Hi Krzysztof:
> > 
> > Excuse me.
> > We have different opinions on how to better describe rtc-loongson compatible.
> > 
> > Based on my previous communication with you, I think we should list
> > all the Socs in the driver and drop the wildcards.
> 
> Suggestion was about the bindings. Not in the driver. I never said to
> list all compatibles in the driver...
> 
> > This should be clearer and more straightforward:
> > 
> >         { .compatible = "loongson,ls1b-rtc", .data = &ls1x_rtc_config
> > }, //ls1b soc
> >         { .compatible = "loongson,ls1c-rtc", .data = &ls1x_rtc_config
> > }, //ls1c soc
> >         { .compatible = "loongson,ls7a-rtc", .data =
> > &generic_rtc_config }, //ls7a bridge chip
> >         { .compatible = "loongson,ls2k0500-rtc", .data =
> > &generic_rtc_config }, // ls2k0500 soc
> >         { .compatible = "loongson,ls2k2000-rtc", .data =
> > &generic_rtc_config }, // ls2k2000 soc
> >         { .compatible = "loongson,ls2k1000-rtc", .data =
> > &ls2k1000_rtc_config }, // ls2k1000 soc
> 
> I would suggest to use fallbacks as suggested by Conor at least for some
> of them. You referred to my previous comments about wildcards.
> Wildcard != fallback.
> 
> > 
> > And Conor thought it should be rendered using a fallback compatible
> > form based on ".data".
> 
> Based on common (compatible) programming model unless you already have
> clear hardware differences making them incompatible.
> 
> > 
> >         "loongson,ls1b-rtc"
> >         "loongson,ls1c-rtc", "loongson,ls1b-rtc"
> >         "loongson,ls7a-rtc"
> >         "loongson,ls2k0500-rtc", "loongson,ls7a-rtc"
> >         "longson,ls2k2000-rtc", "longson,ls7a-rtc"
> >         "loonson,ls2k1000-rtc"
> > 
> >         { .compatible = "loongson,ls1b-rtc", .data = &ls1x_rtc_config }
> >         { .compatible = "loongson,ls7a-rtc", .data = &generic_rtc_config }
> >         { .compatible = "loongson,ls2k1000-rtc", .data = &ls2k1000_rtc_config }
> > 
> > In this form,  I think it might not be possible to show very
> > graphically which chips are using the driver.
> 
> ??? How is it impossible? For all other SoCs and architectures it is
> possible, so what is special for Loongson?
> 
> > Also, for example, "ls7a" is a bridge chip, while
> > "ls2k2000"/"ls2k0500" are soc chips, and it seems inappropriate to
> > integrate them into one item.
> 
> Why it is inappropriate? I don't see the issue here... what is a
> "bridge" chip? Isn't this also an SoC?
> 
> 
> > 
> > Which one do you think is more suitable for us?
> 
> Use fallbacks for some. You pointed difference in alarm for ls1x, right?
> If so, then they can stay separate.

>From what I seen the IP and register set is the same, it is just the
integration on the SoC that differs.


-- 
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com



[Index of Archives]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux