[PATCH v11 5/7] dt-bindings: display: Add Loongson display controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: suijingfeng <suijingfeng@xxxxxxxxxxx>

Signed-off-by: suijingfeng <suijingfeng@xxxxxxxxxxx>
Signed-off-by: Sui Jingfeng <15330273260@xxxxxx>
---
 .../loongson/loongson,display-controller.yaml | 230 ++++++++++++++++++
 1 file changed, 230 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml

diff --git a/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml b/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml
new file mode 100644
index 000000000000..7be63346289e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml
@@ -0,0 +1,230 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/loongson/loongson,display-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Loongson LS7A1000/LS2K1000/LS2K0500 Display Controller Device Tree Bindings
+
+maintainers:
+  - Sui Jingfeng <suijingfeng@xxxxxxxxxxx>
+
+description: |+
+
+  Loongson display controllers are simple which require scanout buffers
+  to be physically contiguous. LS2K1000/LS2K0500 is a SOC, only system
+  memory is available. LS7A1000/LS7A2000 is bridge chip which is equipped
+  with a dedicated video RAM which is 64MB or more, precise size can be
+  read from the PCI BAR 2 of the GPU device(0x0014:0x7A15) in the bridge
+  chip.
+
+  LSDC has two display pipes, each way has a DVO interface which provide
+  RGB888 signals, vertical & horizontal synchronisations, data enable and
+  the pixel clock. LSDC has two CRTC, each CRTC is able to scanout from
+  1920x1080 resolution at 60Hz. Each CRTC has two FB address registers.
+
+  For LS7A1000, there are 4 dedicated GPIOs whose control register is
+  located at the DC register space. They are used to emulate two way i2c,
+  One for DVO0, another for DVO1.
+
+  LS2K1000 and LS2K0500 SoC grab i2c adapter from other module, either
+  general purpose GPIO emulated i2c or hardware i2c in the SoC.
+
+  LSDC's display pipeline have several components as below description,
+
+  The display controller in LS7A1000:
+     ___________________                                     _________
+    |            -------|                                   |         |
+    |  CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Monitor |
+    |  _   _     -------|        ^             ^            |_________|
+    | | | | |    -------|        |             |
+    | |_| |_|    | i2c0 <--------+-------------+
+    |            -------|
+    |   DC IN LS7A1000  |
+    |  _   _     -------|
+    | | | | |    | i2c1 <--------+-------------+
+    | |_| |_|    -------|        |             |             _________
+    |            -------|        |             |            |         |
+    |  CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> |  Panel  |
+    |            -------|                                   |_________|
+    |___________________|
+
+  Simple usage of LS7A1000 with LS3A4000 CPU:
+
+    +------+            +-----------------------------------+
+    | DDR4 |            |  +-------------------+            |
+    +------+            |  | PCIe Root complex |   LS7A1000 |
+       || MC0           |  +--++---------++----+            |
+  +----------+  HT 3.0  |     ||         ||                 |
+  | LS3A4000 |<-------->| +---++---+  +--++--+    +---------+   +------+
+  |   CPU    |<-------->| | GC1000 |  | LSDC |<-->| DDR3 MC |<->| VRAM |
+  +----------+          | +--------+  +-+--+-+    +---------+   +------+
+       || MC1           +---------------|--|----------------+
+    +------+                            |  |
+    | DDR4 |          +-------+   DVO0  |  |  DVO1   +------+
+    +------+   VGA <--|ADV7125|<--------+  +-------->|TFP410|--> DVI/HDMI
+                      +-------+                      +------+
+
+  The display controller in LS2K1000/LS2K0500:
+     ___________________                                     _________
+    |            -------|                                   |         |
+    |  CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Monitor |
+    |  _   _     -------|        ^              ^           |_________|
+    | | | | |           |        |              |
+    | |_| |_|           |     +------+          |
+    |                   <---->| i2c0 |<---------+
+    |   DC IN LS2K1000  |     +------+
+    |  _   _            |     +------+
+    | | | | |           <---->| i2c1 |----------+
+    | |_| |_|           |     +------+          |            _________
+    |            -------|        |              |           |         |
+    |  CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> |  Panel  |
+    |            -------|                                   |_________|
+    |___________________|
+
+properties:
+  $nodename:
+    pattern: "^display-controller@[0-9a-f],[0-9a-f]$"
+
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - loongson,ls7a1000-dc
+              - loongson,ls2k1000-dc
+              - loongson,ls2k0500-dc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  i2c-gpio@0:
+    description: |
+      Built-in GPIO emulate i2c exported for external display bridge
+      configuration, onitor detection and edid read back etc, for ls7a1000
+      only. Its compatible must be lsdc,i2c-gpio-0. The reg property can be
+      used to specify a I2c adapter bus number, if you don't specify one
+      i2c driver core will dynamically assign a bus number. Please specify
+      it only when its bus number matters. Bus number greater than 6 is safe
+      because ls7a1000 bridge have 6 hardware I2C controller integrated.
+
+  i2c-gpio@1:
+    description: |
+      Built-in GPIO emulate i2c exported for external display bridge
+      configuration, onitor detection and edid read back etc, for ls7a1000
+      only. Its compatible must be lsdc,i2c-gpio-1.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: output port node connected with DPI panels or external encoders, with only one endpoint.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: output port node connected with DPI panels or external encoders, with only one endpoint.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    bus {
+
+        #address-cells = <3>;
+        #size-cells = <2>;
+        #interrupt-cells = <2>;
+
+        display-controller@6,1 {
+            compatible = "loongson,ls7a1000-dc";
+            reg = <0x3100 0x0 0x0 0x0 0x0>;
+            interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            i2c-gpio@0 {
+                compatible = "lsdc,i2c-gpio-0";
+                reg = <6>;
+                sda = <0>;
+                scl = <1>;
+            };
+
+            i2c-gpio@1 {
+                compatible = "lsdc,i2c-gpio-1";
+                reg = <7>;
+                sda = <2>;
+                scl = <3>;
+            };
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                port@0 {
+                    reg = <0>;
+                    endpoint {
+                            remote-endpoint = <&vga_encoder_in>;
+                    };
+                };
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                            remote-endpoint = <&dvi_encoder_in>;
+                    };
+                };
+            };
+        };
+    };
+
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    bus {
+
+        #address-cells = <3>;
+        #size-cells = <2>;
+        #interrupt-cells = <2>;
+
+        display-controller@6,0 {
+            compatible = "loongson,ls2k1000-dc";
+            reg = <0x3100 0x0 0x0 0x0 0x0>;
+            interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                port@0 {
+                    reg = <0>;
+                    endpoint {
+                            remote-endpoint = <&panel_in>;
+                    };
+                };
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                            remote-endpoint = <&hdmi_encoder_in>;
+                    };
+                };
+            };
+        };
+    };
+...
-- 
2.25.1




[Index of Archives]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux