Hi Nikolaus, Thomas,
Le mer., nov. 10 2021 at 20:43:31 +0100, H. Nikolaus Schaller
<hns@xxxxxxxxxxxxx> a écrit :
From: Paul Boddie <paul@xxxxxxxxxxxxx>
We need to hook up
* HDMI connector
* HDMI power regulator
* JZ4780_CLK_HDMI @ 27 MHz
* DDC pinmux
* HDMI and LCDC endpoint connections
Signed-off-by: Paul Boddie <paul@xxxxxxxxxxxxx>
Signed-off-by: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>
---
arch/mips/boot/dts/ingenic/ci20.dts | 73
+++++++++++++++++++++++++++--
1 file changed, 70 insertions(+), 3 deletions(-)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts
b/arch/mips/boot/dts/ingenic/ci20.dts
index a688809beebca..a62557bede565 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -78,6 +78,18 @@ eth0_power: fixedregulator@0 {
enable-active-high;
};
+ hdmi_out: connector {
+ compatible = "hdmi-connector";
+ label = "HDMI OUT";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&dw_hdmi_out>;
+ };
+ };
+ };
+
ir: ir {
compatible = "gpio-ir-receiver";
gpios = <&gpe 3 GPIO_ACTIVE_LOW>;
@@ -102,6 +114,17 @@ otg_power: fixedregulator@2 {
gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
enable-active-high;
};
+
+ hdmi_power: fixedregulator@3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "hdmi_power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpa 25 GPIO_ACTIVE_LOW>;
Just use 0 instead of GPIO_ACTIVE_LOW, since the flag is simply ignored
(I know the other regulators do use it, but I'll clean that up soon).
+ enable-active-high;
+ };
};
&ext {
@@ -113,9 +136,9 @@ &cgu {
* Use the 32.768 kHz oscillator as the parent of the RTC for a
higher
* precision.
*/
- assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>;
- assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>;
- assigned-clock-rates = <48000000>;
+ assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>,
<&cgu JZ4780_CLK_HDMI>;
+ assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>, <0>;
+ assigned-clock-rates = <48000000>, <0>, <27000000>;
So drm-misc-next is based on a slightly older version (not v5.16-rc1
yet), and these lines changed in linux master.
I think it would make sense to merge the DT changes (+ doc) into the
MIPS tree, and the driver changes into drm-misc-next.
@Thomas: Is that OK for you?
Cheers,
-Paul
};
&tcu {
@@ -506,6 +529,12 @@ pins_i2c4: i2c4 {
bias-disable;
};
+ pins_hdmi_ddc: hdmi_ddc {
+ function = "hdmi-ddc";
+ groups = "hdmi-ddc";
+ bias-disable;
+ };
+
pins_nemc: nemc {
function = "nemc";
groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
@@ -536,3 +565,41 @@ pins_mmc1: mmc1 {
bias-disable;
};
};
+
+&hdmi {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_hdmi_ddc>;
+
+ hdmi-5v-supply = <&hdmi_power>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dw_hdmi_in: endpoint {
+ remote-endpoint = <&lcd_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dw_hdmi_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+};
+
+&lcdc0 {
+ status = "okay";
+
+ port {
+ lcd_out: endpoint {
+ remote-endpoint = <&dw_hdmi_in>;
+ };
+ };
+};
--
2.33.0
