Hi Andrew,
On 2021/6/8 上午8:01, Andrew Lunn wrote:
config DWMAC_ROCKCHIP
tristate "Rockchip dwmac support"
- default ARCH_ROCKCHIP
+ default MACH_ROCKCHIP
depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
select MFD_SYSCON
help
@@ -164,7 +176,7 @@ config DWMAC_STI
config DWMAC_STM32
tristate "STM32 DWMAC support"
- default ARCH_STM32
+ default MACH_STM32
It would be good to explain in the commit message why you are changing
these two. It is not obvious.
Apologize for my carelessness, this is left over accidentally when
cleaning up the code, I will remove them in the next version.
+static int jz4775_mac_set_mode(struct plat_stmmacenet_data *plat_dat)
+{
+ struct ingenic_mac *mac = plat_dat->bsp_priv;
+ int val;
+
+ switch (plat_dat->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
+ FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_MII);
+ pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_MII\n");
+ break;
+
+ case PHY_INTERFACE_MODE_GMII:
+ val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
+ FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_GMII);
+ pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_GMII\n");
+ break;
+
+ case PHY_INTERFACE_MODE_RMII:
+ val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
+ FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_RMII);
+ pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_RMII\n");
+ break;
+
+ case PHY_INTERFACE_MODE_RGMII:
What about the other three RGMII modes?
+ case PHY_INTERFACE_MODE_RGMII:
+ val = FIELD_PREP(MACPHYC_TX_SEL_MASK, MACPHYC_TX_SEL_DELAY) |
+ FIELD_PREP(MACPHYC_TX_DELAY_MASK, MACPHYC_TX_DELAY_63_UNIT) |
+ FIELD_PREP(MACPHYC_RX_SEL_MASK, MACPHYC_RX_SEL_ORIGIN) |
+ FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_RGMII);
What exactly does MACPHYC_TX_DELAY_63_UNIT mean here? Ideally, the MAC
should not be adding any RGMII delays. It should however pass mode
through to the PHY, so it can add the delays, if the mode indicates it
should, e.g. PHY_INTERFACE_MODE_RGMII_ID. This is also why you should
be handling all 4 RGMII modes here, not just one.
MACPHYC_TX_DELAY_63_UNIT means set MAC TX clk delay to 63 units (similar to the "tx-delay" in dwmac-rk.c). However, the manual does not clearly describe the time span of one unit, after consulting engineer of Ingenic, I learned that the value is recommended to be set to 63.
I will change it to be similar to the way done in dwmac-rk.c.
Thanks and best regards!
Andrew
