[PATCH v3 02/10] pinctrl: Ingenic: Add support for read the pin configuration of X1830.

[周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>]

Add X1830 support in "ingenic_pinconf_get()", so that it can read the
configuration of X1830 SoC correctly.

Fixes: d7da2a1e4e08 ("pinctrl: Ingenic: Add pinctrl driver for X1830.")

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>
---

Notes:
    v2:
    New patch.
    
    v2->v3:
    1.Add fixes tag.
    2.Adjust the code, simplify the ingenic_pinconf_get() function.

 drivers/pinctrl/pinctrl-ingenic.c | 38 ++++++++++++++++++++++++++++++--------
 1 file changed, 30 insertions(+), 8 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-ingenic.c b/drivers/pinctrl/pinctrl-ingenic.c
index 05dfa0a..1d43b98 100644
--- a/drivers/pinctrl/pinctrl-ingenic.c
+++ b/drivers/pinctrl/pinctrl-ingenic.c
@@ -2109,26 +2109,48 @@ static int ingenic_pinconf_get(struct pinctrl_dev *pctldev,
 	enum pin_config_param param = pinconf_to_config_param(*config);
 	unsigned int idx = pin % PINS_PER_GPIO_CHIP;
 	unsigned int offt = pin / PINS_PER_GPIO_CHIP;
-	bool pull;
+	unsigned int bias;
+	bool pull, pullup, pulldown;
 
-	if (jzpc->info->version >= ID_JZ4770)
-		pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
-	else
-		pull = !ingenic_get_pin_config(jzpc, pin, JZ4740_GPIO_PULL_DIS);
+	if (jzpc->info->version >= ID_X1830) {
+		unsigned int half = PINS_PER_GPIO_CHIP / 2;
+		unsigned int idxh = pin % half * 2;
+
+		if (idx < half)
+			regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
+					X1830_GPIO_PEL, &bias);
+		else
+			regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
+					X1830_GPIO_PEH, &bias);
+
+		bias = (bias >> idxh) & (GPIO_PULL_UP | GPIO_PULL_DOWN);
+
+		pullup = (bias == GPIO_PULL_UP) && (jzpc->info->pull_ups[offt] & BIT(idx));
+		pulldown = (bias == GPIO_PULL_DOWN) && (jzpc->info->pull_downs[offt] & BIT(idx));
+
+	} else {
+		if (jzpc->info->version >= ID_JZ4770)
+			pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
+		else
+			pull = !ingenic_get_pin_config(jzpc, pin, JZ4740_GPIO_PULL_DIS);
+
+		pullup = pull && (jzpc->info->pull_ups[offt] & BIT(idx));
+		pulldown = pull && (jzpc->info->pull_downs[offt] & BIT(idx));
+	}
 
 	switch (param) {
 	case PIN_CONFIG_BIAS_DISABLE:
-		if (pull)
+		if (pullup || pulldown)
 			return -EINVAL;
 		break;
 
 	case PIN_CONFIG_BIAS_PULL_UP:
-		if (!pull || !(jzpc->info->pull_ups[offt] & BIT(idx)))
+		if (!pullup)
 			return -EINVAL;
 		break;
 
 	case PIN_CONFIG_BIAS_PULL_DOWN:
-		if (!pull || !(jzpc->info->pull_downs[offt] & BIT(idx)))
+		if (!pulldown)
 			return -EINVAL;
 		break;
 
-- 
2.7.4