Hello Hauke,
I would like to ask how to write UART nodes of SC16IS752, our CU1000-Neo
board also uses SC16IS752 to expand GPIOs and UARTs, and the bluetooth
module (from AP6212A) is connected to UART expanded by SC16IS752, but I
don't know how to write UART node, so bluetooth cannot be used normally
at present.
Thanks and best regards！
在 2020/8/16 上午12:35, Hauke Mehrtens 写道:
Add NXP SC16IS752IPW SPI-UART controller to device tree.
This controller drives 2 UARTs and 7 LEDs on the board.
Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
---
arch/mips/boot/dts/img/pistachio_marduk.dts | 51 +++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/mips/boot/dts/img/pistachio_marduk.dts b/arch/mips/boot/dts/img/pistachio_marduk.dts
index 633a41954cc0..f4965a484b72 100644
--- a/arch/mips/boot/dts/img/pistachio_marduk.dts
+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
@@ -46,6 +46,46 @@
regulator-max-microvolt = <1800000>;
};
+ /* EXT clock from ca8210 is fed to sc16is752 */
+ ca8210_ext_clk: ca8210-ext-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "ca8210_ext_clock";
+ };
+
+ gpioleds {
+ compatible = "gpio-leds";
+ user1 {
+ label = "marduk:red:user1";
+ gpios = <&sc16is752 0 GPIO_ACTIVE_LOW>;
+ };
+ user2 {
+ label = "marduk:red:user2";
+ gpios = <&sc16is752 1 GPIO_ACTIVE_LOW>;
+ };
+ user3 {
+ label = "marduk:red:user3";
+ gpios = <&sc16is752 2 GPIO_ACTIVE_LOW>;
+ };
+ user4 {
+ label = "marduk:red:user4";
+ gpios = <&sc16is752 3 GPIO_ACTIVE_LOW>;
+ };
+ user5 {
+ label = "marduk:red:user5";
+ gpios = <&sc16is752 4 GPIO_ACTIVE_LOW>;
+ };
+ user6 {
+ label = "marduk:red:user6";
+ gpios = <&sc16is752 5 GPIO_ACTIVE_LOW>;
+ };
+ user7 {
+ label = "marduk:red:user7";
+ gpios = <&sc16is752 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
leds {
compatible = "pwm-leds";
heartbeat {
@@ -95,6 +135,17 @@
extclock-freq = <16000000>;
extclock-gpio = <2>;
};
+
+ sc16is752: sc16is752@1 {
+ compatible = "nxp,sc16is752";
+ reg = <1>;
+ clocks = <&ca8210_ext_clk>;
+ spi-max-frequency = <4000000>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
};
&spfi1 {
