On Thu, 27 Aug 2015, Peter Griffin wrote:
> Signed-off-by: Peter Griffin <peter.griffin@xxxxxxxxxx>
> ---
> .../devicetree/bindings/media/stih407-c8sectpfe.txt | 16 +++++++---------
> 1 file changed, 7 insertions(+), 9 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> index e70d840..5d6438c 100644
> --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> @@ -55,21 +55,20 @@ Example:
> status = "okay";
> reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
> reg-names = "stfe", "stfe-ram";
> - interrupts = <0 34 0>, <0 35 0>;
> + interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
> interrupt-names = "stfe-error-irq", "stfe-idle-irq";
> -
> - pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial",
> - "tsin4-serial", "tsin5-serial";
> -
> + pinctrl-names = "tsin0-serial",
> + "tsin0-parallel",
> + "tsin3-serial",
> + "tsin4-serial",
> + "tsin5-serial";
> pinctrl-0 = <&pinctrl_tsin0_serial>;
> pinctrl-1 = <&pinctrl_tsin0_parallel>;
> pinctrl-2 = <&pinctrl_tsin3_serial>;
> pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
> pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
> -
> clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
> - clock-names = "stfe";
> -
> + clock-names = "c8sectpfe";
Are you sure you even need this property? I'm thinking that *-names
properties are *usually* only required if there are more than one in a
single property.
> /* tsin0 is TSA on NIMA */
> tsin0: port@0 {
> tsin-num = <0>;
> @@ -78,7 +77,6 @@ Example:
> reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
> dvb-card = <STV0367_TDA18212_NIMA_1>;
> };
> -
My personal preference is to have a '\n' between nodes.
> tsin3: port@3 {
> tsin-num = <3>;
> serial-not-parallel;
But these comments are pretty trivial, so agree or not, or fix-up or
not, it's that big of a deal.
Either way,
Acked-by: Lee Jones <lee.jones@xxxxxxxxxx>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
