Hi Jacek, On Mon, Mar 30, 2015 at 09:36:37AM +0200, Jacek Anaszewski wrote: > Hi Sakari, > > On 03/28/2015 11:55 PM, Sakari Ailus wrote: > >On Fri, Mar 27, 2015 at 02:49:38PM +0100, Jacek Anaszewski wrote: > >>This patch adds device tree binding documentation for > >>the flash cell of the Maxim max77693 multifunctional device. > >> > >>Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx> > >>Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx> > >>Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx> > >>Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx> > >>Cc: Lee Jones <lee.jones@xxxxxxxxxx> > >>Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx> > >>Cc: Bryan Wu <cooloney@xxxxxxxxx> > >>Cc: Richard Purdie <rpurdie@xxxxxxxxx> > >>--- > >> Documentation/devicetree/bindings/mfd/max77693.txt | 61 ++++++++++++++++++++ > >> 1 file changed, 61 insertions(+) > >> > >>diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt > >>index 38e6440..15c546ea 100644 > >>--- a/Documentation/devicetree/bindings/mfd/max77693.txt > >>+++ b/Documentation/devicetree/bindings/mfd/max77693.txt > >>@@ -76,7 +76,53 @@ Optional properties: > >> Valid values: 4300000, 4700000, 4800000, 4900000 > >> Default: 4300000 > >> > >>+- led : the LED submodule device node > >>+ > >>+There are two LED outputs available - FLED1 and FLED2. Each of them can > >>+control a separate LED or they can be connected together to double > >>+the maximum current for a single connected LED. One LED is represented > >>+by one child node. > >>+ > >>+Required properties: > >>+- compatible : Must be "maxim,max77693-led". > >>+ > >>+Optional properties: > >>+- maxim,trigger-type : Flash trigger type. > >>+ Possible trigger types: > >>+ LEDS_TRIG_TYPE_EDGE (0) - Rising edge of the signal triggers > >>+ the flash, > >>+ LEDS_TRIG_TYPE_LEVEL (1) - Strobe pulse length controls duration > >>+ of the flash. > >>+- maxim,boost-mode : > >>+ In boost mode the device can produce up to 1.2A of total current > >>+ on both outputs. The maximum current on each output is reduced > >>+ to 625mA then. If not enabled explicitly, boost setting defaults to > >>+ LEDS_BOOST_FIXED in case both current sources are used. > >>+ Possible values: > >>+ LEDS_BOOST_OFF (0) - no boost, > >>+ LEDS_BOOST_ADAPTIVE (1) - adaptive mode, > >>+ LEDS_BOOST_FIXED (2) - fixed mode. > >>+- maxim,boost-mvout : Output voltage of the boost module in millivolts. > > > >What are the possible values for this? > > maxim,boost-mvout : Output voltage of the boost module in millivolts > Range: 3300 - 5500 Could you please add that? > > Do you think it is necessary to mention also allowed step for all the > values? That's a good question. They probably are more or less visible in the driver code. I think I'd document them here, but I'm fine with not adding them as well. You probably wouldn't be able to meaningfully use the chip without the datasheet anyway. > >Is the datasheet publicly available btw.? > > I have an access only to the non-public one. I googled a bit, couldn't find anything relevant immediately at least. -- Regards, Sakari Ailus e-mail: sakari.ailus@xxxxxx XMPP: sailus@xxxxxxxxxxxxxx -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
