I'm currently running on ArchLinux
[ 0.000000] Linux version 3.18.6-1-ARCH (cdale@huntsman) (gcc version
4.9.2 20150204 (prerelease) (GCC) ) #2 SMP PREEMPT Sun Mar 8 10:00:24
AEST 2015
On boot the card is detected by the kernel:
[ 13.575736] usb 5-1: dvb_usb_v2: found a 'Leadtek WinFast DTV2000DS
Plus' in warm state
[ 13.625489] usb 5-1: dvb_usb_v2: will pass the complete MPEG2
transport stream to the software demuxer
[ 13.625495] DVB: registering new adapter (Leadtek WinFast DTV2000DS Plus)
[ 13.625630] i2c i2c-9: Added multiplexed i2c bus 10
[ 13.628355] i2c i2c-9: Added multiplexed i2c bus 11
[ 13.628357] usb 5-1: DVB: registering adapter 0 frontend 0 (Realtek
RTL2832 (DVB-T))...
[ 13.636492] fc0013: Fitipower FC0013 successfully attached.
[ 13.639454] media: Linux media interface: v0.10
[ 13.642166] Linux video capture interface: v2.00
[ 13.645296] usb 5-1: Registered as swradio0
[ 13.645298] i2c i2c-9: rtl2832_sdr: Realtek RTL2832 SDR attached
[ 13.645299] usb 5-1: rtl2832_sdr: SDR API is still slightly
experimental and functionality changes may follow
[ 13.680959] Registered IR keymap rc-leadtek-y04g0051
[ 13.681023] input: Leadtek WinFast DTV2000DS Plus as
/devices/pci0000:00/0000:00:1c.5/0000:05:00.0/0000:06:01.2/usb5/5-1/rc/rc0/input18
[ 13.681110] rc0: Leadtek WinFast DTV2000DS Plus as
/devices/pci0000:00/0000:00:1c.5/0000:05:00.0/0000:06:01.2/usb5/5-1/rc/rc0
[ 13.681943] IR RC5(x/sz) protocol handler initialized
[ 13.681951] IR NEC protocol handler initialized
[ 13.682226] IR RC6 protocol handler initialized
[ 13.682869] IR Sony protocol handler initialized
[ 13.682976] IR JVC protocol handler initialized
[ 13.683088] IR SANYO protocol handler initialized
[ 13.683643] IR Sharp protocol handler initialized
[ 13.684296] usb 5-1: dvb_usb_v2: schedule remote query interval to
400 msecs
[ 13.684415] lirc_dev: IR Remote Control driver registered, major 246
[ 13.684492] IR XMP protocol handler initialized
[ 13.684688] input: MCE IR Keyboard/Mouse (dvb_usb_rtl28xxu) as
/devices/virtual/input/input19
[ 13.684996] IR MCE Keyboard/mouse protocol handler initialized
[ 13.685031] rc rc0: lirc_dev: driver ir-lirc-codec (dvb_usb_rtl28xxu)
registered at minor = 0
[ 13.685033] IR LIRC bridge handler initialized
[ 13.700080] usb 5-1: dvb_usb_v2: 'Leadtek WinFast DTV2000DS Plus'
successfully initialized and connected
[ 13.700095] usb 5-2: dvb_usb_v2: found a 'Leadtek WinFast DTV2000DS
Plus' in warm state
[ 13.741247] usb 5-2: dvb_usb_v2: will pass the complete MPEG2
transport stream to the software demuxer
[ 13.741253] DVB: registering new adapter (Leadtek WinFast DTV2000DS Plus)
[ 13.741474] i2c i2c-12: Added multiplexed i2c bus 13
[ 13.744120] i2c i2c-12: Added multiplexed i2c bus 14
[ 13.744123] usb 5-2: DVB: registering adapter 1 frontend 0 (Realtek
RTL2832 (DVB-T))...
[ 13.744164] fc0013: Fitipower FC0013 successfully attached.
[ 13.744413] usb 5-2: Registered as swradio1
[ 13.744415] i2c i2c-12: rtl2832_sdr: Realtek RTL2832 SDR attached
[ 13.744416] usb 5-2: rtl2832_sdr: SDR API is still slightly
experimental and functionality changes may follow
[ 13.751351] Registered IR keymap rc-leadtek-y04g0051
[ 13.751403] input: Leadtek WinFast DTV2000DS Plus as
/devices/pci0000:00/0000:00:1c.5/0000:05:00.0/0000:06:01.2/usb5/5-2/rc/rc1/input20
[ 13.751438] rc1: Leadtek WinFast DTV2000DS Plus as
/devices/pci0000:00/0000:00:1c.5/0000:05:00.0/0000:06:01.2/usb5/5-2/rc/rc1
[ 13.751486] input: MCE IR Keyboard/Mouse (dvb_usb_rtl28xxu) as
/devices/virtual/input/input21
[ 13.751732] rc rc1: lirc_dev: driver ir-lirc-codec (dvb_usb_rtl28xxu)
registered at minor = 1
[ 13.751734] usb 5-2: dvb_usb_v2: schedule remote query interval to
400 msecs
[ 13.763740] usb 5-2: dvb_usb_v2: 'Leadtek WinFast DTV2000DS Plus'
successfully initialized and connected
[ 13.763755] usbcore: registered new interface driver dvb_usb_rtl28xxu
Following that, everything just worked when using mythtv. Found all the
channels just fine. I haven't played with any SDR stuff yet, though it
was something I wanted to look at.
I've just tried to use "scan" now, and I do get a segfault from it. So I
might need to take a look at what's going on there.
[252013.059718] scan[20552]: segfault at ffffffff ip 00007fbb2bbf5ca2 sp
00007fffa80956b0 error 4 in libc-2.21.so[7fbb2bbad000+199000]
Kind of useless until I build with some debug symbols...
I do get this error from mythbackend every 5 minutes. Not sure if it's
related.
mythbackend[1513]: 2015-03-13 20:05:23.284218 E
DVBChan[3](/dev/dvb/adapter1/frontend0): Getting Frontend uncorrected
block count failed.
mythbackend[1513]: eno: Operation not supported (95)
mythbackend[1513]: 2015-03-13 20:05:23.284225 W
DVBSigMon[3](/dev/dvb/adapter1/frontend0): Cannot count Uncorrected Blocks
mythbackend[1513]: eno: Operation not supported (95)
Never seen that error happen on adapter0. Only adapter1.
I'm going to play around over the next week and see if I can find out
why scan is segfaulting for me.
Christian
On 13/03/15 20:07, Vincent McIntyre wrote:
On Mon, Mar 09, 2015 at 03:19:01PM +1000, Christian Dale wrote:
Add Leadtek WinFast DTV2000DS Plus device based on Realtek RTL2832U.
I have not tested the remote, but it is the Y04G0051 model.
Thanks for doing this Christian. I have one of these cards also, 0x6f12.
I wrote the same patch some time ago and it is not working for me.
Can you give a few details of what kernel you tested on etc?
I am testing on ubuntu 14.04 LTS
[ 0.000000] Linux version 3.13.0-45-generic (buildd@kissel) (gcc
version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #74-Ubuntu SMP Tue Jan 13
19:37:48 UTC 2015 (Ubuntu 3.13.0-45.74-generic 3.13.11-ckt13)
The symptom I have is when I try to tune with 'scan'
from dvb-apps, the program wedges and I get this in dmesg:
[ 163.138982] fc0013: fc0013_set_params: failed: -22
[ 164.246233] fc0013: fc0013_set_params: failed: -22
[ 165.167758] fc0013: fc0013_set_params: failed: -22
[ 166.250280] fc0013: fc0013_set_params: failed: -22
[ 167.196580] fc0013: fc0013_set_params: failed: -22
[ 168.286208] fc0013: fc0013_set_params: failed: -22
...
kind regards
Vince
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
