On Fri, 09 Jan 2015, Jacek Anaszewski wrote:
> This patch adds device tree binding documentation for
> the flash cell of the Maxim max77693 multifunctional device.
>
> Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> Cc: Lee Jones <lee.jones@xxxxxxxxxx>
> Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
> Cc: Bryan Wu <cooloney@xxxxxxxxx>
> Cc: Richard Purdie <rpurdie@xxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Pawel Moll <pawel.moll@xxxxxxx>
> Cc: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
> Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/mfd/max77693.txt | 69 ++++++++++++++++++++
> 1 file changed, 69 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
> index 01e9f30..ef184f0 100644
> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
> +++ b/Documentation/devicetree/bindings/mfd/max77693.txt
> @@ -41,7 +41,52 @@ Optional properties:
> To get more informations, please refer to documentaion.
> [*] refer Documentation/devicetree/bindings/pwm/pwm.txt
>
> +- led : the LED submodule device node
> +
> +There are two led outputs available - fled1 and fled2. Each of them can
> +control a separate led or they can be connected together to double
> +the maximum current for a single connected led. One led is represented
> +by one child node.
> +
> +Required properties:
> +- compatible : Must be "maxim,max77693-led".
> +
> +Optional properties:
> +- maxim,trigger-type : Flash trigger type.
> + Possible trigger types:
> + MAX77693_LED_TRIG_TYPE_EDGE - Rising edge of the signal triggers
> + the flash,
> + MAX77693_LED_TRIG_TYPE_LEVEL - Strobe pulse length controls
> + duration of the flash.
I think you should represent the proper values here instead of the
defines.
> +- maxim,boost-mode :
> + In boost mode the device can produce up to 1.2A of total current
> + on both outputs. The maximum current on each output is reduced
> + to 625mA then. If not enabled explicitly, boost setting defaults to
> + MAX77693_LED_BOOST_FIXED in case both current sources are used.
> + Possible values:
> + MAX77693_LED_BOOST_OFF - no boost,
> + MAX77693_LED_BOOST_ADAPTIVE - adaptive mode,
> + MAX77693_LED_BOOST_FIXED - fixed mode.
Same here.
> +- maxim,boost-vout : Output voltage of the boost module in millivolts.
-mvout?
-microvout?
> +- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
> + if chip estimates that system voltage could drop below this level due
> + to flash power consumption.
mvsys?
microvsys?
> +Required properties of the LED child node:
> +- label : see Documentation/devicetree/bindings/leds/common.txt
> +- led-sources : see Documentation/devicetree/bindings/leds/common.txt
> +
> +Optional properties of the LED child node:
> +- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> + Range: 15625 - 250000
> +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> + Range: 15625 - 1000000
> +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
> + Range: 62500 - 1000000
> +
> Example:
> +#include <dt-bindings/mfd/max77693.h>
> +
> max77693@66 {
> compatible = "maxim,max77693";
> reg = <0x66>;
> @@ -73,4 +118,28 @@ Example:
> pwms = <&pwm 0 40000 0>;
> pwm-names = "haptic";
> };
> +
> + led {
> + compatible = "maxim,max77693-led";
> + maxim,trigger-type = <MAX77693_LED_TRIG_TYPE_LEVEL>;
> + maxim,boost-mode = <MAX77693_LED_BOOST_FIXED>;
> + maxim,boost-vout = <5000>;
> + maxim,vsys-min = <2400>;
> +
> + camera1_flash: led1 {
> + label = "max77693-flash1";
> + led-sources = <1 0>;
> + max-microamp = <250000>;
> + flash-max-microamp = <625000>;
> + flash-timeout-us = <1000000>;
> + };
> +
> + camera2_flash: led2 {
> + label = "max77693-flash2";
> + led-sources = <0 1>;
> + max-microamp = <250000>;
> + flash-max-microamp = <625000>;
> + flash-timeout-us = <1000000>;
> + };
> + };
> };
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
