This patch uses DT in order to parse addresses for dummy devices of adv7604.
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I²C ports. Each map has it own I²C address and acts
as a standard slave device on the I²C bus.
If nothing is defined, it uses default addresses.
The main prupose is using two adv76xx on the same i2c bus.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx>
---
.../devicetree/bindings/media/i2c/adv7604.txt | 17 +++++-
drivers/media/i2c/adv7604.c | 60 ++++++++++++++--------
2 files changed, 55 insertions(+), 22 deletions(-)
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
index c27cede..8486b5c 100644
--- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -10,8 +10,12 @@ Required Properties:
- compatible: Must contain one of the following
- "adi,adv7611" for the ADV7611
+ - "adi,adv7604" for the ADV7604
- - reg: I2C slave address
+ - reg: I2C slave addresses
+ The ADV7604 has thirteen 256-byte maps that can be accessed via the main
+ I²C ports. Each map has it own I²C address and acts
+ as a standard slave device on the I²C bus.
- hpd-gpios: References to the GPIOs that control the HDMI hot-plug
detection pins, one per HDMI input. The active flag indicates the GPIO
@@ -32,6 +36,12 @@ The digital output port node must contain at least one endpoint.
Optional Properties:
- reset-gpios: Reference to the GPIO connected to the device's reset pin.
+ - reg-names : Names of maps with programmable addresses.
+ It can contain any map needing another address than default one.
+ Possible maps names are :
+ADV7604 : "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", "rep",
+ "edid", "hdmi", "test", "cp", "vdp"
+ADV7611 : "main", "cec", "infoframe", "afe", "rep", "edid", "hdmi", "cp"
Optional Endpoint Properties:
@@ -50,7 +60,10 @@ Example:
hdmi_receiver@4c {
compatible = "adi,adv7611";
- reg = <0x4c>;
+ /* edid page will be accessible @ 0x66 on i2c bus */
+ /* other maps keep their default addresses */
+ reg = <0x4c 0x66>;
+ reg-names = "main", "edid";
reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
index d4fa213..56037dd 100644
--- a/drivers/media/i2c/adv7604.c
+++ b/drivers/media/i2c/adv7604.c
@@ -326,6 +326,22 @@ static const struct adv7604_video_standards adv7604_prim_mode_hdmi_gr[] = {
{ },
};
+static const char const *adv7604_secondary_names[] = {
+ "main", /* ADV7604_PAGE_IO */
+ "avlink", /* ADV7604_PAGE_AVLINK */
+ "cec", /* ADV7604_PAGE_CEC */
+ "infoframe", /* ADV7604_PAGE_INFOFRAME */
+ "esdp", /* ADV7604_PAGE_ESDP */
+ "dpp", /* ADV7604_PAGE_DPP */
+ "afe", /* ADV7604_PAGE_AFE */
+ "rep", /* ADV7604_PAGE_REP */
+ "edid", /* ADV7604_PAGE_EDID */
+ "hdmi", /* ADV7604_PAGE_HDMI */
+ "test", /* ADV7604_PAGE_TEST */
+ "cp", /* ADV7604_PAGE_CP */
+ "vdp" /* ADV7604_PAGE_VDP */
+};
+
/* ----------------------------------------------------------------------- */
static inline struct adv7604_state *to_state(struct v4l2_subdev *sd)
@@ -2528,13 +2544,31 @@ static void adv7604_unregister_clients(struct adv7604_state *state)
}
static struct i2c_client *adv7604_dummy_client(struct v4l2_subdev *sd,
- u8 addr, u8 io_reg)
+ unsigned int i)
{
struct i2c_client *client = v4l2_get_subdevdata(sd);
+ struct adv7604_platform_data *pdata = client->dev.platform_data;
+ unsigned int io_reg = 0xf2 + i;
+ unsigned int default_addr = io_read(sd, io_reg) >> 1;
+ struct i2c_client *new_client;
+
+ if (IS_ENABLED(CONFIG_OF)) {
+ /* Try to find it in DT */
+ new_client = i2c_new_secondary_device(client,
+ adv7604_secondary_names[i], default_addr);
+ } else if (pdata) {
+ if (pdata->i2c_addresses[i])
+ new_client = i2c_new_dummy(client->adapter,
+ pdata->i2c_addresses[i]);
+ else
+ new_client = i2c_new_dummy(client->adapter,
+ default_addr);
+ }
- if (addr)
- io_write(sd, io_reg, addr << 1);
- return i2c_new_dummy(client->adapter, io_read(sd, io_reg) >> 1);
+ if (new_client)
+ io_write(sd, io_reg, new_client->addr << 1);
+
+ return new_client;
}
static const struct adv7604_reg_seq adv7604_recommended_settings_afe[] = {
@@ -2677,6 +2711,7 @@ MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id);
static struct of_device_id adv7604_of_id[] __maybe_unused = {
{ .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] },
+ { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] },
{ }
};
MODULE_DEVICE_TABLE(of, adv7604_of_id);
@@ -2717,20 +2752,6 @@ static int adv7604_parse_dt(struct adv7604_state *state)
/* Disable the interrupt for now as no DT-based board uses it. */
state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED;
- /* Use the default I2C addresses. */
- state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42;
- state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40;
- state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e;
- state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38;
- state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c;
- state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26;
- state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32;
- state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36;
- state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34;
- state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30;
- state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22;
- state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24;
-
/* Hardcode the remaining platform data fields. */
state->pdata.disable_pwrdnb = 0;
state->pdata.disable_cable_det_rst = 0;
@@ -2891,8 +2912,7 @@ static int adv7604_probe(struct i2c_client *client,
continue;
state->i2c_clients[i] =
- adv7604_dummy_client(sd, state->pdata.i2c_addresses[i],
- 0xf2 + i);
+ adv7604_dummy_client(sd, i);
if (state->i2c_clients[i] == NULL) {
err = -ENOMEM;
v4l2_err(sd, "failed to create i2c client %u\n", i);
--
2.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
