It is OK.
Acked-by: Antti Palosaari <crope@xxxxxx>
Reviewed-by: Antti Palosaari <crope@xxxxxx>
Antti
On 08/11/2014 07:22 AM, nibble.max wrote:
Add ts clock and clock polarity, lnb set voltage and lnb control pin.
Signed-off-by: Nibble Max <nibble.max@xxxxxxxxx>
---
drivers/media/dvb-frontends/m88ds3103.c | 72 ++++++++++++++++++++-------------
drivers/media/dvb-frontends/m88ds3103.h | 35 +++++++++++++---
2 files changed, 75 insertions(+), 32 deletions(-)
diff --git a/drivers/media/dvb-frontends/m88ds3103.c b/drivers/media/dvb-frontends/m88ds3103.c
index dfe0c2f..238b04e 100644
--- a/drivers/media/dvb-frontends/m88ds3103.c
+++ b/drivers/media/dvb-frontends/m88ds3103.c
@@ -247,7 +247,7 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
u8 u8tmp, u8tmp1, u8tmp2;
u8 buf[2];
u16 u16tmp, divide_ratio;
- u32 tuner_frequency, target_mclk, ts_clk;
+ u32 tuner_frequency, target_mclk;
s32 s32tmp;
dev_dbg(&priv->i2c->dev,
"%s: delivery_system=%d modulation=%d frequency=%d symbol_rate=%d inversion=%d pilot=%d rolloff=%d\n",
@@ -316,9 +316,6 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
target_mclk = 144000;
break;
case M88DS3103_TS_PARALLEL:
- case M88DS3103_TS_PARALLEL_12:
- case M88DS3103_TS_PARALLEL_16:
- case M88DS3103_TS_PARALLEL_19_2:
case M88DS3103_TS_CI:
if (c->symbol_rate < 18000000)
target_mclk = 96000;
@@ -352,33 +349,17 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
switch (priv->cfg->ts_mode) {
case M88DS3103_TS_SERIAL:
u8tmp1 = 0x00;
- ts_clk = 0;
- u8tmp = 0x46;
+ u8tmp = 0x06;
break;
case M88DS3103_TS_SERIAL_D7:
u8tmp1 = 0x20;
- ts_clk = 0;
- u8tmp = 0x46;
+ u8tmp = 0x06;
break;
case M88DS3103_TS_PARALLEL:
- ts_clk = 24000;
- u8tmp = 0x42;
- break;
- case M88DS3103_TS_PARALLEL_12:
- ts_clk = 12000;
- u8tmp = 0x42;
- break;
- case M88DS3103_TS_PARALLEL_16:
- ts_clk = 16000;
- u8tmp = 0x42;
- break;
- case M88DS3103_TS_PARALLEL_19_2:
- ts_clk = 19200;
- u8tmp = 0x42;
+ u8tmp = 0x02;
break;
case M88DS3103_TS_CI:
- ts_clk = 6000;
- u8tmp = 0x43;
+ u8tmp = 0x03;
break;
default:
dev_dbg(&priv->i2c->dev, "%s: invalid ts_mode\n", __func__);
@@ -386,6 +367,9 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
goto err;
}
+ if (priv->cfg->ts_clk_pol)
+ u8tmp |= 0x40;
+
/* TS mode */
ret = m88ds3103_wr_reg(priv, 0xfd, u8tmp);
if (ret)
@@ -399,8 +383,8 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
goto err;
}
- if (ts_clk) {
- divide_ratio = DIV_ROUND_UP(target_mclk, ts_clk);
+ if (priv->cfg->ts_clk) {
+ divide_ratio = DIV_ROUND_UP(target_mclk, priv->cfg->ts_clk);
u8tmp1 = divide_ratio / 2;
u8tmp2 = DIV_ROUND_UP(divide_ratio, 2);
} else {
@@ -411,7 +395,7 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
dev_dbg(&priv->i2c->dev,
"%s: target_mclk=%d ts_clk=%d divide_ratio=%d\n",
- __func__, target_mclk, ts_clk, divide_ratio);
+ __func__, target_mclk, priv->cfg->ts_clk, divide_ratio);
u8tmp1--;
u8tmp2--;
@@ -1053,6 +1037,39 @@ err:
return ret;
}
+static int m88ds3103_set_voltage(struct dvb_frontend *fe,
+ fe_sec_voltage_t voltage)
+{
+ struct m88ds3103_priv *priv = fe->demodulator_priv;
+ u8 data;
+
+ m88ds3103_rd_reg(priv, 0xa2, &data);
+
+ data &= ~0x03; /* bit0 V/H, bit1 off/on */
+ if (priv->cfg->lnb_en_pol)
+ data |= 0x02;
+
+ switch (voltage) {
+ case SEC_VOLTAGE_18:
+ if (priv->cfg->lnb_hv_pol == 0)
+ data |= 0x01;
+ break;
+ case SEC_VOLTAGE_13:
+ if (priv->cfg->lnb_hv_pol)
+ data |= 0x01;
+ break;
+ case SEC_VOLTAGE_OFF:
+ if (priv->cfg->lnb_en_pol)
+ data &= ~0x02;
+ else
+ data |= 0x02;
+ break;
+ }
+ m88ds3103_wr_reg(priv, 0xa2, data);
+
+ return 0;
+}
+
static int m88ds3103_diseqc_send_master_cmd(struct dvb_frontend *fe,
struct dvb_diseqc_master_cmd *diseqc_cmd)
{
@@ -1370,6 +1387,7 @@ static struct dvb_frontend_ops m88ds3103_ops = {
.diseqc_send_burst = m88ds3103_diseqc_send_burst,
.set_tone = m88ds3103_set_tone,
+ .set_voltage = m88ds3103_set_voltage,
};
MODULE_AUTHOR("Antti Palosaari <crope@xxxxxx>");
diff --git a/drivers/media/dvb-frontends/m88ds3103.h b/drivers/media/dvb-frontends/m88ds3103.h
index bbb7e3a..9b3b496 100644
--- a/drivers/media/dvb-frontends/m88ds3103.h
+++ b/drivers/media/dvb-frontends/m88ds3103.h
@@ -47,14 +47,23 @@ struct m88ds3103_config {
*/
#define M88DS3103_TS_SERIAL 0 /* TS output pin D0, normal */
#define M88DS3103_TS_SERIAL_D7 1 /* TS output pin D7 */
-#define M88DS3103_TS_PARALLEL 2 /* 24 MHz, normal */
-#define M88DS3103_TS_PARALLEL_12 3 /* 12 MHz */
-#define M88DS3103_TS_PARALLEL_16 4 /* 16 MHz */
-#define M88DS3103_TS_PARALLEL_19_2 5 /* 19.2 MHz */
-#define M88DS3103_TS_CI 6 /* 6 MHz */
+#define M88DS3103_TS_PARALLEL 2 /* TS Parallel mode */
+#define M88DS3103_TS_CI 3 /* TS CI Mode */
u8 ts_mode;
/*
+ * TS clk in KHz
+ * Default: 0.
+ */
+ u32 ts_clk;
+
+ /*
+ * TS clk polarity.
+ * Default: 0. 1-active at falling edge; 0-active at rising edge.
+ */
+ u8 ts_clk_pol:1;
+
+ /*
* spectrum inversion
* Default: 0
*/
@@ -86,6 +95,22 @@ struct m88ds3103_config {
* Default: none, must set
*/
u8 agc;
+
+ /*
+ * LNB H/V pin polarity
+ * Default: 0.
+ * 1: pin high set to VOLTAGE_13, pin low to set VOLTAGE_18.
+ * 0: pin high set to VOLTAGE_18, pin low to set VOLTAGE_13.
+ */
+ u8 lnb_hv_pol:1;
+
+ /*
+ * LNB enable pin polarity
+ * Default: 0.
+ * 1: pin high to enable, pin low to disable.
+ * 0: pin high to disable, pin low to enable.
+ */
+ u8 lnb_en_pol:1;
};
/*
--
http://palosaari.fi/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
