I have an capture card with two bt878A fusion chip and 16 imputs. Linux don't recognize and cannot get to work. How can do to resolve that? This is message from lspci (i put only for one decive) 12:0c.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 132 (4000ns min, 10000ns max) Interrupt: pin A routed to IRQ 22 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data pcilib: sysfs_read_vpd: read failed: Connection timed out Not readable Capabilities: [4c] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: bttv With regspy on indows i have this: BT878 Card [0]: Vendor ID: 0x109e Device ID: 0x036e Subsystem ID: 0x00000000 ================================================================================= BT878 Card - Register Dump: BT848_IFORM: 49 (01001001) BT848_FCNTR: 54 (01010100) BT848_PLL_F_LO: 00 (00000000) BT848_PLL_F_HI: 00 (00000000) BT848_PLL_XCI: 00 (00000000) BT848_TGCTRL: 00 (00000000) BT848_TDEC: 00 (00000000) BT848_E_CROP: 12 (00010010) BT848_O_CROP: 12 (00010010) BT848_E_VDELAY_LO: 1a (00011010) BT848_O_VDELAY_LO: 1a (00011010) BT848_E_VACTIVE_LO: e0 (11100000) BT848_O_VACTIVE_LO: e0 (11100000) BT848_E_HDELAY_LO: 82 (10000010) BT848_O_HDELAY_LO: 82 (10000010) BT848_E_HACTIVE_LO: d0 (11010000) BT848_O_HACTIVE_LO: d0 (11010000) BT848_E_HSCALE_HI: 00 (00000000) BT848_O_HSCALE_HI: 00 (00000000) BT848_E_HSCALE_LO: c1 (11000001) BT848_O_HSCALE_LO: c1 (11000001) BT848_BRIGHT: 14 (00010100) BT848_E_CONTROL: 00 (00000000) BT848_O_CONTROL: 00 (00000000) BT848_CONTRAST_LO: cf (11001111) BT848_SAT_U_LO: fe (11111110) BT848_SAT_V_LO: db (11011011) BT848_HUE: 00 (00000000) BT848_E_SCLOOP: 40 (01000000) BT848_O_SCLOOP: 40 (01000000) BT848_WC_UP: cf (11001111) BT848_WC_DOWN: 7f (01111111) BT848_VTOTAL_LO: 00 (00000000) BT848_VTOTAL_HI: 00 (00000000) BT848_DVSIF: 00 (00000000) BT848_OFORM: 06 (00000110) BT848_E_VSCALE_HI: 60 (01100000) BT848_O_VSCALE_HI: 60 (01100000) BT848_E_VSCALE_LO: 00 (00000000) BT848_O_VSCALE_LO: 00 (00000000) BT848_ADC: 41 (01000001) BT848_E_VTC: 00 (00000000) BT848_O_VTC: 00 (00000000) BT848_COLOR_FMT: 44 (01000100) BT848_COLOR_CTL: 00 (00000000) BT848_CAP_CTL: 00 (00000000) BT848_VBI_PACK_SIZE: 90 (10010000) BT848_VBI_PACK_DEL: 01 (00000001) BT848_INT_MASK: 00000000 (00000000 00000000 00000000 00000000) BT848_GPIO_OUT_EN: 0000b8ff (00000000 00000000 10111000 11111111) BT848_GPIO_OUT_EN_HIBYTE: 00000000 (00000000 00000000 00000000 00000000) BT848_GPIO_DATA: 00ffcd00 (00000000 11111111 11001101 00000000) BT848_RISC_STRT_ADD: 00000000 (00000000 00000000 00000000 00000000) BT848_GPIO_DMA_CTL: 00fc (00000000 11111100) end of dump and with btspy: ### BtSpy Report ### General information: Name:Broktree Chip: Bt878 , Rev: 0x00 Subsystem: 0x00000000 Vendor: Gammagraphx, Inc. Values to MUTE audio: Mute_GPOE : 0x00b8ff Mute_GPDATA: 0x008803 Has TV Tuner: No Number of Composite Ins: 2 Composite in #1 Composite1_Mux : 2 Composite1_GPOE : 0x00b8ff Composite1_GPDATA: 0x008803 Composite in #2 Composite2_Mux : 2 Composite2_GPOE : 0x00b8ff Composite2_GPDATA: 0x008803 Has SVideo: Yes SVideo_Mux : 2 SVideo_GPOE : 0x00b8ff SVideo_GPDATA: 0x008803 Has Radio: No I try't all card numbers when load bttv module but in the best case only one camera i can see per device on channel 0 (using zoneminder). Because is a tunerless card, probably my problem is to make tuner on chip to work. Any advice? -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
