OK I have picture in mythtv now, but it's very glitchy (lines in video, bursts of high pitched tone in audio). In fact it is behaving much like the dib0700 based adapter that I replaced with the express2 adapter because I thought it had died. Could there been a regression somewhere? I'll check the git archives but I don't know when it broke - somewhere between kernel 3.2.x and 3.14.x. Alternatively the dib0700 adapter could actually be dead and maybe this is something different...
The change I made was to set the output mode to OUTMODE_MPEG2_SERIAL after copying the code from the USB dib7070 based adapter.
The "Leadtek Research, Inc. WinFast DTV Dongle Gold" (0413:6029) that I am still using works fine so I don't think it's a physical reception problem unless the signal has gotten suddenly really poor.
Any suggestions?
My current patch follows this email. It's a bit messy because the dib7070 stuff is tied fairly closely to the usb code so there is a bit of duplication. And there is some state required and I don't know that I've put it in the right place (sec_priv).
Thanks
James
diff --git a/drivers/media/dvb-frontends/dib7000p.h b/drivers/media/dvb-frontends/dib7000p.h
index 1fea0e9..4d1dbca 100644
--- a/drivers/media/dvb-frontends/dib7000p.h
+++ b/drivers/media/dvb-frontends/dib7000p.h
@@ -64,6 +64,7 @@ struct dib7000p_ops {
int (*get_adc_power)(struct dvb_frontend *fe);
int (*slave_reset)(struct dvb_frontend *fe);
struct dvb_frontend *(*init)(struct i2c_adapter *i2c_adap, u8 i2c_addr, struct dib7000p_config *cfg);
+ int (*set_param_save)(struct dvb_frontend *fe);
};
#if IS_ENABLED(CONFIG_DVB_DIB7000P)
diff --git a/drivers/media/pci/cx23885/cx23885-cards.c b/drivers/media/pci/cx23885/cx23885-cards.c
index 79f20c8..9ca8855 100644
--- a/drivers/media/pci/cx23885/cx23885-cards.c
+++ b/drivers/media/pci/cx23885/cx23885-cards.c
@@ -649,7 +649,12 @@ struct cx23885_board cx23885_boards[] = {
CX25840_NONE1_CH3,
.amux = CX25840_AUDIO6,
} },
- }
+ },
+ [CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2] = {
+ .name = "DViCO FusionHDTV DVB-T Dual Express2",
+ .portb = CX23885_MPEG_DVB,
+ .portc = CX23885_MPEG_DVB,
+ },
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -897,6 +902,10 @@ struct cx23885_subid cx23885_subids[] = {
.subvendor = 0x1461,
.subdevice = 0xd939,
.card = CX23885_BOARD_AVERMEDIA_HC81R,
+ }, {
+ .subvendor = 0x18ac,
+ .subdevice = 0xdb98,
+ .card = CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2,
},
};
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -1137,6 +1146,7 @@ int cx23885_tuner_callback(void *priv, int component, int command, int arg)
break;
case CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP:
case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
+ case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2:
/* Two identical tuners on two different i2c buses,
* we need to reset the correct gpio. */
if (port->nr == 1)
@@ -1280,6 +1290,7 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
cx_set(GP0_IO, 0x000f000f);
break;
case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
+ case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2:
/* GPIO-0 portb xc3028 reset */
/* GPIO-1 portb zl10353 reset */
/* GPIO-2 portc xc3028 reset */
@@ -1585,6 +1596,7 @@ int cx23885_ir_init(struct cx23885_dev *dev)
ir_rxtx_pin_cfg_count, ir_rxtx_pin_cfg);
break;
case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
+ case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2:
request_module("ir-kbd-i2c");
break;
}
@@ -1720,6 +1732,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
break;
case CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP:
case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
+ case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2:
ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
ts2->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c
index d037459..89d6c54 100644
--- a/drivers/media/pci/cx23885/cx23885-dvb.c
+++ b/drivers/media/pci/cx23885/cx23885-dvb.c
@@ -44,6 +44,7 @@
#include "tuner-xc2028.h"
#include "tuner-simple.h"
#include "dib7000p.h"
+#include "dib0070.h"
#include "dibx000_common.h"
#include "zl10353.h"
#include "stv0900.h"
@@ -746,6 +747,119 @@ static int netup_altera_fpga_rw(void *device, int flag, int data, int read)
return 0;
};
+static int dib7070_tuner_reset(struct dvb_frontend *fe, int onoff) {
+ struct dib7000p_ops *dib7000p_ops = fe->sec_priv;
+ return dib7000p_ops->set_gpio(fe, 8, 0, !onoff);
+}
+
+static int
+dib7070_tuner_sleep(struct dvb_frontend *fe, int onoff) {
+ return 0;
+}
+
+static struct dib0070_config dib7070p_dib0070_config = {
+ .i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
+ .reset = dib7070_tuner_reset,
+ .sleep = dib7070_tuner_sleep,
+ .clock_khz = 12000,
+};
+
+/* DIB7070 generic */
+static struct dibx000_agc_config dib7070_agc_config = {
+ .band_caps = BAND_UHF | BAND_VHF | BAND_LBAND | BAND_SBAND,
+
+ /*
+ * P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5,
+ * P_agc_inv_pwm1=0, P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
+ * P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0
+ */
+ .setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) |
+ (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
+ .inv_gain = 600,
+ .time_stabiliz = 10,
+ .alpha_level = 0,
+ .thlock = 118,
+ .wbd_inv = 0,
+ .wbd_ref = 3530,
+ .wbd_sel = 1,
+ .wbd_alpha = 5,
+ .agc1_max = 65535,
+ .agc1_min = 0,
+ .agc2_max = 65535,
+ .agc2_min = 0,
+ .agc1_pt1 = 0,
+ .agc1_pt2 = 40,
+ .agc1_pt3 = 183,
+ .agc1_slope1 = 206,
+ .agc1_slope2 = 255,
+ .agc2_pt1 = 72,
+ .agc2_pt2 = 152,
+ .agc2_slope1 = 88,
+ .agc2_slope2 = 90,
+ .alpha_mant = 17,
+ .alpha_exp = 27,
+ .beta_mant = 23,
+ .beta_exp = 51,
+ .perform_agc_softsplit = 0,
+};
+
+static struct dibx000_bandwidth_config dib7070_bw_config_12_mhz = {
+ .internal = 60000,
+ .sampling = 15000,
+ .pll_prediv = 1,
+ .pll_ratio = 20,
+ .pll_range = 3,
+ .pll_reset = 1,
+ .pll_bypass = 0,
+ .enable_refdiv = 0,
+ .bypclk_div = 0,
+ .IO_CLK_en_core = 1,
+ .ADClkSrc = 1,
+ .modulo = 2,
+ /* refsel, sel, freq_15k */
+ .sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
+ .ifreq = (0 << 25) | 0,
+ .timf = 20452225,
+ .xtal_hz = 12000000,
+};
+
+static struct dib7000p_config dib7070p_dib7000p_config = {
+ //.output_mode = OUTMODE_MPEG2_FIFO,
+ .output_mode = OUTMODE_MPEG2_SERIAL,
+ //.output_mode = OUTMODE_MPEG2_PAR_GATED_CLK,
+ .output_mpeg2_in_188_bytes = 1,
+
+ .agc_config_count = 1,
+ .agc = &dib7070_agc_config,
+ .bw = &dib7070_bw_config_12_mhz,
+ .tuner_is_baseband = 1,
+ .spur_protect = 1,
+
+ .gpio_dir = 0xfcef, //DIB7000P_GPIO_DEFAULT_DIRECTIONS,
+ .gpio_val = 0x0110, //DIB7000P_GPIO_DEFAULT_VALUES,
+ .gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
+
+ .hostbus_diversity = 1,
+};
+
+static int dib7070_set_param_override(struct dvb_frontend *fe)
+{
+ struct dtv_frontend_properties *p = &fe->dtv_property_cache;
+ //struct dvb_usb_adapter *adap = fe->dvb->priv;
+ //struct dib0700_adapter_state *state = adap->priv;
+ struct dib7000p_ops *dib7000p_ops = fe->sec_priv;
+
+ u16 offset;
+ u8 band = BAND_OF_FREQUENCY(p->frequency/1000);
+ switch (band) {
+ case BAND_VHF: offset = 950; break;
+ default:
+ case BAND_UHF: offset = 550; break;
+ }
+ dib7000p_ops->set_wbd_ref(fe, offset + dib0070_wbd_offset(fe));
+ return dib7000p_ops->set_param_save(fe);
+}
+
static int dvb_register(struct cx23885_tsport *port)
{
struct dib7000p_ops dib7000p_ops;
@@ -993,6 +1107,32 @@ static int dvb_register(struct cx23885_tsport *port)
}
break;
}
+ case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2: {
+ i2c_bus = &dev->i2c_bus[port->nr - 1];
+ //cxusb_ctrl_msg(adap->dev, CMD_DIGITAL, NULL, 0, NULL, 0);
+ //cxusb_bluebird_gpio_pulse(adap->dev, 0x02, 1);
+
+ if (!dvb_attach(dib7000p_attach, &dib7000p_ops))
+ return -ENODEV;
+
+ if (dib7000p_ops.i2c_enumeration(&i2c_bus->i2c_adap, 1, 0x12, &dib7070p_dib7000p_config) < 0) {
+ printk(KERN_WARNING "Unable to enumerate dib7000p\n");
+ return -ENODEV;
+ }
+ fe0->dvb.frontend = dib7000p_ops.init(&i2c_bus->i2c_adap, 0x80, &dib7070p_dib7000p_config);
+ if (fe0->dvb.frontend != NULL) {
+ struct i2c_adapter *tun_i2c;
+ fe0->dvb.frontend->sec_priv = kmalloc(sizeof(dib7000p_ops), GFP_KERNEL);
+ memcpy(fe0->dvb.frontend->sec_priv, &dib7000p_ops, sizeof(dib7000p_ops));
+ tun_i2c = dib7000p_ops.get_i2c_master(fe0->dvb.frontend, DIBX000_I2C_INTERFACE_TUNER, 1);
+ if (!dvb_attach(dib0070_attach, fe0->dvb.frontend, tun_i2c, &dib7070p_dib0070_config)) {
+ return -ENODEV;
+ }
+ ((struct dib7000p_ops *)(fe0->dvb.frontend->sec_priv))->set_param_save = fe0->dvb.frontend->ops.tuner_ops.set_params;
+ fe0->dvb.frontend->ops.tuner_ops.set_params = dib7070_set_param_override;
+ }
+ break;
+ }
case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
diff --git a/drivers/media/pci/cx23885/cx23885.h b/drivers/media/pci/cx23885/cx23885.h
index 0fa4048..8eb7330 100644
--- a/drivers/media/pci/cx23885/cx23885.h
+++ b/drivers/media/pci/cx23885/cx23885.h
@@ -96,6 +96,7 @@
#define CX23885_BOARD_TBS_6981 40
#define CX23885_BOARD_TBS_6980 41
#define CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200 42
+#define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2 43
#define GPIO_0 0x00000001
#define GPIO_1 0x00000002
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
