Hi Laurent,
On 11/03/14 00:15, Laurent Pinchart wrote:
> Add support for the hsync-active, vsync-active and pclk-sample
> properties to the DT bindings and control BT.656 mode implicitly.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/media/i2c/adv7604.txt | 13 +++++++++
> drivers/media/i2c/adv7604.c | 31 ++++++++++++++++++++--
> 2 files changed, 42 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> index 0845c50..2b62c06 100644
> --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> @@ -30,6 +30,19 @@ Optional Properties:
> - adi,disable-cable-reset: Boolean property. When set disables the HDMI
> receiver automatic reset when the HDMI cable is unplugged.
>
> +Optional Endpoint Properties:
> +
> + The following three properties are defined in video-interfaces.txt and are
> + valid for source endpoints only.
> +
> + - hsync-active: Horizontal synchronization polarity. Defaults to active low.
> + - vsync-active: Vertical synchronization polarity. Defaults to active low.
> + - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
> +
> + If none of hsync-active, vsync-active and pclk-sample is specified the
> + endpoint will use embedded BT.656 synchronization.
> +
> +
> Example:
>
> hdmi_receiver@4c {
> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
> index 95cc911..2a92099 100644
> --- a/drivers/media/i2c/adv7604.c
> +++ b/drivers/media/i2c/adv7604.c
> @@ -41,6 +41,7 @@
> #include <media/v4l2-ctrls.h>
> #include <media/v4l2-device.h>
> #include <media/v4l2-dv-timings.h>
> +#include <media/v4l2-of.h>
>
> static int debug;
> module_param(debug, int, 0644);
> @@ -2643,11 +2644,39 @@ MODULE_DEVICE_TABLE(of, adv7604_of_id);
>
> static int adv7604_parse_dt(struct adv7604_state *state)
> {
> + struct v4l2_of_endpoint bus_cfg;
> + struct device_node *endpoint;
> struct device_node *np;
> + unsigned int flags;
> int ret;
>
> np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node;
>
> + /* Parse the endpoint. */
> + endpoint = v4l2_of_get_next_endpoint(np, NULL);
> + if (!endpoint)
> + return -EINVAL;
Perhaps we should document this binding requires at least one endpoint
node ? I guess there is no point in not having any endpoint node ?
> + v4l2_of_parse_endpoint(endpoint, &bus_cfg);
> + of_node_put(endpoint);
> +
> + flags = bus_cfg.bus.parallel.flags;
> +
> + if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
> + state->pdata.inv_hs_pol = 1;
> +
> + if (flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
> + state->pdata.inv_vs_pol = 1;
> +
> + if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
> + state->pdata.inv_llc_pol = 1;
> +
> + if (bus_cfg.bus_type == V4L2_MBUS_BT656) {
> + state->pdata.insert_av_codes = 1;
> + state->pdata.op_656_range = 1;
> + }
> +
> + /* Parse device-specific properties. */
> state->pdata.disable_pwrdnb =
> of_property_read_bool(np, "adi,disable-power-down");
> state->pdata.disable_cable_det_rst =
> @@ -2677,9 +2706,7 @@ static int adv7604_parse_dt(struct adv7604_state *state)
>
> /* HACK: Hardcode the remaining platform data fields. */
> state->pdata.blank_data = 1;
> - state->pdata.op_656_range = 1;
> state->pdata.alt_data_sat = 1;
> - state->pdata.insert_av_codes = 1;
> state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0;
>
> return 0;
--
Regards,
Sylwester
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
