On Thu, Feb 20, 2014 at 07:40:29PM +0000, Sylwester Nawrocki wrote:
> This adds DT binding documentation for Samsung S5C73M3 camera sensor
> with an embedded ISP.
>
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx>
> Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> ---
> Changes since v3:
> - DT binding documentation separated into this patch;
>
> Changes since v2:
> - rephrased 'clocks' and 'clock-names' properties' description;
> ---
> .../devicetree/bindings/media/samsung-s5c73m3.txt | 97 ++++++++++++++++++++
> 1 file changed, 97 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
>
> diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
> new file mode 100644
> index 0000000..4dd3776
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
> @@ -0,0 +1,97 @@
> +Samsung S5C73M3 8Mp camera ISP
> +------------------------------
> +
> +The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video
> +data busses. The I2C bus is the main control bus and additionally the SPI bus
> +is used, mostly for transferring the firmware to and from the device. Two
> +slave device nodes corresponding to these control bus interfaces are required
> +and should be placed under respective bus controller nodes.
So this has both an I2C interface and an SPI interface that are used at
the same time?
> +
> +I2C slave device node
> +---------------------
> +
> +Required properties:
> +
> +- compatible : "samsung,s5c73m3";
> +- reg : I2C slave address of the sensor;
> +- vdd-int-supply : digital power supply (1.2V);
> +- vdda-supply : analog power supply (1.2V);
> +- vdd-reg-supply : regulator input power supply (2.8V);
> +- vddio-host-supply : host I/O power supply (1.8V to 2.8V);
> +- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V);
> +- vdd-af-supply : lens power supply (2.8V);
> +- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin;
> +- standby-gpios : specifier of GPIO connected to the STANDBY pin;
> +- clocks : should contain list of phandle and clock specifier pairs
> + according to common clock bindings for the clocks described
> + in the clock-names property;
> +- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock;
> +
> +Optional properties:
> +
> +- clock-frequency : the frequency at which the "cis_extclk" clock should be
> + configured to operate, in Hz; if this property is not
> + specified default 24 MHz value will be used.
> +
> +The common video interfaces bindings (see video-interfaces.txt) should be used
> +to specify link from the S5C73M3 to an external image data receiver. The S5C73M3
> +device node should contain one 'port' child node with an 'endpoint' subnode for
> +this purpose. The data link from a raw image sensor to the S5C73M3 can be
> +similarly specified, but it is optional since the S5C73M3 ISP and a raw image
> +sensor are usually inseparable and form a hybrid module.
> +
> +Following properties are valid for the endpoint node(s):
> +
> +endpoint subnode
> +----------------
> +
> +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
> + video-interfaces.txt. This sensor doesn't support data lane remapping
> + and physical lane indexes in subsequent elements of the array should
> + be only consecutive ascending values.
> +
> +SPI device node
> +---------------
> +
> +Required properties:
> +
> +- compatible : "samsung,s5c73m3";
It might make sense to explicitly link these two nodes somehow, in case
multiple instances appear somewhere. However, that can come later in the
case of a multi-instance device, and isn't necessary now.
> +
> +For more details see description of the SPI busses bindings
> +(../spi/spi-bus.txt) and bindings of a specific bus controller.
> +
> +Example:
> +
> +i2c@138A000000 {
> + ...
> + s5c73m3@3c {
> + compatible = "samsung,s5c73m3";
> + reg = <0x3c>;
> + vdd-int-supply = <&buck9_reg>;
> + vdda-supply = <&ldo17_reg>;
> + vdd-reg-supply = <&cam_io_reg>;
> + vddio-host-supply = <&ldo18_reg>;
> + vddio-cis-supply = <&ldo9_reg>;
> + vdd-af-supply = <&cam_af_reg>;
> + clock-frequency = <24000000>;
> + clocks = <&clk 0>;
> + clock-names = "cis_extclk";
> + reset-gpios = <&gpf1 3 1>;
> + standby-gpios = <&gpm0 1 1>;
> + port {
> + s5c73m3_ep: endpoint {
> + remote-endpoint = <&csis0_ep>;
> + data-lanes = <1 2 3 4>;
> + };
> + };
> + };
> +};
> +
> +spi@1392000 {
> + ...
> + s5c73m3_spi: s5c73m3 {
Nit: this should have a 0 unit-address to match the reg.
> + compatible = "samsung,s5c73m3";
> + reg = <0>;
> + ...
> + };
> +};
Otherwise I don't see anything problematic about the binding.
Acked-by: Mark Rutland <mark.rutland@xxxxxxx>
Cheers,
Mark.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
