Add ImgTec IR decoder driver to the build system. Signed-off-by: James Hogan <james.hogan@xxxxxxxxxx> Cc: Mauro Carvalho Chehab <m.chehab@xxxxxxxxxxx> Cc: linux-media@xxxxxxxxxxxxxxx --- drivers/media/rc/Kconfig | 2 ++ drivers/media/rc/Makefile | 1 + drivers/media/rc/img-ir/Kconfig | 26 ++++++++++++++++++++++++++ drivers/media/rc/img-ir/Makefile | 6 ++++++ 4 files changed, 35 insertions(+) create mode 100644 drivers/media/rc/img-ir/Kconfig create mode 100644 drivers/media/rc/img-ir/Makefile diff --git a/drivers/media/rc/Kconfig b/drivers/media/rc/Kconfig index 3b25887..8fbd377 100644 --- a/drivers/media/rc/Kconfig +++ b/drivers/media/rc/Kconfig @@ -309,6 +309,8 @@ config IR_RX51 The driver uses omap DM timers for generating the carrier wave and pulses. +source "drivers/media/rc/img-ir/Kconfig" + config RC_LOOPBACK tristate "Remote Control Loopback Driver" depends on RC_CORE diff --git a/drivers/media/rc/Makefile b/drivers/media/rc/Makefile index 36dafed..f8b54ff 100644 --- a/drivers/media/rc/Makefile +++ b/drivers/media/rc/Makefile @@ -32,3 +32,4 @@ obj-$(CONFIG_IR_GPIO_CIR) += gpio-ir-recv.o obj-$(CONFIG_IR_IGUANA) += iguanair.o obj-$(CONFIG_IR_TTUSBIR) += ttusbir.o obj-$(CONFIG_RC_ST) += st_rc.o +obj-$(CONFIG_IR_IMG) += img-ir/ diff --git a/drivers/media/rc/img-ir/Kconfig b/drivers/media/rc/img-ir/Kconfig new file mode 100644 index 0000000..60eaba6 --- /dev/null +++ b/drivers/media/rc/img-ir/Kconfig @@ -0,0 +1,26 @@ +config IR_IMG + tristate "ImgTec IR Decoder" + depends on RC_CORE + select IR_IMG_HW if !IR_IMG_RAW + help + Say Y or M here if you want to use the ImgTec infrared decoder + functionality found in SoCs such as TZ1090. + +config IR_IMG_RAW + bool "Raw decoder" + depends on IR_IMG + help + Say Y here to enable the raw mode driver which passes raw IR signal + changes to the IR raw decoders for software decoding. This is much + less reliable (due to lack of timestamps) and consumes more + processing power than using hardware decode, but can be useful for + testing, debug, and to make more protocols available. + +config IR_IMG_HW + bool "Hardware decoder" + depends on IR_IMG + help + Say Y here to enable the hardware decode driver which decodes the IR + signals in hardware. This is more reliable, consumes less processing + power since only a single interrupt is received for each scancode, + and allows an IR scancode to be used as a wake event. diff --git a/drivers/media/rc/img-ir/Makefile b/drivers/media/rc/img-ir/Makefile new file mode 100644 index 0000000..4ef86ed --- /dev/null +++ b/drivers/media/rc/img-ir/Makefile @@ -0,0 +1,6 @@ +img-ir-y := img-ir-core.o +img-ir-$(CONFIG_IR_IMG_RAW) += img-ir-raw.o +img-ir-$(CONFIG_IR_IMG_HW) += img-ir-hw.o +img-ir-objs := $(img-ir-y) + +obj-$(CONFIG_IR_IMG) += img-ir.o -- 1.8.3.2 -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
