From: Mauro Carvalho Chehab <m.chehab@xxxxxxxxxxx>
The I2C output messages is too polluted. Clean it a little
bit, by:
- use the proper core support for memory dumps;
- hide most stuff under the i2c_debug umbrella;
- add the missing KERN_CONT where needed;
- use 2 levels or verbosity. Only the second one
will show the I2C transfer data.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@xxxxxxxxxxx>
---
drivers/media/usb/em28xx/em28xx-i2c.c | 91 ++++++++++++++++++-----------------
1 file changed, 47 insertions(+), 44 deletions(-)
diff --git a/drivers/media/usb/em28xx/em28xx-i2c.c b/drivers/media/usb/em28xx/em28xx-i2c.c
index 16862c4cc745..ff288023e330 100644
--- a/drivers/media/usb/em28xx/em28xx-i2c.c
+++ b/drivers/media/usb/em28xx/em28xx-i2c.c
@@ -41,7 +41,7 @@ MODULE_PARM_DESC(i2c_scan, "scan i2c bus at insmod time");
static unsigned int i2c_debug;
module_param(i2c_debug, int, 0644);
-MODULE_PARM_DESC(i2c_debug, "enable debug messages [i2c]");
+MODULE_PARM_DESC(i2c_debug, "i2c debug message level (1: normal debug, 2: show I2C transfers)");
/*
* em2800_i2c_send_bytes()
@@ -80,7 +80,9 @@ static int em2800_i2c_send_bytes(struct em28xx *dev, u8 addr, u8 *buf, u16 len)
if (ret == 0x80 + len - 1)
return len;
if (ret == 0x94 + len - 1) {
- em28xx_warn("R05 returned 0x%02x: I2C timeout", ret);
+ if (i2c_debug)
+ em28xx_warn("R05 returned 0x%02x: I2C timeout",
+ ret);
return -EIO;
}
if (ret < 0) {
@@ -90,7 +92,8 @@ static int em2800_i2c_send_bytes(struct em28xx *dev, u8 addr, u8 *buf, u16 len)
}
msleep(5);
}
- em28xx_warn("write to i2c device at 0x%x timed out\n", addr);
+ if (i2c_debug)
+ em28xx_warn("write to i2c device at 0x%x timed out\n", addr);
return -EIO;
}
@@ -124,7 +127,9 @@ static int em2800_i2c_recv_bytes(struct em28xx *dev, u8 addr, u8 *buf, u16 len)
if (ret == 0x84 + len - 1)
break;
if (ret == 0x94 + len - 1) {
- em28xx_warn("R05 returned 0x%02x: I2C timeout", ret);
+ if (i2c_debug)
+ em28xx_warn("R05 returned 0x%02x: I2C timeout",
+ ret);
return -EIO;
}
if (ret < 0) {
@@ -134,8 +139,11 @@ static int em2800_i2c_recv_bytes(struct em28xx *dev, u8 addr, u8 *buf, u16 len)
}
msleep(5);
}
- if (ret != 0x84 + len - 1)
- em28xx_warn("read from i2c device at 0x%x timed out\n", addr);
+ if (ret != 0x84 + len - 1) {
+ if (i2c_debug)
+ em28xx_warn("read from i2c device at 0x%x timed out\n",
+ addr);
+ }
/* get the received message */
ret = dev->em28xx_read_reg_req_len(dev, 0x00, 4-len, buf2, len);
@@ -212,8 +220,9 @@ retry:
}
if (ret == 0x10) {
- em28xx_warn("I2C transfer timeout on writing to addr 0x%02x",
- addr);
+ if (i2c_debug)
+ em28xx_warn("I2C transfer timeout on writing to addr 0x%02x",
+ addr);
return -EIO;
}
em28xx_warn("write to i2c device at 0x%x timed out (ret=0x%02x)\n",
@@ -269,7 +278,9 @@ static int em28xx_i2c_recv_bytes(struct em28xx *dev, u16 addr, u8 *buf, u16 len)
} while (time_is_after_jiffies(timeout));
if (ret == 0x10) {
- em28xx_warn("I2C transfer timeout on read from addr 0x%02x", addr);
+ if (i2c_debug)
+ em28xx_warn("I2C transfer timeout on read from addr 0x%02x",
+ addr);
return -EIO;
}
@@ -381,7 +392,8 @@ static int em25xx_bus_B_recv_bytes(struct em28xx *dev, u16 addr, u8 *buf,
if (!ret)
return len;
else if (ret > 0) {
- em28xx_warn("Bus B R08 returned 0x%02x: I2C timeout", ret);
+ if (i2c_debug)
+ em28xx_warn("Bus B R08 returned 0x%02x: I2C timeout", ret);
return -EIO;
}
@@ -424,10 +436,6 @@ static inline int i2c_check_for_device(struct em28xx_i2c_bus *i2c_bus, u16 addr)
rc = em2800_i2c_check_for_device(dev, addr);
else if (i2c_bus->algo_type == EM28XX_I2C_ALGO_EM25XX_BUS_B)
rc = em25xx_bus_B_check_for_device(dev, addr);
- if (rc < 0) {
- if (i2c_debug)
- printk(" no device\n");
- }
return rc;
}
@@ -436,7 +444,7 @@ static inline int i2c_recv_bytes(struct em28xx_i2c_bus *i2c_bus,
{
struct em28xx *dev = i2c_bus->dev;
u16 addr = msg.addr << 1;
- int byte, rc = -EOPNOTSUPP;
+ int rc = -EOPNOTSUPP;
if (i2c_bus->algo_type == EM28XX_I2C_ALGO_EM28XX)
rc = em28xx_i2c_recv_bytes(dev, addr, msg.buf, msg.len);
@@ -444,10 +452,6 @@ static inline int i2c_recv_bytes(struct em28xx_i2c_bus *i2c_bus,
rc = em2800_i2c_recv_bytes(dev, addr, msg.buf, msg.len);
else if (i2c_bus->algo_type == EM28XX_I2C_ALGO_EM25XX_BUS_B)
rc = em25xx_bus_B_recv_bytes(dev, addr, msg.buf, msg.len);
- if (i2c_debug) {
- for (byte = 0; byte < msg.len; byte++)
- printk(" %02x", msg.buf[byte]);
- }
return rc;
}
@@ -456,12 +460,8 @@ static inline int i2c_send_bytes(struct em28xx_i2c_bus *i2c_bus,
{
struct em28xx *dev = i2c_bus->dev;
u16 addr = msg.addr << 1;
- int byte, rc = -EOPNOTSUPP;
+ int rc = -EOPNOTSUPP;
- if (i2c_debug) {
- for (byte = 0; byte < msg.len; byte++)
- printk(" %02x", msg.buf[byte]);
- }
if (i2c_bus->algo_type == EM28XX_I2C_ALGO_EM28XX)
rc = em28xx_i2c_send_bytes(dev, addr, msg.buf, msg.len, stop);
else if (i2c_bus->algo_type == EM28XX_I2C_ALGO_EM2800)
@@ -506,7 +506,7 @@ static int em28xx_i2c_xfer(struct i2c_adapter *i2c_adap,
}
for (i = 0; i < num; i++) {
addr = msgs[i].addr << 1;
- if (i2c_debug)
+ if (i2c_debug > 1)
printk(KERN_DEBUG "%s at %s: %s %s addr=%02x len=%d:",
dev->name, __func__ ,
(msgs[i].flags & I2C_M_RD) ? "read" : "write",
@@ -515,24 +515,33 @@ static int em28xx_i2c_xfer(struct i2c_adapter *i2c_adap,
if (!msgs[i].len) { /* no len: check only for device presence */
rc = i2c_check_for_device(i2c_bus, addr);
if (rc < 0) {
+ if (i2c_debug > 1)
+ printk(KERN_CONT " no device\n");
rt_mutex_unlock(&dev->i2c_bus_lock);
return rc;
}
} else if (msgs[i].flags & I2C_M_RD) {
/* read bytes */
rc = i2c_recv_bytes(i2c_bus, msgs[i]);
+
+ if (i2c_debug > 1 && rc >= 0)
+ printk(KERN_CONT " %*ph",
+ msgs[i].len, msgs[i].buf);
} else {
+ if (i2c_debug > 1)
+ printk(KERN_CONT " %*ph",
+ msgs[i].len, msgs[i].buf);
+
/* write bytes */
rc = i2c_send_bytes(i2c_bus, msgs[i], i == num - 1);
}
if (rc < 0) {
- if (i2c_debug)
- printk(" ERROR: %i\n", rc);
+ if (i2c_debug > 1)
+ printk(KERN_CONT " ERROR: %i\n", rc);
rt_mutex_unlock(&dev->i2c_bus_lock);
return rc;
- }
- if (i2c_debug)
- printk("\n");
+ } else if (i2c_debug > 1)
+ printk(KERN_CONT "\n");
}
rt_mutex_unlock(&dev->i2c_bus_lock);
@@ -615,7 +624,7 @@ static int em28xx_i2c_eeprom(struct em28xx *dev, unsigned bus,
* calculation and returned device dataset. Simplifies the code a lot,
* but we might have to deal with multiple sizes in the future !
*/
- int i, err;
+ int err;
struct em28xx_eeprom *dev_config;
u8 buf, *data;
@@ -646,20 +655,14 @@ static int em28xx_i2c_eeprom(struct em28xx *dev, unsigned bus,
goto error;
}
- /* Display eeprom content */
- for (i = 0; i < len; i++) {
- if (0 == (i % 16)) {
- if (dev->eeprom_addrwidth_16bit)
- em28xx_info("i2c eeprom %04x:", i);
- else
- em28xx_info("i2c eeprom %02x:", i);
- }
- printk(" %02x", data[i]);
- if (15 == (i % 16))
- printk("\n");
+ if (i2c_debug) {
+ /* Display eeprom content */
+ print_hex_dump(KERN_INFO, "eeprom ", DUMP_PREFIX_OFFSET,
+ 16, 1, data, len, true);
+
+ if (dev->eeprom_addrwidth_16bit)
+ em28xx_info("eeprom %06x: ... (skipped)\n", 256);
}
- if (dev->eeprom_addrwidth_16bit)
- em28xx_info("i2c eeprom %04x: ... (skipped)\n", i);
if (dev->eeprom_addrwidth_16bit &&
data[0] == 0x26 && data[3] == 0x00) {
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
