Re: [PATCH] media: i2c: adv7343: fix the DT binding properties

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Stephen,

This patch should have been marked as RFC.

Thanks for the review.

On Sat, Sep 14, 2013 at 4:16 AM, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote:
> On 09/13/2013 05:57 AM, Prabhakar Lad wrote:
>> From: "Lad, Prabhakar" <prabhakar.csengg@xxxxxxxxx>
>>
>> This patch fixes the DT binding properties of adv7343 decoder.
>> The pdata which was being read from the DT property, is removed
>> as this can done internally in the driver using cable detection
>> register.
>>
>> This patch also removes the pdata of ADV7343 which was passed from
>> DA850 machine.
>
>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
>
>>  Required Properties :
>>  - compatible: Must be "adi,adv7343"
>> +- reg: I2C device address.
>> +- vddio-supply: I/O voltage supply.
>> +- vddcore-supply: core voltage supply.
>> +- vaa-supply: Analog power supply.
>> +- pvdd-supply: PLL power supply.
>
> Old DTs won't contain those properties. This breaks the DT ABI if those
> properties are required. Is that acceptable?
>
As of now adv7343 via DT binding is not enabled in any platforms
so this wont break any DT ABI.

> If it is, I think we should document that older versions of the binding
> didn't require those properties, so they may in fact be missing.
>
> I note that this patch doesn't actually update the driver to
> regulator_get() anything. Shouldn't it?
>
As of now the driver isn’t enabling/accepting the regulators,
so should I add those in DT properties or not ?

>>  Optional Properties :
>> -- adi,power-mode-sleep-mode: on enable the current consumption is reduced to
>> -                           micro ampere level. All DACs and the internal PLL
>> -                           circuit are disabled.
>> -- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
>> -                        internal PLL 1 circuit to be powered down and the
>> -                        oversampling to be switched off.
>> -- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
>> -                           0 = OFF and 1 = ON, Default value when this
>> -                           property is not specified is <0 0 0 0 0 0>.
>> -- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF
>> -                              and 1 = ON, Default value when this property is
>> -                              not specified is <0 0>.
>
> At a very quick glance, it's not really clear why those properties are
> being removed. They seem like HW configuration, so might be fine to put
> into DT. What replaces these?

Yes these were HW configuration but, its now internally handled in
the driver.  The 'ad,adv7343-power-mode-dac' property which enabled the
DAC's 1..6 , so now in the driver by default all the DAC's are enabled by
default and enable unconnected DAC auto power down. Similarly
'ad,adv7343-sd-config-dac-out' property enabled SD DAC's 1..2 but
now is enabled by reading the CABLE DETECT register which tells
the status of DAC1/2.

Regards,
--Prabhakar
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux