Hi Mark, On Tue, Aug 27, 2013 at 8:54 PM, Mark Rutland <mark.rutland@xxxxxxx> wrote: > [fixing up devicetree list address] > Thanks! > On Mon, Aug 26, 2013 at 03:41:45AM +0100, Prabhakar Lad wrote: >> Hi Sylwester, >> >> On Fri, Aug 23, 2013 at 11:33 PM, Sylwester Nawrocki >> <s.nawrocki@xxxxxxxxxxx> wrote: >> > Cc: DT binding maintainers > > Cheers! > >> > >> > On 07/20/2013 08:21 AM, Lad, Prabhakar wrote: >> >> From: "Lad, Prabhakar" <prabhakar.csengg@xxxxxxxxx> >> >> >> >> add OF support for the adv7343 driver. >> >> >> >> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx> >> >> --- >> > [...] >> >> .../devicetree/bindings/media/i2c/adv7343.txt | 48 ++++++++++++++++++++ >> >> drivers/media/i2c/adv7343.c | 46 ++++++++++++++++++- >> >> 2 files changed, 93 insertions(+), 1 deletion(-) >> >> create mode 100644 Documentation/devicetree/bindings/media/i2c/adv7343.txt >> >> >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt >> >> new file mode 100644 >> >> index 0000000..5653bc2 >> >> --- /dev/null >> >> +++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt >> >> @@ -0,0 +1,48 @@ >> >> +* Analog Devices adv7343 video encoder >> >> + >> >> +The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP >> >> +package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite >> >> +(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard >> >> +definition (SD), enhanced definition (ED), or high definition (HD) video >> >> +formats. >> >> + >> >> +Required Properties : >> >> +- compatible: Must be "adi,adv7343" >> >> + >> >> +Optional Properties : >> >> +- adi,power-mode-sleep-mode: on enable the current consumption is reduced to >> >> + micro ampere level. All DACs and the internal PLL >> >> + circuit are disabled. > > This seems to be a boolean property, and I couldn't find any description > in the linked datasheet of the constraints under which the unit may be > put into sleep mode. > > Why do we require this property in the dt? Can the driver not always put > a adv734x into sleep mode if it wants to, and then wake it up as > required? > The adv7343 decoder, fits on da850/dm6467 etc.. For the da850 it supports only SD where as the dm6467 supports HD/SD/ED for which DAC 1-6 of Register 0x0 varies for this board so I added them as the platform data but I got a review comment in the ML asking to add entire register as the pdata instead of DAC 1-6, so because of which it is being converted in the same way for DT. >> > >> > Sorry for getting back so late to this. I realize this is already queued in >> > the media tree. But this binding doesn't look good enough to me. I think it >> > will need to be corrected during upcoming -rc period. >> > >> Thanks for the catch :-) >> >> > It might be hard to figure out only from the chip's datasheet what >> > adi,power-mode-sleep-mode really refers to. AFAICS it is for assigning some >> > value to a specific register. If we really need to specify register values >> > in the device tree then it would probably make sense to describe to which >> > register this apply. Now the name looks like derived from some structure >> > member name in the Linux driver of the device. >> > >> the property is derived from the datasheet itself for example the >> 'adi,power-mode-sleep-mode' --> Register 0x0 power mode bit 0 >> 'adi,power-mode-pll-ctrl' ---> Register 0x0 power mode bit 1 >> 'adi,dac-enable' ----> Register 0x0 power mode bit 2-7 >> 'adi,sd-dac-enable' ---> Register 0x82 SD mode register bit 1-2 >> >> [1] http://www.analog.com/static/imported-files/data_sheets/ADV7342_7343.pdf >> >> >> +- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows >> >> + internal PLL 1 circuit to be powered down and the >> >> + oversampling to be switched off. > > This affects whether or not oversampling is possible. That sounds like > it should be a run-time configurable rather than a fixed property of the > device. > ditto >> > >> > Similar comments applies to this property. >> > >> >> +- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6, >> >> + 0 = OFF and 1 = ON, Default value when this >> >> + property is not specified is <0 0 0 0 0 0>. >> > >> > Name of the property is incorrect here. It has changed to "adi,dac-enable". >> > >> OK > > Why do we need this property at all? Might some DACs not be wired up to > anything? > > Surely this could be configured at run-time as and when the user wants > to use the DACs. > >> >> >> +- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF >> >> + and 1 = ON, Default value when this property is >> >> + not specified is <0 0>. >> > >> > Similarly, "adi,sd-dac-enable. >> > >> OK > > Again, couldn't this be done at run-time? > > Do we need to permanently disable/enable some DACs? If so, why? > ditto. > I also note from the spec that the unit has two clocks, CLKIN_A and > CLKIN_B that aren't in the binding, but should be. Some regulators > too (VDD, PVDD, VAA, VDD_IO, VREF?). > OK Regards, --Prabhakar Lad -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
