On 02/03/2013 02:04 PM, Jose Alberto Reguero wrote:
On Sábado, 2 de febrero de 2013 23:00:45 Michael Krufky escribió:
On Fri, Jan 11, 2013 at 6:45 PM, Jose Alberto Reguero
<jareguero@xxxxxxxxxxxxxx> wrote:
On Viernes, 11 de enero de 2013 20:38:01 Antti Palosaari escribió:
Hello Jose and Gianluca
Could you test that (tda18218 & mxl5007t):
http://git.linuxtv.org/anttip/media_tree.git/shortlog/refs/heads/it9135_t
une r
I wonder if ADC config logic still works for superheterodyne tuners
(tuner having IF). I changed it to adc / 2 always due to IT9135 tuner.
That makes me wonder it possible breaks tuners having IF, as ADC was
clocked just over 20MHz and if it is half then it is 10MHz. For BB that
is enough, but I think that having IF, which is 4MHz at least for 8MHz
BW it is too less.
F*ck I hate to maintain driver without a hardware! Any idea where I can
get AF9035 device having tda18218 or mxl5007t?
regards
Antti
Still pending the changes for mxl5007t. Attached is a patch for that.
Changes to make work Avermedia Twinstar with the af9035 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@xxxxxxxxxxxxxx>
Jose Alberto
diff -upr linux/drivers/media/tuners/mxl5007t.c
linux.new/drivers/media/tuners/mxl5007t.c
--- linux/drivers/media/tuners/mxl5007t.c 2012-08-14
05:45:22.000000000 +0200 +++ linux.new/drivers/media/tuners/mxl5007t.c
2013-01-10 19:23:09.247556275 +0100
@@ -374,7 +374,6 @@ static struct reg_pair_t *mxl5007t_calc_
mxl5007t_set_if_freq_bits(state, cfg->if_freq_hz, cfg->invert_if);
mxl5007t_set_xtal_freq_bits(state, cfg->xtal_freq_hz);
- set_reg_bits(state->tab_init, 0x04, 0x01, cfg->loop_thru_enable);
set_reg_bits(state->tab_init, 0x03, 0x08, cfg->clk_out_enable <<
3);
set_reg_bits(state->tab_init, 0x03, 0x07, cfg->clk_out_amp);
This is a configurable option - it should not be removed, just
configure your glue code to not use that option if you dont want
it.... unless there's some other reason why you're removing this?
I just move the code to a mxl5007t_attach because with dual tuner until the
code is executed, the other tuner don't work. It can be left here also.
@@ -531,9 +530,12 @@ static int mxl5007t_tuner_init(struct mx
struct reg_pair_t *init_regs;
int ret;
- ret = mxl5007t_soft_reset(state);
- if (mxl_fail(ret))
+ if (!state->config->no_reset) {
+ ret = mxl5007t_soft_reset(state);
+ if (mxl_fail(ret))
goto fail;
+ }
+
this seems wrong to me. why would you want to prevent the driver from
doing a soft reset?
That is because with my hardware and dual tuner, when one tuner do reset, the
other one is perturbed, and the stream has errors.
/* calculate initialization reg array */
init_regs = mxl5007t_calc_init_regs(state, mode);
@@ -887,7 +889,12 @@ struct dvb_frontend *mxl5007t_attach(str
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
- ret = mxl5007t_get_chip_id(state);
+ if (!state->config->no_probe)
+ ret = mxl5007t_get_chip_id(state);
+
+ ret = mxl5007t_write_reg(state, 0x04,
+ state->config->loop_thru_enable);
+
Can you explain why this change was made? ^^
mxl5007t_get_chip_id has a read, and with the hardware I have, after the read
operation is made, communication with the chip don't work.
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 0);
diff -upr linux/drivers/media/tuners/mxl5007t.h
linux.new/drivers/media/tuners/mxl5007t.h
--- linux/drivers/media/tuners/mxl5007t.h 2012-08-14
05:45:22.000000000 +0200 +++ linux.new/drivers/media/tuners/mxl5007t.h
2013-01-10 19:19:11.204379581 +0100
@@ -73,8 +73,10 @@ struct mxl5007t_config {
enum mxl5007t_xtal_freq xtal_freq_hz;
enum mxl5007t_if_freq if_freq_hz;
unsigned int invert_if:1;
- unsigned int loop_thru_enable:1;
+ unsigned int loop_thru_enable:3;
Why widen this boolean to three bits?
I just use the value 3 for this option(taken from windows driver) and it works
well.
Thanks for review the code.
Jose Alberto
unsigned int clk_out_enable:1;
+ unsigned int no_probe:1;
+ unsigned int no_reset:1;
};
#if defined(CONFIG_MEDIA_TUNER_MXL5007T) ||
(defined(CONFIG_MEDIA_TUNER_MXL5007T_MODULE) && defined(MODULE))
diff -upr linux/drivers/media/usb/dvb-usb-v2/af9035.c
linux.new/drivers/media/usb/dvb-usb-v2/af9035.c
--- linux/drivers/media/usb/dvb-usb-v2/af9035.c 2013-01-07
05:45:57.000000000 +0100
+++ linux.new/drivers/media/usb/dvb-usb-v2/af9035.c 2013-01-12
00:30:57.557310465 +0100
@@ -886,13 +886,17 @@ static struct mxl5007t_config af9035_mxl
.loop_thru_enable = 0,
.clk_out_enable = 0,
.clk_out_amp = MxL_CLKOUT_AMP_0_94V,
+ .no_probe = 1,
+ .no_reset = 1,
}, {
.xtal_freq_hz = MxL_XTAL_24_MHZ,
.if_freq_hz = MxL_IF_4_57_MHZ,
.invert_if = 0,
- .loop_thru_enable = 1,
+ .loop_thru_enable = 3,
.clk_out_enable = 1,
.clk_out_amp = MxL_CLKOUT_AMP_0_94V,
+ .no_probe = 1,
+ .no_reset = 1,
}
};
This patch cannot be merged as-is. I'm sorry. If you could explain
why each change was made, then perhaps I would be able to advise
better how to make this work on your device without breaking others.
-Mike Krufky
Mike, Jose,
I think there is multiple bugs - both existing and new ones added by Jose.
First existing MxL5007t driver bugs, which are tried to resolve by Jose
just wrongly.
You configure clock output and RF loop-through only after first tune and
during every tune.
Control flow of mxl5007t init seems to be totally broken logically and
cannot work if there is slave tuner used.
Relevant control flow bug is that:
mxl5007t_set_params() {
mxl5007t_tuner_init() {
mxl5007t_soft_reset()
-- configure clock output
-- configure RF loop-through
}
}
RF loop-through as well clock output should be configured on attach()
that you could trust slave tuner is operational just after all is
attached().
Also, there is another bug, which likely causes disturbance to picture
Jose mentioned. MxL5007t soft reset resets all registers to default
state. You do that *every* time when set_params() is called. Could you
guess what happens to clock output and RF loop-through slave tuner is using?
I made month or two back patch series fixing similar problems of FC0012
driver. See example from there. Jose's hacks are not mostly relevant
after that MxL5007t driver is fixed to offer clock and loop-through
correctly to the slave tuner.
************************
Another issue is that register 04, which contains loop-though and some
other bits. Jose changes its value from 1 to 3. Is that change really
needed? What happens if you leave it just 1? You should not change
options like that just for fun without need.
regards
Antti
--
http://palosaari.fi/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
