Hi, Since a few weeks, I am unable to use my TerraTec Cinergy T PCIe dual card anymore. On the kernel and drivers side, everything seems to be working as expected but I get no signal from any channel. It used to work and I have done too many updates recently to be able to pinpoint to from which point it stopped to work. Plugging the same cable to my TV tuner I get perfect reception so no change in signal quality. I am running Arch Linux with linux 3.7.1 on an x86_64 architecture. Following are some logs. Kernel logs when loading cx23885 module: ### [93752.708088] cx23885 driver version 0.0.3 loaded [93752.708954] CORE cx23885[0]: subsystem: 153b:117e, board: TerraTec Cinergy T PCIe Dual [card=34,autodetected] [93752.847421] cx25840 12-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0]) [93753.502291] cx25840 12-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes) [93753.518236] cx23885_dvb_register() allocating 1 frontend(s) [93753.518242] cx23885[0]: cx23885 based dvb card [93753.533378] drxk: status = 0x639160d9 [93753.533383] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz [93753.606391] DRXK driver version 0.9.4300 [93753.630635] drxk: frontend initialized. [93753.667152] mt2063_attach: Attaching MT2063 [93753.667156] DVB: registering new adapter (cx23885[0]) [93753.667161] cx23885 0000:03:00.0: DVB: registering adapter 0 frontend 0 (DRXK DVB-T)... [93753.670728] cx23885_dvb_register() allocating 1 frontend(s) [93753.670732] cx23885[0]: cx23885 based dvb card [93753.686602] drxk: status = 0x639130d9 [93753.686605] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz [93753.759577] DRXK driver version 0.9.4300 [93753.783845] drxk: frontend initialized. [93753.783852] mt2063_attach: Attaching MT2063 [93753.783854] DVB: registering new adapter (cx23885[0]) [93753.783858] cx23885 0000:03:00.0: DVB: registering adapter 1 frontend 0 (DRXK DVB-C DVB-T)... [93753.784284] cx23885_dev_checkrevision() Hardware revision = 0xa5 [93753.784290] cx23885[0]/0: found at 0000:03:00.0, rev: 4, irq: 18, latency: 0, mmio: 0xfb800000 ### Kernel logs when scanning ### [93853.705675] mt2063: detected a mt2063 B3 ### "femon -H -a0" output: ### FE: DRXK DVB-T (DVBT) Problem retrieving frontend information: Resource temporarily unavailable status SCV | signal 49% | snr 0% | ber 2014507767 | unc 1 | ### Meaningful bits of an strace of the same command ### ioctl(3, FE_READ_STATUS, 0x7fff69172ef0) = 0 ioctl(3, FE_READ_BER, 0x7fff69173018) = -1 EAGAIN (Resource temporarily unavailable) ioctl(3, FE_READ_SIGNAL_STRENGTH, 0x7fff6917301c) = -1 EAGAIN (Resource temporarily unavailable) ioctl(3, FE_READ_SNR, 0x7fff6917301e) = -1 EAGAIN (Resource temporarily unavailable) ioctl(3, FE_READ_UNCORRECTED_BLOCKS, 0x7fff69173020) = -1 EAGAIN (Resource temporarily unavailable) ### w_scan give "no signal" result. dvbscan give "Unable to query frontend status" Any hint to where I should look would be welcome! Regards, -- Cédric Girard -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
