Re: [PATCH RFC v1 2/2] V4L: Add driver for OV9650/52 image sensors

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sylwester,

A quick review below:

On Sat January 5 2013 00:10:23 Sylwester Nawrocki wrote:
> This patch adds V4L2 sub-device driver for OV9650/OV9652
> image sensors.
> 
> The driver exposes following V4L2 controls:
> - auto/manual exposure, auto exposure reference area,
> - auto/manual white balance,
> - auto/manual gain, auto gain ceiling,
> - brightness, saturation, sharpness,
> - horizontal/vertical flip,
> - color bar test pattern,
> - banding filter (power line frequency),
> - g/s_frame_interval pad level op.
> 
> TODO:
>  - add support for more resolutions (QQVGA, CIF, QCIF, ...),
> 
> This driver has been tested only with 12 and 24 MHz external
> clock frequency.
> 
> Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@xxxxxxxxx>
> ---
>  drivers/media/i2c/Kconfig  |    7 +
>  drivers/media/i2c/Makefile |    1 +
>  drivers/media/i2c/ov9650.c | 1684 ++++++++++++++++++++++++++++++++++++++++++++
>  include/media/ov9650.h     |   20 +
>  4 files changed, 1712 insertions(+), 0 deletions(-)
>  create mode 100644 drivers/media/i2c/ov9650.c
>  create mode 100644 include/media/ov9650.h
> 
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 24d78e2..182852f 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -421,6 +421,13 @@ config VIDEO_OV7670
>  	  OV7670 VGA camera.  It currently only works with the M88ALP01
>  	  controller.
>  
> +config VIDEO_OV9650
> +	tristate "OmniVision OV9650/OV9652 sensor support"
> +	depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
> +	---help---
> +	  This is a V4L2 sensor-level driver for the Omnivision
> +	  OV9650 and OV9652 camera sensors.
> +
>  config VIDEO_VS6624
>  	tristate "ST VS6624 sensor support"
>  	depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index b1d62df..8b62e54 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -47,6 +47,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
>  obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
>  obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
>  obj-$(CONFIG_VIDEO_OV7670) 	+= ov7670.o
> +obj-$(CONFIG_VIDEO_OV9650) += ov9650.o
>  obj-$(CONFIG_VIDEO_TCM825X) += tcm825x.o
>  obj-$(CONFIG_VIDEO_TVEEPROM) += tveeprom.o
>  obj-$(CONFIG_VIDEO_MT9M032) += mt9m032.o
> diff --git a/drivers/media/i2c/ov9650.c b/drivers/media/i2c/ov9650.c
> new file mode 100644
> index 0000000..9ff960d
> --- /dev/null
> +++ b/drivers/media/i2c/ov9650.c
> @@ -0,0 +1,1684 @@
> +/*
> + * Omnivision OV9650/OV9652 CMOS Image Sensor driver
> + *
> + * Copyright (C) 2012, Sylwester Nawrocki <sylvester.nawrocki@xxxxxxxxx>
> + *
> + * Register definitions and initial settings based on a driver written
> + * by Vladimir Fonov.
> + * Copyright (c) 2010, Vladimir Fonov
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +#define pr_fmt(fmt) "%s:%d " fmt, __func__, __LINE__
> +
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/kernel.h>
> +#include <linux/media.h>
> +#include <linux/module.h>
> +#include <linux/ratelimit.h>
> +#include <linux/slab.h>
> +#include <linux/string.h>
> +
> +#include <media/image-sizes.h>
> +#include <media/media-entity.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-subdev.h>
> +#include <media/v4l2-mediabus.h>
> +#include <media/ov9650.h>
> +
> +static int debug = 2;
> +module_param(debug, int, 0644);
> +MODULE_PARM_DESC(debug, "Debug level (0-2)");
> +
> +#define DRIVER_NAME "OV9650"
> +
> +/*
> + * OV9650/OV9652 register definitions
> + */
> +#define REG_GAIN		0x00	/* Gain control, AGC[7:0] */
> +#define REG_BLUE		0x01	/* AWB - Blue chanel gain */
> +#define REG_RED			0x02	/* AWB - Red chanel gain */
> +#define REG_VREF		0x03	/* [7:6] - AGC[9:8], [5:3]/[2:0] */
> +#define  VREF_GAIN_MASK		0xc0	/* - VREF end/start low 3 bits */
> +#define REG_COM1		0x04
> +#define  COM1_CCIR656		0x40
> +#define REG_B_AVE		0x05
> +#define REG_GB_AVE		0x06
> +#define REG_GR_AVE		0x07
> +#define REG_R_AVE		0x08
> +#define REG_COM2		0x09
> +#define REG_PID			0x0a	/* Product ID MSB */
> +#define REG_VER			0x0b	/* Product ID LSB */
> +#define REG_COM3		0x0c
> +#define  COM3_SWAP		0x40
> +#define  COM3_VARIOPIXEL1	0x04
> +#define REG_COM4		0x0d	/* Vario Pixels  */
> +#define  COM4_VARIOPIXEL2	0x80
> +#define REG_COM5		0x0e	/* System clock options */
> +#define  COM5_SLAVE_MODE	0x10
> +#define  COM5_SYSTEMCLOCK48MHZ	0x80
> +#define REG_COM6		0x0f	/* HREF & ADBLC options */
> +#define REG_AECH		0x10	/* Exposure value, AEC[9:2] */
> +#define REG_CLKRC		0x11	/* Clock control */
> +#define  CLK_EXT		0x40	/* Use external clock directly */
> +#define  CLK_SCALE		0x3f	/* Mask for internal clock scale */
> +#define REG_COM7		0x12	/* SCCB reset, output format */
> +#define  COM7_RESET		0x80
> +#define  COM7_FMT_MASK		0x38
> +#define  COM7_FMT_VGA		0x40
> +#define	 COM7_FMT_CIF		0x20
> +#define  COM7_FMT_QVGA		0x10
> +#define  COM7_FMT_QCIF		0x08
> +#define	 COM7_RGB		0x04
> +#define	 COM7_YUV		0x00
> +#define	 COM7_BAYER		0x01
> +#define	 COM7_PBAYER		0x05
> +#define REG_COM8		0x13	/* AGC/AEC options */
> +#define  COM8_FASTAEC		0x80	/* Enable fast AGC/AEC */
> +#define  COM8_AECSTEP		0x40	/* Unlimited AEC step size */
> +#define  COM8_BFILT		0x20	/* Band filter enable */
> +#define  COM8_AGC		0x04	/* Auto gain enable */
> +#define  COM8_AWB		0x02	/* White balance enable */
> +#define  COM8_AEC		0x01	/* Auto exposure enable */
> +#define REG_COM9		0x14	/* Gain ceiling */
> +#define  COM9_GAIN_CEIL_MASK	0x70	/* */
> +#define REG_COM10		0x15	/* PCLK, HREF, HSYNC signals polarity */
> +#define  COM10_HSYNC		0x40	/* HSYNC instead of HREF */
> +#define  COM10_PCLK_HB		0x20	/* Suppress PCLK on horiz blank */
> +#define  COM10_HREF_REV		0x08	/* Reverse HREF */
> +#define  COM10_VS_LEAD		0x04	/* VSYNC on clock leading edge */
> +#define  COM10_VS_NEG		0x02	/* VSYNC negative */
> +#define  COM10_HS_NEG		0x01	/* HSYNC negative */
> +#define REG_HSTART		0x17	/* Horiz start high bits */
> +#define REG_HSTOP		0x18	/* Horiz stop high bits */
> +#define REG_VSTART		0x19	/* Vert start high bits */
> +#define REG_VSTOP		0x1a	/* Vert stop high bits */
> +#define REG_PSHFT		0x1b	/* Pixel delay after HREF */
> +#define REG_MIDH		0x1c	/* Manufacturer ID MSB */
> +#define REG_MIDL		0x1d	/* Manufufacturer ID LSB */
> +#define REG_MVFP		0x1e	/* Image mirror/flip */
> +#define  MVFP_MIRROR		0x20	/* Mirror image */
> +#define  MVFP_FLIP		0x10	/* Vertical flip */
> +#define REG_BOS			0x20	/* B channel Offset */
> +#define REG_GBOS		0x21	/* Gb channel Offset */
> +#define REG_GROS		0x22	/* Gr channel Offset */
> +#define REG_ROS			0x23	/* R channel Offset */
> +#define REG_AEW			0x24	/* AGC upper limit */
> +#define REG_AEB			0x25	/* AGC lower limit */
> +#define REG_VPT			0x26	/* AGC/AEC fast mode op region */
> +#define REG_BBIAS		0x27	/* B channel output bias */
> +#define REG_GBBIAS		0x28	/* Gb channel output bias */
> +#define REG_GRCOM		0x29	/* Analog BLC & regulator */
> +#define REG_EXHCH		0x2a	/* Dummy pixel insert MSB */
> +#define REG_EXHCL		0x2b	/* Dummy pixel insert LSB */
> +#define REG_RBIAS		0x2c	/* R channel output bias */
> +#define REG_ADVFL		0x2d	/* LSB of dummy line insert */
> +#define REG_ADVFH		0x2e	/* MSB of dummy line insert */
> +#define REG_YAVE		0x2f	/* Y/G channel average value */
> +#define REG_HSYST		0x30	/* HSYNC rising edge delay LSB*/
> +#define REG_HSYEN		0x31	/* HSYNC falling edge delay LSB*/
> +#define REG_HREF		0x32	/* HREF pieces */
> +#define REG_CHLF		0x33	/* reserved */
> +#define REG_ADC			0x37	/* reserved */
> +#define REG_ACOM		0x38	/* reserved */
> +#define REG_OFON		0x39	/* Power down register */
> +#define  OFON_PWRDN		0x08	/* Power down bit */
> +#define REG_TSLB		0x3a	/* YUVU format */
> +#define  TSLB_YUYV_MASK		0x0c	/* UYVY or VYUY - see com13 */
> +#define REG_COM11		0x3b	/* Night mode, banding filter enable */
> +#define  COM11_NIGHT		0x80	/* Night mode enable */
> +#define  COM11_NMFR		0x60	/* Two bit NM frame rate */
> +#define  COM11_BANDING		0x01	/* Banding filter */
> +#define  COM11_AEC_REF_MASK	0x18	/* AEC reference area selection */
> +#define REG_COM12		0x3c	/* HREF option, UV average */
> +#define  COM12_HREF		0x80	/* HREF always */
> +#define REG_COM13		0x3d	/* Gamma selection, Color matrix en. */
> +#define  COM13_GAMMA		0x80	/* Gamma enable */
> +#define	 COM13_UVSAT		0x40	/* UV saturation auto adjustment */
> +#define  COM13_UVSWAP		0x01	/* V before U - w/TSLB */
> +#define REG_COM14		0x3e	/* Edge enhancement options */
> +#define  COM14_EDGE_EN		0x02
> +#define  COM14_EEF_X2		0x01
> +#define REG_EDGE		0x3f	/* Edge enhancement factor */
> +#define  EDGE_FACTOR_MASK	0x0f
> +#define REG_COM15		0x40	/* Output range, RGB 555/565 */
> +#define  COM15_R10F0		0x00	/* Data range 10 to F0 */
> +#define	 COM15_R01FE		0x80	/* 01 to FE */
> +#define  COM15_R00FF		0xc0	/* 00 to FF */
> +#define  COM15_RGB565		0x10	/* RGB565 output */
> +#define  COM15_RGB555		0x30	/* RGB555 output */
> +#define  COM15_SWAPRB		0x04	/* Swap R&B */
> +#define REG_COM16		0x41	/* Color matrix coeff options */
> +#define REG_COM17		0x42	/* Single frame out, banding filter */
> +/* n = 1...9, 0x4f..0x57 */
> +#define	REG_MTX(__n)		(0x4f + (__n) - 1)
> +#define REG_MTXS		0x58
> +/* Lens Correction Option 1...5, __n = 0...5 */
> +#define REG_LCC(__n)		(0x62 + (__n) - 1)
> +#define  LCC5_LCC_ENABLE	0x01	/* LCC5, enable lens correction */
> +#define  LCC5_LCC_COLOR		0x04
> +#define REG_MANU		0x67	/* Manual U value */
> +#define REG_MANV		0x68	/* Manual V value */
> +#define REG_HV			0x69	/* Manual banding filter MSB */
> +#define REG_MBD			0x6a	/* Manual banding filter value */
> +#define REG_DBLV		0x6b	/* reserved */
> +#define REG_GSP			0x6c	/* Gamma curve */
> +#define  GSP_LEN		15
> +#define REG_GST			0x7c	/* Gamma curve */
> +#define  GST_LEN		15
> +#define REG_COM21		0x8b
> +#define REG_COM22		0x8c	/* Edge enhancement, denoising */
> +#define  COM22_WHTPCOR		0x02	/* White pixel correction enable */
> +#define  COM22_WHTPCOROPT	0x01	/* White pixel correction option */
> +#define  COM22_DENOISE		0x10	/* White pixel correction option */
> +#define REG_COM23		0x8d	/* Color bar test, color gain */
> +#define  COM23_TEST_MODE	0x10
> +#define REG_DBLC1		0x8f	/* Digital BLC */
> +#define REG_DBLC_B		0x90	/* Digital BLC B channel offset */
> +#define REG_DBLC_R		0x91	/* Digital BLC R channel offset */
> +#define REG_DM_LNL		0x92	/* Dummy line low 8 bits */
> +#define REG_DM_LNH		0x93	/* Dummy line high 8 bits */
> +#define REG_LCCFB		0x9d	/* Lens Correction B channel */
> +#define REG_LCCFR		0x9e	/* Lens Correction R channel */
> +#define REG_DBLC_GB		0x9f	/* Digital BLC GB chan offset */
> +#define REG_DBLC_GR		0xa0	/* Digital BLC GR chan offset */
> +#define REG_AECHM		0xa1	/* Exposure value - bits AEC[15:10] */
> +#define REG_BD50ST		0xa2	/* Banding filter value for 50Hz */
> +#define REG_BD60ST		0xa3	/* Banding filter value for 60Hz */
> +#define REG_NULL		0xff	/* Array end token */
> +
> +#define DEF_CLKRC		0x80
> +
> +#define OV965X_ID(_msb, _lsb)	((_msb) << 8 | (_lsb))
> +#define OV9650_ID		0x9650
> +#define OV9652_ID		0x9652
> +
> +/* V4L2 private controls */
> +
> +/* Auto exposure frame reference area */
> +#define V4L2_CID_EXPOSURE_REFERENCE_AREA (V4L2_CTRL_CLASS_CAMERA | 0x1001)
> +/* Maximum gain value */
> +#define V4L2_CID_GAIN_CEILING		 (V4L2_CTRL_CLASS_CAMERA | 0x1002)

Private controls should be added to uapi/linux/v4l2-controls.h. By having
all controls in the same header it is easy to ensure that there are no
duplicate IDs in use.

The name of the driver should be part of the control name, so something like:

V4L2_CID_OV9650_EXP_REFERENCE_AREA
V4L2_CID_OV9650_GAIN_CEILING

> +/* V4L2 controls flags for volatile, read-only control */
> +#define CTRL_FLAG_READ_ONLY_VOLATILE	 (V4L2_CTRL_FLAG_READ_ONLY | \
> +					  V4L2_CTRL_FLAG_VOLATILE)
> +
> +struct ov965x_ctrls {
> +	struct v4l2_ctrl_handler handler;
> +	struct {
> +		struct v4l2_ctrl *auto_exp;
> +		struct v4l2_ctrl *exposure;
> +		struct v4l2_ctrl *ae_frame_area;
> +	};
> +	struct {
> +		struct v4l2_ctrl *auto_wb;
> +		struct v4l2_ctrl *blue_balance;
> +		struct v4l2_ctrl *red_balance;
> +	};
> +	struct {
> +		struct v4l2_ctrl *hflip;
> +		struct v4l2_ctrl *vflip;
> +	};
> +	struct {
> +		struct v4l2_ctrl *auto_gain;
> +		struct v4l2_ctrl *gain;
> +		struct v4l2_ctrl *gain_ceiling;
> +	};
> +	struct v4l2_ctrl *brightness;
> +	struct v4l2_ctrl *contrast;
> +	struct v4l2_ctrl *saturation;
> +	struct v4l2_ctrl *sharpness;
> +	struct v4l2_ctrl *light_freq;
> +	u8 update;
> +};
> +
> +struct ov965x_framesize {
> +	u16 width;
> +	u16 height;
> +	u16 max_exp_lines;
> +	const u8 *regs;
> +};
> +
> +struct ov965x_interval {
> +	struct v4l2_fract interval;
> +	/* Maximum resolution for this interval */
> +	struct v4l2_frmsize_discrete size;
> +	u8 clkrc_div;
> +};
> +
> +enum gpio_id {
> +	GPIO_PWDN,
> +	GPIO_RST,
> +	NUM_GPIOS,
> +};
> +
> +struct ov965x {
> +	struct v4l2_subdev sd;
> +	struct media_pad pad;
> +	enum v4l2_mbus_type bus_type;
> +	int gpios[NUM_GPIOS];
> +	/* External master clock frequency */
> +	unsigned long mclk_frequency;
> +
> +	/* Protects the struct fields below */
> +	struct mutex lock;
> +
> +	struct i2c_client *client;
> +
> +	/* Exposure row interval in us */
> +	unsigned int exp_row_interval;
> +
> +	unsigned short id;
> +	const struct ov965x_framesize *frame_size;
> +	/* YUYV sequence (pixel format) control register */
> +	u8 tslb_reg;
> +	struct v4l2_mbus_framefmt format;
> +
> +	struct ov965x_ctrls ctrls;
> +	/* Pointer to frame rate control data structure */
> +	const struct ov965x_interval *fiv;
> +
> +	int streaming;
> +	int power;
> +
> +	u8 apply_frame_fmt;
> +};
> +
> +struct i2c_rv {
> +	u8 addr;
> +	u8 value;
> +};
> +
> +static const struct i2c_rv ov965x_init_regs[] = {
> +	{ REG_COM2, 0x10 },	/* Set soft sleep mode */
> +	{ REG_COM5, 0x00 },	/* System clock options */
> +	{ REG_COM2, 0x01 },	/* Output drive, soft sleep mode */
> +	{ REG_COM10, 0x00 },	/* Slave mode, HREF vs HSYNC, signals negate */
> +	{ REG_EDGE, 0xa6 },	/* Edge enhancement treshhold and factor */
> +	{ REG_COM16, 0x02 },	/* Color matrix coeff double option */
> +	{ REG_COM17, 0x08 },	/* Single frame out, banding filter */
> +	{ 0x16, 0x06 },
> +	{ REG_CHLF, 0xc0 },	/* Reserved  */
> +	{ 0x34, 0xbf },
> +	{ 0xa8, 0x80 },
> +	{ 0x96, 0x04 },
> +	{ 0x8e, 0x00 },
> +	{ REG_COM12, 0x77 },	/* HREF option, UV average  */
> +	{ 0x8b, 0x06 },
> +	{ 0x35, 0x91 },
> +	{ 0x94, 0x88 },
> +	{ 0x95, 0x88 },
> +	{ REG_COM15, 0xc1 },	/* Output range, RGB 555/565 */
> +	{ REG_GRCOM, 0x2f },	/* Analog BLC & regulator */
> +	{ REG_COM6, 0x43 },	/* HREF & ADBLC options */
> +	{ REG_COM8, 0xe5 },	/* AGC/AEC options */
> +	{ REG_COM13, 0x90 },	/* Gamma selection, colour matrix, UV delay */
> +	{ REG_HV, 0x80 },	/* Manual banding filter MSB  */
> +	{ 0x5c, 0x96 },		/* Reserved up to 0xa5 */
> +	{ 0x5d, 0x96 },
> +	{ 0x5e, 0x10 },
> +	{ 0x59, 0xeb },
> +	{ 0x5a, 0x9c },
> +	{ 0x5b, 0x55 },
> +	{ 0x43, 0xf0 },
> +	{ 0x44, 0x10 },
> +	{ 0x45, 0x55 },
> +	{ 0x46, 0x86 },
> +	{ 0x47, 0x64 },
> +	{ 0x48, 0x86 },
> +	{ 0x5f, 0xe0 },
> +	{ 0x60, 0x8c },
> +	{ 0x61, 0x20 },
> +	{ 0xa5, 0xd9 },
> +	{ 0xa4, 0x74 },		/* reserved */
> +	{ REG_COM23, 0x02 },	/* Color gain analog/_digital_ */
> +	{ REG_COM8, 0xe7 },	/* Enable AEC, AWB, AEC */
> +	{ REG_COM22, 0x23 },	/* Edge enhancement, denoising */
> +	{ 0xa9, 0xb8 },
> +	{ 0xaa, 0x92 },
> +	{ 0xab, 0x0a },
> +	{ REG_DBLC1, 0xdf },	/* Digital BLC */
> +	{ REG_DBLC_B, 0x00 },	/* Digital BLC B chan offset */
> +	{ REG_DBLC_R, 0x00 },	/* Digital BLC R chan offset */
> +	{ REG_DBLC_GB, 0x00 },	/* Digital BLC GB chan offset */
> +	{ REG_DBLC_GR, 0x00 },
> +	{ REG_NULL, 0 }
> +};
> +
> +#define NUM_FMT_REGS 14
> +/*
> + * COM7,  COM3,  COM4, HSTART, HSTOP, HREF, VSTART, VSTOP, VREF,
> + * EXHCH, EXHCL, ADC,  OCOM,   OFON
> + */
> +static const u8 frame_size_reg_addr[NUM_FMT_REGS] = {
> +	0x12, 0x0c, 0x0d, 0x17, 0x18, 0x32, 0x19, 0x1a, 0x03,
> +	0x2a, 0x2b, 0x37, 0x38, 0x39,
> +};
> +
> +static const u8 ov965x_sxga_regs[NUM_FMT_REGS] = {
> +	0x00, 0x00, 0x00, 0x1e, 0xbe, 0xbf, 0x01, 0x81, 0x12,
> +	0x10, 0x34, 0x81, 0x93, 0x51,
> +};
> +
> +static const u8 ov965x_vga_regs[NUM_FMT_REGS] = {
> +	0x40, 0x04, 0x80, 0x26, 0xc6, 0xed, 0x01, 0x3d, 0x00,
> +	0x10, 0x40, 0x91, 0x12, 0x43,
> +};
> +
> +/* Determined empirically. */
> +static const u8 ov965x_qvga_regs[NUM_FMT_REGS] = {
> +	0x10, 0x04, 0x80, 0x25, 0xc5, 0xbf, 0x00, 0x80, 0x12,
> +	0x10, 0x40, 0x91, 0x12, 0x43,
> +};
> +
> +static const struct ov965x_framesize ov965x_framesizes[] = {
> +	{
> +		.width		= SXGA_WIDTH,
> +		.height		= SXGA_HEIGHT,
> +		.regs		= ov965x_sxga_regs,
> +		.max_exp_lines	= 1048,
> +	}, {
> +		.width		= VGA_WIDTH,
> +		.height		= VGA_HEIGHT,
> +		.regs		= ov965x_vga_regs,
> +		.max_exp_lines	= 498,
> +	}, {
> +		.width		= QVGA_WIDTH,
> +		.height		= QVGA_HEIGHT,
> +		.regs		= ov965x_qvga_regs,
> +		.max_exp_lines	= 248,
> +	},
> +};
> +
> +struct ov965x_pixfmt {
> +	enum v4l2_mbus_pixelcode code;
> +	u32 colorspace;
> +	/* REG_TSLB value, only bits [3:2] may be set. */
> +	u8 tslb_reg;
> +};
> +
> +static const struct ov965x_pixfmt ov965x_formats[] = {
> +	{ V4L2_MBUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG, 0x00},
> +	{ V4L2_MBUS_FMT_YVYU8_2X8, V4L2_COLORSPACE_JPEG, 0x04},
> +	{ V4L2_MBUS_FMT_UYVY8_2X8, V4L2_COLORSPACE_JPEG, 0x0c},
> +	{ V4L2_MBUS_FMT_VYUY8_2X8, V4L2_COLORSPACE_JPEG, 0x08},
> +};
> +
> +/*
> + * This table specifies possible frame resolution and interval
> + * combinations. Default CLKRC[5:0] divider values are valid
> + * only for 24 MHz external clock frequency.
> + */
> +static struct ov965x_interval ov965x_intervals[] = {
> +	{{ 100, 625 }, { SXGA_WIDTH, SXGA_HEIGHT }, 0 },  /* 6.25 fps */
> +	{{ 10,  125 }, { VGA_WIDTH, VGA_HEIGHT },   1 },  /* 12.5 fps */
> +	{{ 10,  125 }, { QVGA_WIDTH, QVGA_HEIGHT }, 3 },  /* 12.5 fps */
> +	{{ 1,   25  }, { VGA_WIDTH, VGA_HEIGHT },   0 },  /* 25 fps */
> +	{{ 1,   25  }, { QVGA_WIDTH, QVGA_HEIGHT }, 1 },  /* 25 fps */
> +};
> +
> +static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
> +{
> +	return &container_of(ctrl->handler, struct ov965x, ctrls.handler)->sd;
> +}
> +
> +static inline struct ov965x *to_ov965x(struct v4l2_subdev *sd)
> +{
> +	return container_of(sd, struct ov965x, sd);
> +}
> +
> +static int ov965x_read(struct i2c_client *client, u8 addr, u8 *val)
> +{
> +	u8 buf = addr;
> +	struct i2c_msg msg = {
> +		.addr = client->addr,
> +		.flags = 0,
> +		.len = 1,
> +		.buf = &buf
> +	};
> +	int ret;
> +
> +	ret = i2c_transfer(client->adapter, &msg, 1);
> +	if (ret == 1) {
> +		msg.flags = I2C_M_RD;
> +		ret = i2c_transfer(client->adapter, &msg, 1);
> +
> +		if (ret == 1)
> +			*val = buf;
> +	}
> +
> +	v4l2_dbg(2, debug, client, "%s: 0x%02x @ 0x%02x. (%d)\n",
> +		 __func__, *val, addr, ret);
> +
> +	return ret == 1 ? 0 : ret;
> +}
> +
> +static int ov965x_write(struct i2c_client *client, u8 addr, u8 val)
> +{
> +	u8 buf[2] = { addr, val };
> +
> +	int ret = i2c_master_send(client, buf, 2);
> +
> +	v4l2_dbg(2, debug, client, "%s: 0x%02x @ 0x%02X (%d)\n",
> +		 __func__, val, addr, ret);
> +
> +	return ret == 2 ? 0 : ret;
> +}
> +
> +static int ov965x_write_array(struct i2c_client *client,
> +			      const struct i2c_rv *regs)
> +{
> +	int i, ret = 0;
> +
> +	for (i = 0; ret == 0 && regs[i].addr != REG_NULL; i++)
> +		ret = ov965x_write(client, regs[i].addr, regs[i].value);
> +
> +	return ret;
> +}
> +
> +static int ov965x_set_default_gamma_curve(struct ov965x *ov965x)
> +{
> +	static const u8 gamma_curve[] = {
> +		/* Values taken from OV application note. */
> +		0x40, 0x30, 0x4b, 0x60, 0x70, 0x70, 0x70, 0x70,
> +		0x60, 0x60, 0x50, 0x48, 0x3a, 0x2e, 0x28, 0x22,
> +		0x04, 0x07, 0x10, 0x28,	0x36, 0x44, 0x52, 0x60,
> +		0x6c, 0x78, 0x8c, 0x9e, 0xbb, 0xd2, 0xe6
> +	};
> +	u8 addr = REG_GSP;
> +	unsigned int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(gamma_curve); i++) {
> +		int ret = ov965x_write(ov965x->client, addr, gamma_curve[i]);
> +		if (ret < 0)
> +			return ret;
> +		addr++;
> +	}
> +
> +	return 0;
> +};
> +
> +static int ov965x_set_color_matrix(struct ov965x *ov965x)
> +{
> +	static const u8 mtx[] = {
> +		/* MTX1..MTX9, MTXS */
> +		0x3a, 0x3d, 0x03, 0x12, 0x26, 0x38, 0x40, 0x40, 0x40, 0x0d
> +	};
> +	u8 addr = REG_MTX(1);
> +	unsigned int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(mtx); i++) {
> +		int ret = ov965x_write(ov965x->client, addr, mtx[i]);
> +		if (ret < 0)
> +			return ret;
> +		addr++;
> +	}
> +
> +	return 0;
> +}
> +
> +static void ov965x_gpio_set(int gpio, int val)
> +{
> +	if (gpio_is_valid(gpio))
> +		gpio_set_value(gpio, val);
> +}
> +
> +static void __ov965x_set_power(struct ov965x *ov965x, int on)
> +{
> +	if (on) {
> +		ov965x_gpio_set(ov965x->gpios[GPIO_PWDN], 0);
> +		ov965x_gpio_set(ov965x->gpios[GPIO_RST], 0);
> +		usleep_range(25000, 26000);
> +	} else {
> +		ov965x_gpio_set(ov965x->gpios[GPIO_RST], 1);
> +		ov965x_gpio_set(ov965x->gpios[GPIO_PWDN], 1);
> +	}
> +
> +	ov965x->streaming = 0;
> +}
> +
> +static int ov965x_s_power(struct v4l2_subdev *sd, int on)
> +{
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	struct i2c_client *client = ov965x->client;
> +	int ret = 0;
> +
> +	v4l2_dbg(1, debug, client, "%s: on: %d\n", __func__, on);
> +
> +	mutex_lock(&ov965x->lock);
> +	if (ov965x->power == !on) {
> +		__ov965x_set_power(ov965x, on);
> +		if (on) {
> +			ret = ov965x_write_array(client,
> +						 ov965x_init_regs);
> +			ov965x->apply_frame_fmt = 1;
> +			ov965x->ctrls.update = 1;
> +		}
> +	}
> +	if (!ret)
> +		ov965x->power += on ? 1 : -1;
> +
> +	WARN_ON(ov965x->power < 0);
> +	mutex_unlock(&ov965x->lock);
> +	return ret;
> +}
> +
> +/*
> + * V4L2 controls
> + */
> +
> +static void ov965x_update_exposure_ctrl(struct ov965x *ov965x)
> +{
> +	struct v4l2_ctrl *ctrl = ov965x->ctrls.exposure;
> +	unsigned long fint, trow;
> +	int max;
> +	u8 clkrc;
> +
> +	mutex_lock(&ov965x->lock);
> +
> +	if (WARN_ON(!ctrl || !ov965x->frame_size)) {
> +		mutex_unlock(&ov965x->lock);
> +		return;
> +	}
> +	clkrc = DEF_CLKRC + ov965x->fiv->clkrc_div;
> +	/* Calculate internal clock frequency */
> +	fint = ov965x->mclk_frequency * ((clkrc >> 7) + 1) /
> +				((2 * ((clkrc & 0x3f) + 1)));
> +	/* and the row interval (in us). */
> +	trow = (2 * 1520 * 1000000UL) / fint;
> +	max = ov965x->frame_size->max_exp_lines * trow;
> +	ov965x->exp_row_interval = trow;
> +
> +	mutex_unlock(&ov965x->lock);
> +	v4l2_dbg(1, debug, &ov965x->sd, "clkrc: %#x, fi: %lu, tr: %lu, %d\n",
> +		 clkrc, fint, trow, max);
> +
> +	/* Update exposure time min/max to match current frame format. */
> +	v4l2_ctrl_lock(ctrl);
> +
> +	ctrl->minimum = (trow + 100) / 100;
> +	ctrl->maximum = (max - 100) / 100;
> +	if (ctrl->cur.val > ctrl->maximum)
> +		ctrl->cur.val = ctrl->maximum;
> +	if (ctrl->cur.val < ctrl->minimum)
> +		ctrl->cur.val = ctrl->minimum;

You can't do this like that. To do this correctly you need to create a new
function in v4l2-ctrl.c that allows you to change the control attributes
minimum, maximum, step and default_value.

That function can then call send_event() to tell external apps that these
attributes have changed. That also requires a new flag V4L2_EVENT_CTRL_CH_RANGE.

v4l2_ctrl_modify_range() would probably be a good name for such a function.

> +
> +	v4l2_ctrl_unlock(ctrl);
> +}
> +
> +static int ov965x_set_banding_filter(struct ov965x *ov965x, int value)
> +{
> +	unsigned long mbd, light_freq;
> +	int ret;
> +	u8 reg;
> +
> +	ret = ov965x_read(ov965x->client, REG_COM8, &reg);
> +	if (!ret) {
> +		if (value == V4L2_CID_POWER_LINE_FREQUENCY_DISABLED)
> +			reg &= ~COM8_BFILT;
> +		else
> +			reg |= COM8_BFILT;
> +		ret = ov965x_write(ov965x->client, REG_COM8, reg);
> +	}
> +	if (value == V4L2_CID_POWER_LINE_FREQUENCY_DISABLED)
> +		return 0;
> +	if (WARN_ON(ov965x->fiv == NULL))
> +		return -EINVAL;
> +	/* Set minimal exposure time for 50/60 HZ lighting */
> +	if (value == V4L2_CID_POWER_LINE_FREQUENCY_50HZ)
> +		light_freq = 50;
> +	else
> +		light_freq = 60;
> +	mbd = (1000UL * ov965x->fiv->interval.denominator *
> +	       ov965x->frame_size->max_exp_lines) /
> +	       ov965x->fiv->interval.numerator;
> +	mbd = ((mbd / (light_freq * 2)) + 500) / 1000UL;
> +
> +	return ov965x_write(ov965x->client, REG_MBD, mbd);
> +}
> +
> +static int ov965x_set_white_balance(struct ov965x *ov965x, int awb)
> +{
> +	int ret;
> +	u8 reg;
> +
> +	ret = ov965x_read(ov965x->client, REG_COM8, &reg);
> +	if (!ret) {
> +		reg = awb ? reg | REG_COM8 : reg & ~REG_COM8;
> +		ret = ov965x_write(ov965x->client, REG_COM8, reg);
> +	}
> +	if (!ret && !awb) {
> +		ret = ov965x_write(ov965x->client, REG_BLUE,
> +				   ov965x->ctrls.blue_balance->val);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov965x_write(ov965x->client, REG_RED,
> +				   ov965x->ctrls.red_balance->val);
> +	}
> +	return ret;
> +}
> +
> +#define NUM_BR_LEVELS	7
> +#define NUM_BR_REGS	3
> +
> +static int ov965x_set_brightness(struct ov965x *ov965x, int val)
> +{
> +	static const u8 regs[NUM_BR_LEVELS + 1][NUM_BR_REGS] = {
> +		{ REG_AEW, REG_AEB, REG_VPT },
> +		{ 0x1c, 0x12, 0x50 }, /* -3 */
> +		{ 0x3d, 0x30, 0x71 }, /* -2 */
> +		{ 0x50, 0x44, 0x92 }, /* -1 */
> +		{ 0x70, 0x64, 0xc3 }, /*  0 */
> +		{ 0x90, 0x84, 0xd4 }, /* +1 */
> +		{ 0xc4, 0xbf, 0xf9 }, /* +2 */
> +		{ 0xd8, 0xd0, 0xfa }, /* +3 */
> +	};
> +	int i, ret = 0;
> +
> +	val += (NUM_BR_LEVELS / 2 + 1);
> +	if (val > NUM_BR_LEVELS)
> +		return -EINVAL;
> +
> +	for (i = 0; i < NUM_BR_REGS && !ret; i++)
> +		ret = ov965x_write(ov965x->client, regs[0][i],
> +				   regs[val][i]);
> +	return ret;
> +}
> +
> +static int ov965x_set_contrast(struct ov965x *ov965x, int value)
> +{
> +	/* TODO */
> +	return -EINVAL;
> +}

Perhaps this should just be removed?

> +static int ov965x_set_gain(struct ov965x *ov965x, int auto_gain, bool init)
> +{
> +	struct i2c_client *client = ov965x->client;
> +	struct ov965x_ctrls *ctrls = &ov965x->ctrls;
> +	int ret = 0;
> +	u8 reg;
> +	/*
> +	 * For manual mode we need to disable AGC first, so
> +	 * gain value in REG_VREF, REG_GAIN is not overwritten.
> +	 */
> +	if (ctrls->auto_gain->is_new || init) {
> +		ret = ov965x_read(client, REG_COM8, &reg);
> +		if (ret < 0)
> +			return ret;
> +		if (ctrls->auto_gain->val)
> +			reg |= COM8_AGC;
> +		else
> +			reg &= ~COM8_AGC;
> +		ret = ov965x_write(client, REG_COM8, reg);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	if ((ctrls->gain->is_new || init) && !auto_gain) {
> +		unsigned int gain = ctrls->gain->val;
> +		unsigned int rgain;
> +		int m;
> +		/*
> +		 * Convert gain control value to the sensor's gain
> +		 * registers (VREF[7:6], GAIN[7:0]) format.
> +		 */
> +		for (m = 6; m >= 0; m--)
> +			if (gain >= (1 << m) * 16)
> +				break;
> +		rgain = (gain - ((1 << m) * 16)) / (1 << m);
> +		rgain |= (((1 << m) - 1) << 4);
> +
> +		ret = ov965x_write(client, REG_GAIN, rgain & 0xff);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov965x_read(client, REG_VREF, &reg);
> +		if (ret < 0)
> +			return ret;
> +		reg &= ~VREF_GAIN_MASK;
> +		reg |= (((rgain >> 8) & 0x3) << 6);
> +		ret = ov965x_write(client, REG_VREF, reg);
> +		if (ret < 0)
> +			return ret;
> +		/* Return updated control's value to userspace */
> +		ctrls->gain->val = (1 << m) * (16 + (rgain & 0xf));
> +	}
> +
> +	if (ctrls->gain_ceiling->is_new || init) {
> +		u8 gc = ctrls->gain_ceiling->val;
> +		ret = ov965x_read(client, REG_COM9, &reg);
> +		if (!ret) {
> +			reg &= ~COM9_GAIN_CEIL_MASK;
> +			reg |= ((gc & 0x07) << 4);
> +			ret = ov965x_write(client, REG_COM9, reg);
> +		}
> +	}
> +	if (auto_gain)
> +		ctrls->gain->flags |= CTRL_FLAG_READ_ONLY_VOLATILE;
> +	else
> +		ctrls->gain->flags &= ~CTRL_FLAG_READ_ONLY_VOLATILE;
> +
> +	return ret;
> +}
> +
> +static int ov965x_set_sharpness(struct ov965x *ov965x, unsigned int value)
> +{
> +	u8 com14, edge;
> +	int ret;
> +
> +	ret = ov965x_read(ov965x->client, REG_COM14, &com14);
> +	if (ret < 0)
> +		return ret;
> +	ret = ov965x_read(ov965x->client, REG_EDGE, &edge);
> +	if (ret < 0)
> +		return ret;
> +	com14 = value ? com14 | COM14_EDGE_EN : com14 & ~COM14_EDGE_EN;
> +	value--;
> +	if (value > 0x0f) {
> +		com14 |= COM14_EEF_X2;
> +		value >>= 1;
> +	} else {
> +		com14 &= ~COM14_EEF_X2;
> +	}
> +	ret = ov965x_write(ov965x->client, REG_COM14, com14);
> +	if (ret < 0)
> +		return ret;
> +
> +	edge &= ~EDGE_FACTOR_MASK;
> +	edge |= ((u8)value & 0x0f);
> +
> +	return ov965x_write(ov965x->client, REG_EDGE, edge);
> +}
> +
> +static int ov965x_set_exposure(struct ov965x *ov965x, int exp, bool init)
> +{
> +	struct i2c_client *client = ov965x->client;
> +	struct ov965x_ctrls *ctrls = &ov965x->ctrls;
> +	bool auto_exposure = (exp == V4L2_EXPOSURE_AUTO);
> +	int ret;
> +	u8 reg;
> +
> +	if (ctrls->auto_exp->is_new || init) {
> +		ret = ov965x_read(client, REG_COM8, &reg);
> +		if (ret < 0)
> +			return ret;
> +		if (auto_exposure)
> +			reg |= (COM8_AEC | COM8_AGC);
> +		else
> +			reg &= ~(COM8_AEC | COM8_AGC);
> +		ret = ov965x_write(client, REG_COM8, reg);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	if (!auto_exposure && (ctrls->exposure->is_new || init)) {
> +		unsigned int exposure = (ctrls->exposure->val * 100)
> +					 / ov965x->exp_row_interval;
> +		/*
> +		 * Manual exposure value
> +		 * [b15:b0] - AECHM (b15:b10), AECH (b9:b2), COM1 (b1:b0)
> +		 */
> +		ret = ov965x_write(client, REG_COM1, exposure & 0x3);
> +		if (!ret)
> +			ret = ov965x_write(client, REG_AECH,
> +					   (exposure >> 2) & 0xff);
> +		if (!ret)
> +			ret = ov965x_write(client, REG_AECHM,
> +					   (exposure >> 10) & 0x3f);
> +		/* Update the value to minimize rounding errors */
> +		ctrls->exposure->val = ((exposure * ov965x->exp_row_interval)
> +							+ 50) / 100;
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	if (ctrls->ae_frame_area->is_new || init) {
> +		ret = ov965x_read(client, REG_COM11, &reg);
> +		if (ret < 0)
> +			return ret;
> +		reg &= ~COM11_AEC_REF_MASK;
> +		reg |= ((ctrls->ae_frame_area->val & 0x3) << 3);
> +		ret = ov965x_write(client, REG_COM11, reg);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	if (auto_exposure)
> +		ctrls->exposure->flags |= CTRL_FLAG_READ_ONLY_VOLATILE;
> +	else
> +		ctrls->exposure->flags &= ~CTRL_FLAG_READ_ONLY_VOLATILE;
> +
> +	v4l2_ctrl_activate(ov965x->ctrls.brightness, !exp);
> +	return 0;
> +}
> +
> +static int ov965x_set_flip(struct ov965x *ov965x)
> +{
> +	u8 mvfp = 0;
> +
> +	if (ov965x->ctrls.hflip->val)
> +		mvfp |= MVFP_MIRROR;
> +
> +	if (ov965x->ctrls.vflip->val)
> +		mvfp |= MVFP_FLIP;
> +
> +	return ov965x_write(ov965x->client, REG_MVFP, mvfp);
> +}
> +
> +#define NUM_SAT_LEVELS	5
> +#define NUM_SAT_REGS	6
> +
> +static int ov965x_set_saturation(struct ov965x *ov965x, int val)
> +{
> +	static const u8 regs[NUM_SAT_LEVELS][NUM_SAT_REGS] = {
> +		/* MTX(1)...MTX(6) */
> +		{ 0x1d, 0x1f, 0x02, 0x09, 0x13, 0x1c }, /* -2 */
> +		{ 0x2e, 0x31, 0x02, 0x0e, 0x1e, 0x2d }, /* -1 */
> +		{ 0x3a, 0x3d, 0x03, 0x12, 0x26, 0x38 }, /*  0 */
> +		{ 0x46, 0x49, 0x04, 0x16, 0x2e, 0x43 }, /* +1 */
> +		{ 0x57, 0x5c, 0x05, 0x1b, 0x39, 0x54 }, /* +2 */
> +	};
> +	u8 addr = REG_MTX(1);
> +	int i, ret = 0;
> +
> +	val += (NUM_SAT_LEVELS / 2);
> +	if (val >= NUM_SAT_LEVELS)
> +		return -EINVAL;
> +
> +	for (i = 0; i < NUM_SAT_REGS && !ret; i++)
> +		ret = ov965x_write(ov965x->client, addr + i, regs[val][i]);
> +
> +	return ret;
> +}
> +
> +static int ov965x_set_test_pattern(struct ov965x *ov965x, int value)
> +{
> +	int ret;
> +	u8 reg;
> +
> +	ret = ov965x_read(ov965x->client, REG_COM23, &reg);
> +	if (ret < 0)
> +		return ret;
> +	reg = value ? reg | COM23_TEST_MODE : reg & ~COM23_TEST_MODE;
> +	return ov965x_write(ov965x->client, REG_COM23, reg);
> +}
> +
> +/*
> + * Configure sensor register to match default control values. We can't use
> + * v4l2_ctrl_handler_setup() here as s_ctrl() also takes ov965x->lock mutex.

I don't think it is a good idea to do it like this. It's much better to call
v4l2_ctrl_handler_setup directly unless there are really good reasons for not
doing that.

With regards to the locking: I think you might need two locks here: one that
protects struct ov965x and one that is used to serialize between calls from
a bridge driver and calls directly to the subdev file handle (although I am
not certain the latter lock is needed at all).

In this case I think ov965x->lock shouldn't be held, and v4l2_ctrl_handler_setup
should be called.

> + * Also, explicit function calls allow to better specify the register write
> + * sequence.
> + */
> +static int __ov965x_restore_controls(struct ov965x *ov965x)
> +{
> +	struct ov965x_ctrls *ctrls = &ov965x->ctrls;
> +	int ret;
> +
> +	ret = ov965x_set_gain(ov965x, ctrls->auto_gain->val, true);
> +	if (!ret)
> +		ret = ov965x_set_brightness(ov965x, ctrls->brightness->val);
> +	if (!ret)
> +		ret = ov965x_set_exposure(ov965x, ctrls->auto_exp->val, true);
> +	if (!ret)
> +		ret = ov965x_set_sharpness(ov965x, ctrls->sharpness->val);
> +	if (!ret)
> +		ret = ov965x_set_saturation(ov965x, ctrls->saturation->val);
> +	if (!ret)
> +		ret = ov965x_set_white_balance(ov965x, ctrls->auto_wb->val);
> +
> +	return ret;
> +}
> +
> +static int __g_volatile_ctrl(struct ov965x *ov965x, struct v4l2_ctrl *ctrl)
> +{
> +	struct i2c_client *client = ov965x->client;
> +	unsigned int exposure, gain, m;
> +	u8 reg0, reg1, reg2;
> +	int ret;
> +
> +	if (!ov965x->power)
> +		return -EAGAIN;

How about 'return 0;'? If the power is off, then it seems reasonable to
just return the last gain/exposure value. Without power the autogain and
autoexposure hardware is turned off as well, so gain and exposure aren't
updated.

I mention this because EAGAIN suggests that you can just try it again a bit
later, but that won't help as long as the power isn't turned on.

> +
> +	switch (ctrl->id) {
> +	case V4L2_CID_AUTOGAIN:
> +		if (!ctrl->val)
> +			return 0;
> +		ret = ov965x_read(client, REG_GAIN, &reg0);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov965x_read(client, REG_VREF, &reg1);
> +		if (ret < 0)
> +			return ret;
> +		gain = ((reg1 >> 6) << 8) | reg0;
> +		m = 0x01 << fls(gain >> 4);
> +		ov965x->ctrls.gain->val = m * (16 + (gain & 0xf));
> +		break;
> +
> +	case V4L2_CID_EXPOSURE_AUTO:
> +		if (ctrl->val == V4L2_EXPOSURE_MANUAL)
> +			return 0;
> +		ret = ov965x_read(client, REG_COM1, &reg0);
> +		if (!ret)
> +			ret = ov965x_read(client, REG_AECH, &reg1);
> +		if (!ret)
> +			ret = ov965x_read(client, REG_AECHM, &reg2);
> +		if (ret < 0)
> +			return ret;
> +		exposure = ((reg2 & 0x3f) << 10) | (reg1 << 2) |
> +						(reg0 & 0x3);
> +		ov965x->ctrls.exposure->val = ((exposure *
> +				ov965x->exp_row_interval) + 50) / 100;
> +		break;
> +	}
> +
> +	return 0;
> +}
> +
> +static int ov965x_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
> +{
> +	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	int ret;
> +
> +	v4l2_dbg(1, debug, sd, "g_ctrl: %s\n", ctrl->name);
> +
> +	mutex_lock(&ov965x->lock);
> +	ret = __g_volatile_ctrl(ov965x, ctrl);
> +	mutex_unlock(&ov965x->lock);
> +	return ret;
> +}
> +
> +static int ov965x_s_ctrl(struct v4l2_ctrl *ctrl)
> +{
> +	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	int ret = -EINVAL;
> +
> +	v4l2_dbg(1, debug, sd, "s_ctrl: %s, value: %d. power: %d\n",
> +		 ctrl->name, ctrl->val, ov965x->power);
> +
> +	if (ctrl->flags & V4L2_CTRL_FLAG_INACTIVE)
> +		return 0;

You should not need this if you use the auto_cluster support.

> +	mutex_lock(&ov965x->lock);
> +	/*
> +	 * If the device is not powered up now postpone applying control's
> +	 * value to the hardware, until it is ready to accept commands.
> +	 */
> +	if (ov965x->power == 0) {
> +		mutex_unlock(&ov965x->lock);
> +		return 0;
> +	}
> +
> +	switch (ctrl->id) {
> +	case V4L2_CID_AUTO_WHITE_BALANCE:
> +		ret = ov965x_set_white_balance(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_BRIGHTNESS:
> +		ret = ov965x_set_brightness(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_CONTRAST:
> +		ret = ov965x_set_contrast(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_EXPOSURE_AUTO:
> +		ret = ov965x_set_exposure(ov965x, ctrl->val, false);
> +		break;
> +
> +	case V4L2_CID_AUTOGAIN:
> +		ret = ov965x_set_gain(ov965x, ctrl->val, false);
> +		break;
> +
> +	case V4L2_CID_HFLIP:
> +		ret = ov965x_set_flip(ov965x);
> +		break;
> +
> +	case V4L2_CID_POWER_LINE_FREQUENCY:
> +		ret = ov965x_set_banding_filter(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_SATURATION:
> +		ret = ov965x_set_saturation(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_SHARPNESS:
> +		ret = ov965x_set_sharpness(ov965x, ctrl->val);
> +		break;
> +
> +	case V4L2_CID_TEST_PATTERN:
> +		ret = ov965x_set_test_pattern(ov965x, ctrl->val);
> +		break;
> +	}
> +
> +	mutex_unlock(&ov965x->lock);
> +	return ret;
> +}
> +
> +static const struct v4l2_ctrl_ops ov965x_ctrl_ops = {
> +	.g_volatile_ctrl = ov965x_g_volatile_ctrl,
> +	.s_ctrl	= ov965x_s_ctrl,
> +};
> +
> +static int ov965x_log_status(struct v4l2_subdev *sd)
> +{
> +	v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name);
> +	return 0;
> +}
> +
> +/*
> + * Gain celing - maximum gain values: x2, x4, x8, x16, x32, x64, x128. */
> +#define GAIN_CEILING_MAX 6
> +static const s64 gain_ceiling_menu[GAIN_CEILING_MAX + 1] = {
> +	/* COM9[6:4] = 0...6 */
> +	2 * 16, 4 * 16, 8 * 16, 16 * 16, 32 * 16, 64 * 16, 128 * 16
> +};
> +
> +static const char * const ae_ref_area_menu[] = {
> +	"Full Frame",
> +	"Center Half Frame",
> +	"Center Quarter Frame",
> +	NULL
> +};
> +
> +/* Private control definitions */
> +static const struct v4l2_ctrl_config ov965x_ctrls[] = {
> +	{
> +		.ops = &ov965x_ctrl_ops,
> +		.id = V4L2_CID_GAIN_CEILING,
> +		.type = V4L2_CTRL_TYPE_INTEGER_MENU,
> +		.qmenu_int = gain_ceiling_menu,
> +		.name = "Gain Ceiling",
> +		.max = ARRAY_SIZE(gain_ceiling_menu) - 1,
> +		.def = 2,
> +	}, {
> +		.ops = &ov965x_ctrl_ops,
> +		.id = V4L2_CID_EXPOSURE_REFERENCE_AREA,
> +		.type = V4L2_CTRL_TYPE_MENU,
> +		.qmenu = ae_ref_area_menu,
> +		.name = "Exposure Reference Area",
> +		.max = ARRAY_SIZE(ae_ref_area_menu) - 1,
> +		.def = 1,
> +	},
> +};
> +
> +static const char * const test_pattern_menu[] = {
> +	"Disabled",
> +	"Color bars",
> +	NULL
> +};
> +
> +static int ov965x_initialize_controls(struct ov965x *ov965x)
> +{
> +	const struct v4l2_ctrl_ops *ops = &ov965x_ctrl_ops;
> +	struct ov965x_ctrls *ctrls = &ov965x->ctrls;
> +	struct v4l2_ctrl_handler *hdl = &ctrls->handler;
> +	int ret;
> +
> +	ret = v4l2_ctrl_handler_init(hdl, 13);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Auto/manual white balance */
> +	ctrls->auto_wb = v4l2_ctrl_new_std(hdl, ops,
> +				V4L2_CID_AUTO_WHITE_BALANCE,
> +				0, 1, 1, 1);
> +	ctrls->blue_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BLUE_BALANCE,
> +						0, 0xff, 1, 0x80);
> +	ctrls->red_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_RED_BALANCE,
> +						0, 0xff, 1, 0x80);
> +	/* Auto/manual exposure */
> +	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
> +				V4L2_CID_EXPOSURE_AUTO,
> +				V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO);
> +	/* Exposure time, in 100 us units. min/max is updated dynamically. */
> +	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops,
> +				V4L2_CID_EXPOSURE_ABSOLUTE,
> +				2, 1500, 1, 500);
> +	/* Auto exposure reference frame area */
> +	ctrls->ae_frame_area = v4l2_ctrl_new_custom(hdl,
> +						&ov965x_ctrls[1], NULL);
> +	/* Auto/manual gain */
> +	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
> +						0, 1, 1, 1);
> +	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
> +						16, 64 * (16 + 15), 1, 64 * 16);
> +	ctrls->gain_ceiling = v4l2_ctrl_new_custom(hdl, &ov965x_ctrls[0], NULL);
> +
> +	ctrls->saturation = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION,
> +						-2, 2, 1, 0);
> +	ctrls->brightness = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS,
> +						-3, 3, 1, 0);
> +	ctrls->contrast = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST,
> +						-2, 2, 1, 0);
> +	ctrls->sharpness = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS,
> +						0, 32, 1, 6);
> +
> +	ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0);
> +	ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0);
> +
> +	ctrls->light_freq = v4l2_ctrl_new_std_menu(hdl, ops,
> +				V4L2_CID_POWER_LINE_FREQUENCY,
> +				V4L2_CID_POWER_LINE_FREQUENCY_60HZ, ~0x7,
> +				V4L2_CID_POWER_LINE_FREQUENCY_50HZ);
> +
> +	v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN,
> +				ARRAY_SIZE(test_pattern_menu) - 1, 0, 0,
> +				test_pattern_menu);
> +	if (hdl->error) {
> +		ret = hdl->error;
> +		v4l2_ctrl_handler_free(hdl);
> +		return ret;
> +	}
> +
> +	ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
> +	ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
> +
> +	v4l2_ctrl_auto_cluster(3, &ctrls->auto_wb, 0, false);
> +	v4l2_ctrl_cluster(3, &ctrls->auto_exp);
> +	v4l2_ctrl_cluster(2, &ctrls->hflip);
> +	v4l2_ctrl_cluster(3, &ctrls->auto_gain);

Why don't you use auto_cluster for gain and exposure? It should simplify your
code quite a bit.

I also would expect to see a call to v4l2_ctrl_handler_setup() somewhere to
initialize the hardware. Not strictly necessary if the initial hardware state
is the same as that of the initial controls.

> +
> +	ov965x->sd.ctrl_handler = hdl;
> +	return 0;
> +}
> +
> +/*
> + * V4L2 subdev video and pad level operations
> + */
> +static void ov965x_get_default_format(struct v4l2_mbus_framefmt *mf)
> +{
> +	mf->width = ov965x_framesizes[0].width;
> +	mf->height = ov965x_framesizes[0].height;
> +	mf->colorspace = ov965x_formats[0].colorspace;
> +	mf->code = ov965x_formats[0].code;
> +	mf->field = V4L2_FIELD_NONE;
> +}
> +
> +static int ov965x_enum_mbus_code(struct v4l2_subdev *sd,
> +				 struct v4l2_subdev_fh *fh,
> +				 struct v4l2_subdev_mbus_code_enum *code)
> +{
> +	if (code->index >= ARRAY_SIZE(ov965x_formats))
> +		return -EINVAL;
> +
> +	code->code = ov965x_formats[code->index].code;
> +	return 0;
> +}
> +
> +static int ov965x_enum_frame_sizes(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_fh *fh,
> +				   struct v4l2_subdev_frame_size_enum *fse)
> +{
> +	int i = ARRAY_SIZE(ov965x_formats);
> +
> +	if (fse->index > ARRAY_SIZE(ov965x_framesizes))
> +		return -EINVAL;
> +
> +	while (--i)
> +		if (fse->code == ov965x_formats[i].code)
> +			break;
> +
> +	fse->code = ov965x_formats[i].code;
> +
> +	fse->min_width  = ov965x_framesizes[fse->index].width;
> +	fse->max_width  = fse->min_width;
> +	fse->max_height = ov965x_framesizes[fse->index].height;
> +	fse->min_height = fse->max_height;
> +
> +	return 0;
> +}
> +
> +static int ov965x_g_frame_interval(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_frame_interval *fi)
> +{
> +	struct ov965x *ov965x = to_ov965x(sd);
> +
> +	mutex_lock(&ov965x->lock);
> +	fi->interval = ov965x->fiv->interval;
> +	mutex_unlock(&ov965x->lock);
> +
> +	return 0;
> +}
> +
> +static int __ov965x_set_frame_interval(struct ov965x *ov965x,
> +				       struct v4l2_subdev_frame_interval *fi)
> +{
> +	struct v4l2_mbus_framefmt *mbus_fmt = &ov965x->format;
> +	const struct ov965x_interval *fiv = &ov965x_intervals[0];
> +	u64 req_int, err, min_err = ~0ULL;
> +	unsigned int i;
> +
> +
> +	if (fi->interval.denominator == 0)
> +		return -EINVAL;
> +
> +	req_int = (u64)(fi->interval.numerator * 10000) /
> +		fi->interval.denominator;
> +
> +	for (i = 0; i < ARRAY_SIZE(ov965x_intervals); i++) {
> +		const struct ov965x_interval *iv = &ov965x_intervals[i];
> +
> +		if (mbus_fmt->width != iv->size.width ||
> +		    mbus_fmt->height != iv->size.height)
> +			continue;
> +		err = abs64((u64)(iv->interval.numerator * 10000) /
> +			    iv->interval.denominator - req_int);
> +		if (err < min_err) {
> +			fiv = iv;
> +			min_err = err;
> +		}
> +	}
> +	ov965x->fiv = fiv;
> +
> +	v4l2_dbg(1, debug, &ov965x->sd, "Changed frame interval to %u us\n",
> +		 fiv->interval.numerator * 1000000 / fiv->interval.denominator);
> +
> +	return 0;
> +}
> +
> +static int ov965x_s_frame_interval(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_frame_interval *fi)
> +{
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	int ret;
> +
> +	v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n",
> +		 fi->interval.numerator, fi->interval.denominator);
> +
> +	mutex_lock(&ov965x->lock);
> +	ret = __ov965x_set_frame_interval(ov965x, fi);
> +	ov965x->apply_frame_fmt = 1;
> +	mutex_unlock(&ov965x->lock);
> +	return ret;
> +}
> +
> +static int ov965x_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
> +			  struct v4l2_subdev_format *fmt)
> +{
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	struct v4l2_mbus_framefmt *mf;
> +
> +	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> +		mf = v4l2_subdev_get_try_format(fh, 0);
> +		fmt->format = *mf;
> +		return 0;
> +	}
> +
> +	mutex_lock(&ov965x->lock);
> +	fmt->format = ov965x->format;
> +	mutex_unlock(&ov965x->lock);
> +
> +	return 0;
> +}
> +
> +static void __ov965x_try_frame_size(struct v4l2_mbus_framefmt *mf,
> +				    const struct ov965x_framesize **size)
> +{
> +	const struct ov965x_framesize *fsize = &ov965x_framesizes[0],
> +		*match = NULL;
> +	int i = ARRAY_SIZE(ov965x_framesizes);
> +	unsigned int min_err = UINT_MAX;
> +
> +	while (i--) {
> +		int err = abs(fsize->width - mf->width)
> +				+ abs(fsize->height - mf->height);
> +		if (err < min_err) {
> +			min_err = err;
> +			match = fsize;
> +		}
> +		fsize++;
> +	}
> +	if (!match)
> +		match = &ov965x_framesizes[0];
> +	mf->width  = match->width;
> +	mf->height = match->height;
> +	if (size)
> +		*size = match;
> +}
> +
> +static int ov965x_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
> +			  struct v4l2_subdev_format *fmt)
> +{
> +	unsigned int index = ARRAY_SIZE(ov965x_formats);
> +	struct v4l2_mbus_framefmt *mf = &fmt->format;
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	const struct ov965x_framesize *size = NULL;
> +	int ret = 0;
> +
> +	__ov965x_try_frame_size(mf, &size);
> +
> +	while (--index)
> +		if (ov965x_formats[index].code == mf->code)
> +			break;
> +
> +	mf->colorspace	= V4L2_COLORSPACE_JPEG;
> +	mf->code	= ov965x_formats[index].code;
> +	mf->field	= V4L2_FIELD_NONE;
> +
> +	mutex_lock(&ov965x->lock);
> +
> +	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> +		if (fh != NULL) {
> +			mf = v4l2_subdev_get_try_format(fh, fmt->pad);
> +			*mf = fmt->format;
> +		}
> +	} else {
> +		if (ov965x->streaming) {
> +			ret = -EBUSY;
> +		} else {
> +			ov965x->frame_size = size;
> +			ov965x->format = fmt->format;
> +			ov965x->tslb_reg = ov965x_formats[index].tslb_reg;
> +			ov965x->apply_frame_fmt = 1;
> +		}
> +	}
> +
> +	if (!ret && fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
> +		struct v4l2_subdev_frame_interval fiv = {
> +			.interval = {0, 1}
> +		};
> +		/* Reset to minimum possible frame interval */
> +		__ov965x_set_frame_interval(ov965x, &fiv);
> +	}
> +	mutex_unlock(&ov965x->lock);
> +
> +	if (!ret)
> +		ov965x_update_exposure_ctrl(ov965x);
> +
> +	return ret;
> +}
> +
> +static int ov965x_set_frame_size(struct ov965x *ov965x)
> +{
> +	int i, ret = 0;
> +
> +	for (i = 0; ret == 0 && i < NUM_FMT_REGS; i++)
> +		ret = ov965x_write(ov965x->client, frame_size_reg_addr[i],
> +				   ov965x->frame_size->regs[i]);
> +	return ret;
> +}
> +
> +static int __ov965x_set_params(struct ov965x *ov965x)
> +{
> +	struct i2c_client *client = ov965x->client;
> +	struct ov965x_ctrls *ctrls = &ov965x->ctrls;
> +	int ret = 0;
> +	u8 reg;
> +
> +	if (ov965x->apply_frame_fmt) {
> +		reg = DEF_CLKRC + ov965x->fiv->clkrc_div;
> +		ret = ov965x_write(client, REG_CLKRC, reg);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov965x_set_frame_size(ov965x);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov965x_read(client, REG_TSLB, &reg);
> +		if (ret < 0)
> +			return ret;
> +		reg &= ~TSLB_YUYV_MASK;
> +		reg |= ov965x->tslb_reg;
> +		ret = ov965x_write(client, REG_TSLB, reg);
> +		if (ret < 0)
> +			return ret;
> +	}
> +	ret = ov965x_set_default_gamma_curve(ov965x);
> +	if (ret < 0)
> +		return ret;
> +	ret = ov965x_set_color_matrix(ov965x);
> +	if (ret < 0)
> +		return ret;
> +	/*
> +	 * Select manual banding filter, the filter will
> +	 * be enabled further if required.
> +	 */
> +	ret = ov965x_read(client, REG_COM11, &reg);
> +	if (!ret)
> +		reg |= COM11_BANDING;
> +	ret = ov965x_write(client, REG_COM11, reg);
> +	if (ret < 0)
> +		return ret;
> +
> +	if (ctrls->update) {
> +		ret = __ov965x_restore_controls(ov965x);
> +		if (ret < 0)
> +			return ret;
> +		ctrls->update = 0;
> +	}
> +	/*
> +	 * Banding filter (REG_MBD value) needs to match selected
> +	 * resolution and frame rate, so it's always updated here.
> +	 */
> +	return ov965x_set_banding_filter(ov965x, ctrls->light_freq->val);
> +}
> +
> +static int ov965x_s_stream(struct v4l2_subdev *sd, int on)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(sd);
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	int ret = 0;
> +
> +	v4l2_dbg(1, debug, client, "%s: on: %d\n", __func__, on);
> +
> +	mutex_lock(&ov965x->lock);
> +	if (ov965x->streaming == !on) {
> +		if (on)
> +			ret = __ov965x_set_params(ov965x);
> +		if (!ret)
> +			ret = ov965x_write(client, REG_COM2,
> +					   on ? 0x01 : 0x11);
> +	}
> +	if (!ret)
> +		ov965x->streaming += on ? 1 : -1;
> +
> +	WARN_ON(ov965x->streaming < 0);
> +	mutex_unlock(&ov965x->lock);
> +
> +	return ret;
> +}
> +
> +/*
> + * V4L2 subdev internal operations
> + */
> +static int ov965x_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> +	struct v4l2_mbus_framefmt *mf = v4l2_subdev_get_try_format(fh, 0);
> +
> +	ov965x_get_default_format(mf);
> +	v4l2_info(sd, "%s:%d\n", __func__, __LINE__);

Shouldn't v4l2_dbg be better? Or don't print anything. Normal usage of a driver
should produce output to the kernel log.

> +	return 0;
> +}
> +
> +static const struct v4l2_subdev_pad_ops ov965x_pad_ops = {
> +	.enum_mbus_code = ov965x_enum_mbus_code,
> +	.enum_frame_size = ov965x_enum_frame_sizes,
> +	.get_fmt = ov965x_get_fmt,
> +	.set_fmt = ov965x_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_video_ops ov965x_video_ops = {
> +	.s_stream = ov965x_s_stream,
> +	.g_frame_interval = ov965x_g_frame_interval,
> +	.s_frame_interval = ov965x_s_frame_interval,
> +
> +};
> +
> +static const struct v4l2_subdev_internal_ops ov965x_sd_internal_ops = {
> +	.open = ov965x_open,
> +};
> +
> +static const struct v4l2_subdev_core_ops ov965x_core_ops = {
> +	.s_power = ov965x_s_power,
> +	.log_status = ov965x_log_status,
> +};
> +
> +static const struct v4l2_subdev_ops ov965x_subdev_ops = {
> +	.core = &ov965x_core_ops,
> +	.pad = &ov965x_pad_ops,
> +	.video = &ov965x_video_ops,
> +};
> +
> +/*
> + * Reset and power down GPIOs configuration
> + */
> +static int ov965x_configure_gpios(struct ov965x *ov965x,
> +				  const struct ov9650_platform_data *pdata)
> +{
> +	int ret, i;
> +
> +	ov965x->gpios[GPIO_PWDN] = pdata->gpio_pwdn;
> +	ov965x->gpios[GPIO_RST]  = pdata->gpio_reset;
> +
> +	for (i = 0; i < ARRAY_SIZE(ov965x->gpios); i++) {
> +		int gpio = ov965x->gpios[i];
> +
> +		if (!gpio_is_valid(gpio))
> +			continue;
> +		ret = devm_gpio_request_one(&ov965x->client->dev, gpio,
> +					    GPIOF_OUT_INIT_HIGH, "OV965X");
> +		if (ret < 0)
> +			return ret;
> +		v4l2_dbg(1, debug, &ov965x->sd, "set gpio %d to 1\n", gpio);
> +
> +		gpio_set_value(gpio, 1);
> +		gpio_export(gpio, 0);
> +		ov965x->gpios[i] = gpio;
> +	}
> +
> +	return 0;
> +}
> +
> +static int ov965x_detect_sensor(struct v4l2_subdev *sd)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(sd);
> +	struct ov965x *ov965x = to_ov965x(sd);
> +	u8 pid, ver;
> +	int ret;
> +
> +	mutex_lock(&ov965x->lock);
> +	 __ov965x_set_power(ov965x, 1);
> +	usleep_range(25000, 26000);
> +
> +	/* Check sensor revision */
> +	ret = ov965x_read(client, REG_PID, &pid);
> +	if (!ret)
> +		ret = ov965x_read(client, REG_VER, &ver);
> +
> +	if (!ret) {
> +		ov965x->id = OV965X_ID(pid, ver);
> +		if (ov965x->id == OV9650_ID || ov965x->id == OV9650_ID)
> +			v4l2_info(sd, "Found OV%04X sensor\n", ov965x->id);
> +		else
> +			v4l2_err(sd, "Sensor detection failed (%04X, %d)\n",
> +				 ov965x->id, ret);
> +	}
> +	__ov965x_set_power(ov965x, 0);
> +
> +	mutex_unlock(&ov965x->lock);
> +	return ret;
> +}
> +
> +static int ov965x_probe(struct i2c_client *client,
> +			const struct i2c_device_id *id)
> +{
> +	const struct ov9650_platform_data *pdata = client->dev.platform_data;
> +	struct v4l2_subdev *sd;
> +	struct ov965x *ov965x;
> +	int ret;
> +
> +	if (pdata == NULL) {
> +		dev_err(&client->dev, "platform data not specified\n");
> +		return -EINVAL;
> +	}
> +
> +	if (pdata->mclk_frequency == 0) {
> +		dev_err(&client->dev, "MCLK frequency not specified\n");
> +		return -EINVAL;
> +	}
> +
> +	ov965x = devm_kzalloc(&client->dev, sizeof(*ov965x), GFP_KERNEL);
> +	if (!ov965x)
> +		return -ENOMEM;
> +
> +	mutex_init(&ov965x->lock);
> +	ov965x->client = client;
> +	ov965x->mclk_frequency = pdata->mclk_frequency;
> +
> +	sd = &ov965x->sd;
> +	v4l2_i2c_subdev_init(sd, client, &ov965x_subdev_ops);
> +	strlcpy(sd->name, DRIVER_NAME, sizeof(sd->name));
> +
> +	sd->internal_ops = &ov965x_sd_internal_ops;
> +	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +
> +	ret = ov965x_configure_gpios(ov965x, pdata);
> +	if (ret < 0)
> +		return ret;
> +
> +	ov965x->pad.flags = MEDIA_PAD_FL_SOURCE;
> +	sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR;
> +	ret = media_entity_init(&sd->entity, 1, &ov965x->pad, 0);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = ov965x_initialize_controls(ov965x);
> +	if (ret < 0)
> +		goto err_me;
> +
> +	ov965x_get_default_format(&ov965x->format);
> +	ov965x->frame_size = &ov965x_framesizes[0];
> +	ov965x->fiv = &ov965x_intervals[0];
> +
> +	ret = ov965x_detect_sensor(sd);
> +	if (ret < 0)
> +		goto err_ctrls;
> +
> +	/* Update exposure time min/max to match frame format */
> +	ov965x_update_exposure_ctrl(ov965x);
> +
> +	return 0;
> +err_ctrls:
> +	v4l2_ctrl_handler_free(sd->ctrl_handler);
> +err_me:
> +	media_entity_cleanup(&sd->entity);
> +	return ret;
> +}
> +
> +static int ov965x_remove(struct i2c_client *client)
> +{
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +
> +	v4l2_device_unregister_subdev(sd);
> +	v4l2_ctrl_handler_free(sd->ctrl_handler);
> +	media_entity_cleanup(&sd->entity);
> +
> +	return 0;
> +}
> +
> +static const struct i2c_device_id ov965x_id[] = {
> +	{ "OV9650", 0 },
> +	{ "OV9652", 0 },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(i2c, ov965x_id);
> +
> +static struct i2c_driver ov965x_i2c_driver = {
> +	.driver = {
> +		.name	= DRIVER_NAME,
> +	},
> +	.probe		= ov965x_probe,
> +	.remove		= ov965x_remove,
> +	.id_table	= ov965x_id,
> +};
> +
> +module_i2c_driver(ov965x_i2c_driver);
> +
> +MODULE_AUTHOR("Sylwester Nawrocki <sylvester.nawrocki@xxxxxxxxx>");
> +MODULE_DESCRIPTION("OV9650/OV9652 CMOS Image Sensor driver");
> +MODULE_LICENSE("GPL");
> diff --git a/include/media/ov9650.h b/include/media/ov9650.h
> new file mode 100644
> index 0000000..ba548a4
> --- /dev/null
> +++ b/include/media/ov9650.h
> @@ -0,0 +1,20 @@
> +/*
> + * OV9650/OV9652 camera sensors driver
> + *
> + * Copyright (C) 2012 Sylwester Nawrocki <sylvester.nawrocki@xxxxxxxxx>

2012 -> 2013 :-)

> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef OV9650_H_
> +#define OV9650_H_
> +
> +struct ov9650_platform_data {
> +	unsigned long mclk_frequency;
> +	int gpio_pwdn;
> +	int gpio_reset;

Some comments for these fields would be welcome.

> +};
> +
> +#endif /* OV9650_H_ */
> 

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux