Am 04.12.2012 03:58, schrieb Devin Heitmueller:
> On Mon, Dec 3, 2012 at 9:42 PM, Matthew Gyurgyik <matthew@xxxxxxxxxx> wrote:
>>> I would try running "lsusb -v" and send the output. Make sure that
>>> it's not expecting to use bulk mode for DVB (which would require
>>> driver changes to support).
>>>
>>> Devin
>>>
>> Here is the output of lsusb -v
>> http://pyther.net/a/digivox_atsc/patch2/lsusb.txt
> Hmmm, it's isoc, so that should be ok. Maybe the 3305 TS
> configuration is mismatched (serial vs. parallel). I don't recall off
> the top of my head, but I think em2875 is pretty much always in serial
> mode, so check the lgdt3305 config block passed in the dvb_attach()
> call and see if it's the same.
I double-checked the log and it is indeed set to LGDT3305_MPEG_SERIAL,
but LGDT3305_TPCLK_FALLING_EDGE is used instead of
LGDT3305_TPCLK_RISING_EDGE.
OTOH, the KWorld A340 bord sets this to LGDT3305_MPEG_PARALLEL...
Matthew, could you please test V3 of the patch ? It is written against
the media_tree staging/for_v3.8 (see http://git.linuxtv.org/media_tree.git).
You could also already test the remote control key map (e.g. with evtest)
Regards,
Frank
>
> Devin
>
>From 7f7aa989a339f9510db53662042c39551b40b0df Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Frank=20Sch=C3=A4fer?= <fschaefer.oss@xxxxxxxxxxxxxx>
Date: Tue, 4 Dec 2012 22:03:47 +0100
Subject: [PATCH] Experimental patch for the 'MSI DIGIVOX ATSC' V3
---
drivers/media/usb/em28xx/em28xx-cards.c | 30 ++++++++++++++++++++++++
drivers/media/usb/em28xx/em28xx-dvb.c | 38 +++++++++++++++++++++++++++++++
drivers/media/usb/em28xx/em28xx.h | 1 +
3 Dateien geändert, 69 Zeilen hinzugefügt(+)
diff --git a/drivers/media/usb/em28xx/em28xx-cards.c b/drivers/media/usb/em28xx/em28xx-cards.c
index 619bffb..ec3b29b 100644
--- a/drivers/media/usb/em28xx/em28xx-cards.c
+++ b/drivers/media/usb/em28xx/em28xx-cards.c
@@ -393,6 +393,21 @@ static struct em28xx_reg_seq pctv_520e[] = {
{ -1, -1, -1, -1},
};
+/* 0db0:8810 MSI DIGIVOX ATSC (HU345-Q)
+ * GPIO_0 - ??? (related to eeprom reading ?)
+ * GPIO_6 - ??? (TDA18271C2 or/and LGDT3305 reset ?)
+ * GPIO_7 - ??? (wakeup or stream enable ?)
+ */
+static struct em28xx_reg_seq msi_digivox_atsc[] = {
+ {EM2874_R80_GPIO, 0xff, 0xff, 50}, /* GPIO_0=1 */
+ {0x0d, 0xff, 0xff, 0},
+ {EM2874_R80_GPIO, 0xfe, 0xff, 0}, /* GPIO_0=0 */
+ {EM2874_R80_GPIO, 0xbe, 0xff, 135}, /* GPIO_6=0 */
+ {EM2874_R80_GPIO, 0xfe, 0xff, 135}, /* GPIO_6=1 */
+ {EM2874_R80_GPIO, 0x7e, 0xff, 20}, /* GPIO_7=0 */
+ { -1, -1, -1, -1},
+};
+
/*
* Board definitions
*/
@@ -1988,6 +2003,19 @@ struct em28xx_board em28xx_boards[] = {
EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
+ /* 0db0:8810 MSI DIGIVOX ATSC (HU345-Q)
+ * Empia EM2874B + TDA18271HDC2 + LGDT3305 */
+ [EM2874_BOARD_MSI_DIGIVOX_ATSC] = {
+ .name = "MSI DIGIVOX ATSC",
+ .dvb_gpio = msi_digivox_atsc,
+ .has_dvb = 1,
+ .tuner_type = TUNER_ABSENT,
+ .ir_codes = RC_MAP_MSI_DIGIVOX_III, /* just a guess from looking at the picture */
+ .xclk = EM28XX_XCLK_FREQUENCY_12MHZ, /* TODO */
+ .i2c_speed = EM2874_I2C_SECONDARY_BUS_SELECT |
+ EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_100_KHZ,
+ },
};
const unsigned int em28xx_bcount = ARRAY_SIZE(em28xx_boards);
@@ -2145,6 +2173,8 @@ struct usb_device_id em28xx_id_table[] = {
.driver_info = EM2884_BOARD_PCTV_510E },
{ USB_DEVICE(0x2013, 0x0251),
.driver_info = EM2884_BOARD_PCTV_520E },
+ { USB_DEVICE(0x0db0, 0x8810),
+ .driver_info = EM2874_BOARD_MSI_DIGIVOX_ATSC },
{ },
};
MODULE_DEVICE_TABLE(usb, em28xx_id_table);
diff --git a/drivers/media/usb/em28xx/em28xx-dvb.c b/drivers/media/usb/em28xx/em28xx-dvb.c
index 63f2e70..b4855c8 100644
--- a/drivers/media/usb/em28xx/em28xx-dvb.c
+++ b/drivers/media/usb/em28xx/em28xx-dvb.c
@@ -263,6 +263,18 @@ static struct lgdt3305_config em2870_lgdt3304_dev = {
.qam_if_khz = 4000,
};
+static struct lgdt3305_config em2874_lgdt3305_dev = {
+ .i2c_addr = 0x0e,
+ .demod_chip = LGDT3305,
+ .spectral_inversion = 1,
+ .rf_agc_loop = 0,
+ .mpeg_mode = LGDT3305_MPEG_PARALLEL,
+ .tpclk_edge = LGDT3305_TPCLK_FALLING_EDGE,
+ .tpvalid_polarity = LGDT3305_TP_VALID_HIGH,
+ .vsb_if_khz = 3250, /* not confirmed with a USB log */
+ .qam_if_khz = 4000,
+};
+
static struct s921_config sharp_isdbt = {
.demod_address = 0x30 >> 1
};
@@ -713,6 +725,14 @@ static struct tda18271_config em28xx_cxd2820r_tda18271_config = {
.gate = TDA18271_GATE_DIGITAL,
};
+static struct tda18271_config em28xx_lgdt3305_tda18271_config = {
+ .std_map = &kworld_a340_std_map, /* TODO / EXPERIMENTAL */
+ .gate = TDA18271_GATE_DIGITAL,
+ .output_opt = TDA18271_OUTPUT_LT_OFF,
+/* .rf_cal_on_startup = 1, */ /* needed ??? */
+/* .delay_cal = 1, */ /* needed ??? */
+};
+
static const struct tda10071_config em28xx_tda10071_config = {
.i2c_address = 0x55, /* (0xaa >> 1) */
.i2c_wr_max = 64,
@@ -1235,6 +1255,24 @@ static int em28xx_dvb_init(struct em28xx *dev)
goto out_free;
}
break;
+ case EM2874_BOARD_MSI_DIGIVOX_ATSC:
+ dvb->fe[0] = dvb_attach(lgdt3305_attach,
+ &em2874_lgdt3305_dev,
+ &dev->i2c_adap);
+ if (dvb->fe[0]) {
+ /* FE 0 attach tuner */
+ if (!dvb_attach(tda18271_attach,
+ dvb->fe[0],
+ 0x60,
+ &dev->i2c_adap,
+ &em28xx_lgdt3305_tda18271_config)) {
+
+ dvb_frontend_detach(dvb->fe[0]);
+ result = -EINVAL;
+ goto out_free;
+ }
+ }
+ break;
default:
em28xx_errdev("/2: The frontend of your DVB/ATSC card"
" isn't supported yet\n");
diff --git a/drivers/media/usb/em28xx/em28xx.h b/drivers/media/usb/em28xx/em28xx.h
index 86e90d8..3102ff3 100644
--- a/drivers/media/usb/em28xx/em28xx.h
+++ b/drivers/media/usb/em28xx/em28xx.h
@@ -129,6 +129,7 @@
#define EM2884_BOARD_PCTV_510E 85
#define EM2884_BOARD_PCTV_520E 86
#define EM2884_BOARD_TERRATEC_HTC_USB_XS 87
+#define EM2874_BOARD_MSI_DIGIVOX_ATSC 88
/* Limits minimum and default number of buffers */
#define EM28XX_MIN_BUF 4
--
1.7.10.4
