On Mon, Oct 15, 2012 at 01:01:11PM +0200, Matthijs Kooijman wrote: > Hey Folks, > > > I've been suffering from a NULL pointer crash while initializing the > > nuvoton_cir driver. It occurs 100% reliable on a 3.5 kernel when I > > bombard my receiver with IR signals during bootup. > > > > It seems that 9ef449c: [media] rc: Postpone ISR registration attempts to > > fix this very issue, but does not fix it completely. > > I've looked a bit more closely at the code and I do not really > understand why this commit actually fixed the crash for some (ite-cir) > users. Looking at the bugreport linked to in that commit [1], users > report their bug is fixed, but I don't really understand why. Perhaps > the window for this race condition is just made smaller, but not > entirely eliminated? Your diagnosis seem to be correct and I have already tried to address this: https://lkml.org/lkml/2012/8/25/84 There's also a bug reported here: https://bugzilla.kernel.org/attachment.cgi?id=78491 I've submitted a patch to try to fix it but got no comments yet. My patch moves the request_irq() invocation further down the initialisation code, after the rc_register_device() (which I believe is the correct thing to do). > > Note that the actual patch tested by the Launchpad users (which is > included in the Ubuntu kernel) is a smaller patch than the one in > git, but the essence is still the same. Again, this is correct. The patch tested was just for a subset of the drivers and this fix was later ported to the other affected drivers. But again, as you referred above, this doesn't completely fix the issue as it just reduced the race window. Cheers, -- Luis > > [1]: http://bugs.launchpad.net/bugs/972723 > > > In particular, I'm not sure if it's ok to start firing IRQ's before > > rc_register_device is called. rc_register_device also calls > > ir_raw_event_register to init rdev->raw, which is again used by > > ir_raw_event_store_with_filter. > It seems this particular thing did not cause a (reproducible) problem, > since ir_raw_event_store_with_filter bails out when rdev->raw is NULL > (returning -EINVAL, but that's ignored by nvt_process_rx_ir_data). > > Still, since there is still a small time window in which rdev->raw is > not NULL, but not completely initialized either, I believe that the irqs > should not be registered until after rc_register_device was called. > > > I've also looked at the USB IR drivers and it seems some potentially > have the same problem. In particular, usb_fill_int_urb (for iguanair and > ati-remote) or redrat3_enable_detector (for redrat3) is called before > rc_register_device and other initialization, but I don't know the USB > subsystem well enough to know if this is really a problem or if simply > moving th usb_fill_int_urb / redrat3_enable_detector would help at all. > > The mceusb, streamzap and gpio-ir-recv drivers look like they initialize the interrupt > usb at the end and shouldn't suffer from this problem. > > > I'll send a patch series for this bug in a minute. It also fixes some > problem in cleanup of ene-ir I noticed while reading the code and > renames some of the cleanup labels (which should make the last patch > easier to review). I've tried to separate changes as much as possible, > if there's anything you'd like to see different, just let me know. > > Since I only have nuvoton-cir hardware, the changes to the other drivers > are compile-tested only (but the drivers are similar enough that I > expect no problems there). > > Gr. > > Matthijs -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
