On 10/03/2012 10:13 AM, Oliver Endriss wrote:
Mauro Carvalho Chehab <mchehab@xxxxxxxxxx> wrote:
Due to udev-182, the firmware load was changed to be async, as
otherwise udev would give up of loading a firmware.
Add an option to return to the previous behaviour, async firmware
loads cause failures with the tda18271 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
---
drivers/media/dvb-frontends/drxk.h | 2 ++
drivers/media/dvb-frontends/drxk_hard.c | 20 +++++++++++++++-----
2 files changed, 17 insertions(+), 5 deletions(-)
diff --git a/drivers/media/dvb-frontends/drxk.h b/drivers/media/dvb-frontends/drxk.h
index d615d7d..94fecfb 100644
--- a/drivers/media/dvb-frontends/drxk.h
+++ b/drivers/media/dvb-frontends/drxk.h
@@ -28,6 +28,7 @@
* A value of 0 (default) or lower indicates that
* the correct number of parameters will be
* automatically detected.
+ * @load_firmware_sync: Force the firmware load to be synchronous.
*
* On the *_gpio vars, bit 0 is UIO-1, bit 1 is UIO-2 and bit 2 is
* UIO-3.
@@ -39,6 +40,7 @@ struct drxk_config {
bool parallel_ts;
bool dynamic_clk;
bool enable_merr_cfg;
+ bool load_firmware_sync;
bool antenna_dvbt;
u16 antenna_gpio;
diff --git a/drivers/media/dvb-frontends/drxk_hard.c b/drivers/media/dvb-frontends/drxk_hard.c
index 1ab8154..8b4c6d5 100644
--- a/drivers/media/dvb-frontends/drxk_hard.c
+++ b/drivers/media/dvb-frontends/drxk_hard.c
@@ -6609,15 +6609,25 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
/* Load firmware and initialize DRX-K */
if (state->microcode_name) {
- status = request_firmware_nowait(THIS_MODULE, 1,
+ if (config->load_firmware_sync) {
+ const struct firmware *fw = NULL;
+
+ status = request_firmware(&fw, state->microcode_name,
+ state->i2c->dev.parent);
+ if (status < 0)
+ fw = NULL;
+ load_firmware_cb(fw, state);
+ } else {
+ status = request_firmware_nowait(THIS_MODULE, 1,
state->microcode_name,
state->i2c->dev.parent,
GFP_KERNEL,
state, load_firmware_cb);
- if (status < 0) {
- printk(KERN_ERR
- "drxk: failed to request a firmware\n");
- return NULL;
+ if (status < 0) {
+ printk(KERN_ERR
+ "drxk: failed to request a firmware\n");
+ return NULL;
+ }
}
} else if (init_drxk(state) < 0)
goto error;
Sorry. loading the firmware asynchronously is simply crap! Remove this!
If you intend to load a firmware, firmware loading must be the first
thing you do with the drxk. You must not access the device, before
firmware loading has completed, or correct operation will not be
guaranteed.
If you insist to keep this option, I request that you make synchronous
loading the default, and you enable asynchronous loading only for
devices _you_ have tested. I will never use asynchronous loading.
(In fact, I have already backed-out your firmware patches from my
drivers and forked off my own version of the drxk.)
+1, indeed. Broken by design.
That was quite what I explained earlier too. You are not allowed to
continue attach path until previous attach is done and chip is ready to
offer interface(s) to the chips which are next in attach path. It is not
only that, but general rule.
I don't see any reason why this code should be left here.
regards
Antti
--
http://palosaari.fi/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
