On Fri September 21 2012 11:21:37 Federico Vaga wrote:
> This patch re-write the driver and use the videobuf2
> interface instead of the old videobuf. Moreover, it uses also
> the control framework which allows the driver to inherit
> controls from its subdevice (ADV7180)
Some more comments below, nothing major.
> Signed-off-by: Federico Vaga <federico.vaga@xxxxxxxxx>
> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@xxxxxx>
> ---
> drivers/media/pci/sta2x11/Kconfig | 2 +-
> drivers/media/pci/sta2x11/sta2x11_vip.c | 1235 ++++++++++---------------------
> 2 file modificati, 411 inserzioni(+), 826 rimozioni(-)
>
> diff --git a/drivers/media/pci/sta2x11/Kconfig b/drivers/media/pci/sta2x11/Kconfig
> index 6749f67..654339f 100644
> --- a/drivers/media/pci/sta2x11/Kconfig
> +++ b/drivers/media/pci/sta2x11/Kconfig
> @@ -2,7 +2,7 @@ config STA2X11_VIP
> tristate "STA2X11 VIP Video For Linux"
> depends on STA2X11
> select VIDEO_ADV7180 if MEDIA_SUBDRV_AUTOSELECT
> - select VIDEOBUF_DMA_CONTIG
> + select VIDEOBUF2_DMA_STREAMING
> depends on PCI && VIDEO_V4L2 && VIRT_TO_BUS
> help
> Say Y for support for STA2X11 VIP (Video Input Port) capture
> diff --git a/drivers/media/pci/sta2x11/sta2x11_vip.c b/drivers/media/pci/sta2x11/sta2x11_vip.c
> index 4c10205..f423039 100644
> --- a/drivers/media/pci/sta2x11/sta2x11_vip.c
> +++ b/drivers/media/pci/sta2x11/sta2x11_vip.c
> @@ -1,6 +1,7 @@
> /*
> * This is the driver for the STA2x11 Video Input Port.
> *
> + * Copyright (C) 2012 ST Microelectronics
> * Copyright (C) 2010 WindRiver Systems, Inc.
> *
> * This program is free software; you can redistribute it and/or modify it
> @@ -19,36 +20,30 @@
> * The full GNU General Public License is included in this distribution in
> * the file called "COPYING".
> *
> - * Author: Andreas Kies <andreas.kies@xxxxxxxxxxxxx>
> - * Vlad Lungu <vlad.lungu@xxxxxxxxxxxxx>
> - *
> */
>
> #include <linux/types.h>
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/init.h>
> -#include <linux/vmalloc.h>
> -
> #include <linux/videodev2.h>
> -
> #include <linux/kmod.h>
> -
> #include <linux/pci.h>
> #include <linux/interrupt.h>
> -#include <linux/mutex.h>
> #include <linux/io.h>
> #include <linux/gpio.h>
> #include <linux/i2c.h>
> #include <linux/delay.h>
> #include <media/v4l2-common.h>
> #include <media/v4l2-device.h>
> +#include <media/v4l2-ctrls.h>
> #include <media/v4l2-ioctl.h>
> -#include <media/videobuf-dma-contig.h>
> +#include <media/v4l2-fh.h>
> +#include <media/v4l2-event.h>
> +#include <media/videobuf2-dma-streaming.h>
>
> #include "sta2x11_vip.h"
>
> -#define DRV_NAME "sta2x11_vip"
> #define DRV_VERSION "1.3"
>
> #ifndef PCI_DEVICE_ID_STMICRO_VIP
> @@ -63,8 +58,8 @@
> #define DVP_TFS 0x08
> #define DVP_BFO 0x0C
> #define DVP_BFS 0x10
> -#define DVP_VTP 0x14
> -#define DVP_VBP 0x18
> +#define DVP_VTP 0x14
> +#define DVP_VBP 0x18
> #define DVP_VMP 0x1C
> #define DVP_ITM 0x98
> #define DVP_ITS 0x9C
> @@ -84,44 +79,24 @@
>
> #define DVP_HLFLN_SD 0x00000001
>
> -#define REG_WRITE(vip, reg, value) iowrite32((value), (vip->iomem)+(reg))
> -#define REG_READ(vip, reg) ioread32((vip->iomem)+(reg))
> -
> #define SAVE_COUNT 8
> #define AUX_COUNT 3
> #define IRQ_COUNT 1
>
> -/**
> - * struct sta2x11_vip - All internal data for one instance of device
> - * @v4l2_dev: device registered in v4l layer
> - * @video_dev: properties of our device
> - * @pdev: PCI device
> - * @adapter: contains I2C adapter information
> - * @register_save_area: All relevant register are saved here during suspend
> - * @decoder: contains information about video DAC
> - * @format: pixel format, fixed UYVY
> - * @std: video standard (e.g. PAL/NTSC)
> - * @input: input line for video signal ( 0 or 1 )
> - * @users: Number of open of device ( max. 1 )
> - * @disabled: Device is in power down state
> - * @mutex: ensures exclusive opening of device
> - * @slock: for excluse acces of registers
> - * @vb_vidq: queue maintained by videobuf layer
> - * @capture: linked list of capture buffer
> - * @active: struct videobuf_buffer currently beingg filled
> - * @started: device is ready to capture frame
> - * @closing: device will be shut down
> - * @tcount: Number of top frames
> - * @bcount: Number of bottom frames
> - * @overflow: Number of FIFO overflows
> - * @mem_spare: small buffer of unused frame
> - * @dma_spare: dma addres of mem_spare
> - * @iomem: hardware base address
> - * @config: I2C and gpio config from platform
> - *
> - * All non-local data is accessed via this structure.
> - */
>
> +struct vip_buffer {
> + struct vb2_buffer vb;
> + struct list_head list;
> + dma_addr_t dma;
> +};
> +static inline struct vip_buffer *to_vip_buffer(struct vb2_buffer *vb2)
> +{
> + return container_of(vb2, struct vip_buffer, vb);
> +}
> +
> +struct sta2x11_vip_fh {
> + struct v4l2_fh fh;
> +};
No need to make a sta2x11_vip_fh struct, just use v4l2_fh directly. It doesn't
add anything. In fact, it's not even used.
> struct sta2x11_vip {
> struct v4l2_device v4l2_dev;
> struct video_device *video_dev;
> @@ -129,21 +104,27 @@ struct sta2x11_vip {
> struct i2c_adapter *adapter;
> unsigned int register_save_area[IRQ_COUNT + SAVE_COUNT + AUX_COUNT];
> struct v4l2_subdev *decoder;
> - struct v4l2_pix_format format;
> - v4l2_std_id std;
> - unsigned int input;
> - int users;
> - int disabled;
> - struct mutex mutex; /* exclusive access during open */
> - spinlock_t slock; /* spin lock for hardware and queue access */
> - struct videobuf_queue vb_vidq;
> - struct list_head capture;
> - struct videobuf_buffer *active;
> - int started, closing, tcount, bcount;
> + struct v4l2_ctrl_handler ctrl_hdl;
> +
> +
> + struct v4l2_pix_format format; /* pixel format, fixed UYVY */
> + v4l2_std_id std; /* Video standard (PAL/NTSC)*/
> + unsigned int input; /* Input line (0 or 1) */
> + int disabled; /* 1 disabled 0 enabled */
> + spinlock_t slock; /* spin lock for hardware */
> +
> + struct vb2_alloc_ctx *alloc_ctx;
> + struct vb2_queue vb_vidq; /* queue maintaned by videobuf2 */
> + struct list_head buffer_list; /* list of buffers */
> + unsigned int sequence;
> + struct vip_buffer *active; /* current active buffer */
> + spinlock_t lock; /* Used in videobuf2 callback */
> +
> + /* Interrupt counters */
> + int tcount, bcount;
> int overflow;
> - void *mem_spare;
> - dma_addr_t dma_spare;
> - void *iomem;
> +
> + void *iomem; /* I/O Memory */
> struct vip_config *config;
> };
>
> @@ -206,360 +187,217 @@ static struct v4l2_pix_format formats_60[] = {
> .colorspace = V4L2_COLORSPACE_SMPTE170M},
> };
>
> -/**
> - * buf_setup - Get size and number of video buffer
> - * @vq: queue in videobuf
> - * @count: Number of buffers (1..MAX_FRAMES).
> - * 0 use default value.
> - * @size: size of buffer in bytes
> - *
> - * returns size and number of buffers
> - * a preset value of 0 returns the default number.
> - * return value: 0, always succesfull.
> - */
> -static int buf_setup(struct videobuf_queue *vq, unsigned int *count,
> - unsigned int *size)
> +/* Write VIP register */
> +static inline void reg_write(struct sta2x11_vip *vip, unsigned int reg, u32 val)
> {
> - struct sta2x11_vip *vip = vq->priv_data;
> -
> - *size = vip->format.width * vip->format.height * 2;
> - if (0 == *count || MAX_FRAMES < *count)
> - *count = MAX_FRAMES;
> - return 0;
> -};
> -
> -/**
> - * buf_prepare - prepare buffer for usage
> - * @vq: queue in videobuf layer
> - * @vb: buffer to be prepared
> - * @field: type of video data (interlaced/non-interlaced)
> - *
> - * Allocate or realloc buffer
> - * return value: 0, successful.
> - *
> - * -EINVAL, supplied buffer is too small.
> - *
> - * other, buffer could not be locked.
> - */
> -static int buf_prepare(struct videobuf_queue *vq, struct videobuf_buffer *vb,
> - enum v4l2_field field)
> + iowrite32((val), (vip->iomem)+(reg));
> +}
> +/* Read VIP register */
> +static inline u32 reg_read(struct sta2x11_vip *vip, unsigned int reg)
> {
> - struct sta2x11_vip *vip = vq->priv_data;
> - int ret;
> -
> - vb->size = vip->format.width * vip->format.height * 2;
> - if ((0 != vb->baddr) && (vb->bsize < vb->size))
> - return -EINVAL;
> - vb->width = vip->format.width;
> - vb->height = vip->format.height;
> - vb->field = field;
> -
> - if (VIDEOBUF_NEEDS_INIT == vb->state) {
> - ret = videobuf_iolock(vq, vb, NULL);
> - if (ret)
> - goto fail;
> - }
> - vb->state = VIDEOBUF_PREPARED;
> - return 0;
> -fail:
> - videobuf_dma_contig_free(vq, vb);
> - vb->state = VIDEOBUF_NEEDS_INIT;
> - return ret;
> + return ioread32((vip->iomem)+(reg));
> }
> -
> -/**
> - * buf_queu - queue buffer for filling
> - * @vq: queue in videobuf layer
> - * @vb: buffer to be queued
> - *
> - * if capturing is already running, the buffer will be queued. Otherwise
> - * capture is started and the buffer is used directly.
> - */
> -static void buf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb)
> +/* Start DMA acquisition */
> +static void start_dma(struct sta2x11_vip *vip, struct vip_buffer *vip_buf)
> {
> - struct sta2x11_vip *vip = vq->priv_data;
> - u32 dma;
> + unsigned long offset = 0;
>
> - vb->state = VIDEOBUF_QUEUED;
> + if (vip->format.field == V4L2_FIELD_INTERLACED)
> + offset = vip->format.width * 2;
>
> - if (vip->active) {
> - list_add_tail(&vb->queue, &vip->capture);
> + spin_lock_irq(&vip->slock);
> + /* Enable acquisition */
> + reg_write(vip, DVP_CTL, reg_read(vip, DVP_CTL) | DVP_CTL_ENA);
> + /* Set Top and Bottom Field memory address */
> + reg_write(vip, DVP_VTP, (u32)vip_buf->dma);
> + reg_write(vip, DVP_VBP, (u32)vip_buf->dma + offset);
> + spin_unlock_irq(&vip->slock);
> +}
> +
> +/* Fetch the next buffer to activate */
> +static void vip_active_buf_next(struct sta2x11_vip *vip)
> +{
> + /* Get the next buffer */
> + spin_lock(&vip->lock);
> + if (list_empty(&vip->buffer_list)) {/* No available buffer */
> + spin_unlock(&vip->lock);
> return;
> }
> -
> - vip->started = 1;
> + vip->active = list_first_entry(&vip->buffer_list,
> + struct vip_buffer,
> + list);
> + /* Reset Top and Bottom counter */
> vip->tcount = 0;
> vip->bcount = 0;
> - vip->active = vb;
> - vb->state = VIDEOBUF_ACTIVE;
> + spin_unlock(&vip->lock);
> + if (vb2_is_streaming(&vip->vb_vidq)) { /* streaming is on */
> + start_dma(vip, vip->active); /* start dma capture */
> + }
> +}
>
> - dma = videobuf_to_dma_contig(vb);
>
> - REG_WRITE(vip, DVP_TFO, (0 << 16) | (0));
> - /* despite of interlace mode, upper and lower frames start at zero */
> - REG_WRITE(vip, DVP_BFO, (0 << 16) | (0));
> +/* Videobuf2 Operations */
> +static int queue_setup(struct vb2_queue *vq, const struct v4l2_format *fmt,
> + unsigned int *nbuffers, unsigned int *nplanes,
> + unsigned int sizes[], void *alloc_ctxs[])
> +{
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vq);
>
> - switch (vip->format.field) {
> - case V4L2_FIELD_INTERLACED:
> - REG_WRITE(vip, DVP_TFS,
> - ((vip->format.height / 2 - 1) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_BFS, ((vip->format.height / 2 - 1) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_VTP, dma);
> - REG_WRITE(vip, DVP_VBP, dma + vip->format.width * 2);
> - REG_WRITE(vip, DVP_VMP, 4 * vip->format.width);
> - break;
> - case V4L2_FIELD_TOP:
> - REG_WRITE(vip, DVP_TFS,
> - ((vip->format.height - 1) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_BFS, ((0) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_VTP, dma);
> - REG_WRITE(vip, DVP_VBP, dma);
> - REG_WRITE(vip, DVP_VMP, 2 * vip->format.width);
> - break;
> - case V4L2_FIELD_BOTTOM:
> - REG_WRITE(vip, DVP_TFS, ((0) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_BFS,
> - ((vip->format.height) << 16) |
> - (2 * vip->format.width - 1));
> - REG_WRITE(vip, DVP_VTP, dma);
> - REG_WRITE(vip, DVP_VBP, dma);
> - REG_WRITE(vip, DVP_VMP, 2 * vip->format.width);
> - break;
> + if (!(*nbuffers) || *nbuffers < MAX_FRAMES)
> + *nbuffers = MAX_FRAMES;
>
> - default:
> - pr_warning("VIP: unknown field format\n");
> - return;
> - }
> + *nplanes = 1;
> + sizes[0] = vip->format.sizeimage;
> + alloc_ctxs[0] = vip->alloc_ctx;
>
> - REG_WRITE(vip, DVP_CTL, DVP_CTL_ENA);
> -}
> + vip->sequence = 0;
> + vip->active = NULL;
> + vip->tcount = 0;
> + vip->bcount = 0;
>
> -/**
> - * buff_release - release buffer
> - * @vq: queue in videobuf layer
> - * @vb: buffer to be released
> - *
> - * release buffer in videobuf layer
> - */
> -static void buf_release(struct videobuf_queue *vq, struct videobuf_buffer *vb)
> + return 0;
> +};
> +static int buffer_init(struct vb2_buffer *vb)
> {
> + struct vip_buffer *vip_buf = to_vip_buffer(vb);
>
> - videobuf_dma_contig_free(vq, vb);
> - vb->state = VIDEOBUF_NEEDS_INIT;
> + vip_buf->dma = vb2_dma_streaming_plane_paddr(vb, 0);
> + INIT_LIST_HEAD(&vip_buf->list);
> + return 0;
> }
>
> -static struct videobuf_queue_ops vip_qops = {
> - .buf_setup = buf_setup,
> - .buf_prepare = buf_prepare,
> - .buf_queue = buf_queue,
> - .buf_release = buf_release,
> -};
> -
> -/**
> - * vip_open - open video device
> - * @file: descriptor of device
> - *
> - * open device, make sure it is only opened once.
> - * return value: 0, no error.
> - *
> - * -EBUSY, device is already opened
> - *
> - * -ENOMEM, no memory for auxiliary DMA buffer
> - */
> -static int vip_open(struct file *file)
> +static int buffer_prepare(struct vb2_buffer *vb)
> {
> - struct video_device *dev = video_devdata(file);
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vb->vb2_queue);
> + struct vip_buffer *vip_buf = to_vip_buffer(vb);
> + unsigned long size;
> +
> + size = vip->format.sizeimage;
> + if (vb2_plane_size(vb, 0) < size) {
> + v4l2_err(&vip->v4l2_dev, "buffer too small (%lu < %lu)\n",
> + vb2_plane_size(vb, 0), size);
> + return -EINVAL;
> + }
>
> - mutex_lock(&vip->mutex);
> - vip->users++;
> + vb2_set_plane_payload(&vip_buf->vb, 0, size);
>
> - if (vip->users > 1) {
> - vip->users--;
> - mutex_unlock(&vip->mutex);
> - return -EBUSY;
> + return 0;
> +}
> +static void buffer_queue(struct vb2_buffer *vb)
> +{
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vb->vb2_queue);
> + struct vip_buffer *vip_buf = to_vip_buffer(vb);
> + unsigned long size;
> +
> + size = vip->format.sizeimage;
> + spin_lock(&vip->lock);
> + list_add_tail(&vip_buf->list, &vip->buffer_list);
> + if (!vip->active) { /* No active buffer, active the first one */
> + vip->active = list_first_entry(&vip->buffer_list,
> + struct vip_buffer,
> + list);
> + if (vb2_is_streaming(&vip->vb_vidq)) /* streaming is on */
> + start_dma(vip, vip_buf); /* start dma capture */
> }
> + spin_unlock(&vip->lock);
> +}
> +static int buffer_finish(struct vb2_buffer *vb)
> +{
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vb->vb2_queue);
> + struct vip_buffer *vip_buf = to_vip_buffer(vb);
> + unsigned long size;
>
> - file->private_data = dev;
> - vip->overflow = 0;
> - vip->started = 0;
> - vip->closing = 0;
> - vip->active = NULL;
> + /* Buffer handled, remove it from the list */
> + spin_lock(&vip->lock);
> + list_del_init(&vip_buf->list);
> + spin_unlock(&vip->lock);
> + /* DMA sync */
> + size = vip->format.sizeimage;
>
> - INIT_LIST_HEAD(&vip->capture);
> - vip->mem_spare = dma_alloc_coherent(&vip->pdev->dev, 64,
> - &vip->dma_spare, GFP_KERNEL);
> - if (!vip->mem_spare) {
> - vip->users--;
> - mutex_unlock(&vip->mutex);
> - return -ENOMEM;
> - }
> + vip_active_buf_next(vip);
>
> - mutex_unlock(&vip->mutex);
> - videobuf_queue_dma_contig_init_cached(&vip->vb_vidq,
> - &vip_qops,
> - &vip->pdev->dev,
> - &vip->slock,
> - V4L2_BUF_TYPE_VIDEO_CAPTURE,
> - V4L2_FIELD_INTERLACED,
> - sizeof(struct videobuf_buffer),
> - vip, NULL);
> - REG_READ(vip, DVP_ITS);
> - REG_WRITE(vip, DVP_HLFLN, DVP_HLFLN_SD);
> - REG_WRITE(vip, DVP_ITM, DVP_IT_VSB | DVP_IT_VST);
> - REG_WRITE(vip, DVP_CTL, DVP_CTL_RST);
> - REG_WRITE(vip, DVP_CTL, 0);
> - REG_READ(vip, DVP_ITS);
> return 0;
> }
>
> -/**
> - * vip_close - close video device
> - * @file: descriptor of device
> - *
> - * close video device, wait until all pending operations are finished
> - * ( maximum FRAME_MAX buffers pending )
> - * Turn off interrupts.
> - *
> - * return value: 0, always succesful.
> - */
> -static int vip_close(struct file *file)
> +static int start_streaming(struct vb2_queue *vq, unsigned int count)
> {
> - struct video_device *dev = video_devdata(file);
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vq);
>
> - vip->closing = 1;
> - if (vip->active)
> - videobuf_waiton(&vip->vb_vidq, vip->active, 0, 0);
> spin_lock_irq(&vip->slock);
> -
> - REG_WRITE(vip, DVP_ITM, 0);
> - REG_WRITE(vip, DVP_CTL, DVP_CTL_RST);
> - REG_WRITE(vip, DVP_CTL, 0);
> - REG_READ(vip, DVP_ITS);
> -
> - vip->started = 0;
> - vip->active = NULL;
> -
> + /* Enable interrupt VSYNC Top and Bottom*/
> + reg_write(vip, DVP_ITM, DVP_IT_VSB | DVP_IT_VST);
> spin_unlock_irq(&vip->slock);
>
> - videobuf_stop(&vip->vb_vidq);
> - videobuf_mmap_free(&vip->vb_vidq);
> + if (count)
> + start_dma(vip, vip->active);
>
> - dma_free_coherent(&vip->pdev->dev, 64, vip->mem_spare, vip->dma_spare);
> - file->private_data = NULL;
> - mutex_lock(&vip->mutex);
> - vip->users--;
> - mutex_unlock(&vip->mutex);
> return 0;
> }
>
> -/**
> - * vip_read - read from video input
> - * @file: descriptor of device
> - * @data: user buffer
> - * @count: number of bytes to be read
> - * @ppos: position within stream
> - *
> - * read video data from video device.
> - * handling is done in generic videobuf layer
> - * return value: provided by videobuf layer
> - */
> -static ssize_t vip_read(struct file *file, char __user *data,
> - size_t count, loff_t *ppos)
> +/* abort streaming and wait for last buffer */
> +static int stop_streaming(struct vb2_queue *vq)
> {
> - struct video_device *dev = file->private_data;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_read_stream(&vip->vb_vidq, data, count, ppos, 0,
> - file->f_flags & O_NONBLOCK);
> + struct sta2x11_vip *vip = vb2_get_drv_priv(vq);
> + struct vip_buffer *vip_buf, *node;
> +
> + /* Disable acquisition */
> + reg_write(vip, DVP_CTL, reg_read(vip, DVP_CTL) & ~DVP_CTL_ENA);
> + /* Disable all interrupts */
> + reg_write(vip, DVP_ITM, 0);
> +
> + /* Release all active buffers */
> + spin_lock(&vip->lock);
> + list_for_each_entry_safe(vip_buf, node, &vip->buffer_list, list) {
> + vb2_buffer_done(&vip_buf->vb, VB2_BUF_STATE_ERROR);
> + list_del(&vip_buf->list);
> + }
> + spin_unlock(&vip->lock);
> + return 0;
> }
>
> -/**
> - * vip_mmap - map user buffer
> - * @file: descriptor of device
> - * @vma: user buffer
> - *
> - * map user space buffer into kernel mode, including DMA address.
> - * handling is done in generic videobuf layer.
> - * return value: provided by videobuf layer
> - */
> -static int vip_mmap(struct file *file, struct vm_area_struct *vma)
> -{
> - struct video_device *dev = file->private_data;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> +static struct vb2_ops vip_video_qops = {
> + .queue_setup = queue_setup,
> + .buf_init = buffer_init,
> + .buf_prepare = buffer_prepare,
> + .buf_finish = buffer_finish,
> + .buf_queue = buffer_queue,
> + .start_streaming = start_streaming,
> + .stop_streaming = stop_streaming,
> +};
>
> - return videobuf_mmap_mapper(&vip->vb_vidq, vma);
> -}
>
> -/**
> - * vip_poll - poll for event
> - * @file: descriptor of device
> - * @wait: contains events to be waited for
> - *
> - * wait for event related to video device.
> - * handling is done in generic videobuf layer.
> - * return value: provided by videobuf layer
> - */
> -static unsigned int vip_poll(struct file *file, struct poll_table_struct *wait)
> -{
> - struct video_device *dev = file->private_data;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> +/* File Operations */
> +static const struct v4l2_file_operations vip_fops = {
> + .owner = THIS_MODULE,
> + .open = v4l2_fh_open,
> + .release = vb2_fop_release,
> + .unlocked_ioctl = video_ioctl2,
> + .read = vb2_fop_read,
> + .mmap = vb2_fop_mmap,
> + .poll = vb2_fop_poll
> +};
>
> - return videobuf_poll_stream(file, &vip->vb_vidq, wait);
> -}
>
> -/**
> - * vidioc_querycap - return capabilities of device
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @cap: contains return values
> - *
> - * the capabilities of the device are returned
> - *
> - * return value: 0, no error.
> - */
> +/* V4L2 ioctl Operations */
> static int vidioc_querycap(struct file *file, void *priv,
> struct v4l2_capability *cap)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
>
> - memset(cap, 0, sizeof(struct v4l2_capability));
> - strcpy(cap->driver, DRV_NAME);
> - strcpy(cap->card, DRV_NAME);
> - cap->version = 0;
> + strcpy(cap->driver, KBUILD_MODNAME);
> + strcpy(cap->card, KBUILD_MODNAME);
> snprintf(cap->bus_info, sizeof(cap->bus_info), "PCI:%s",
> pci_name(vip->pdev));
> - cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE |
> - V4L2_CAP_STREAMING;
> + cap->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE |
> + V4L2_CAP_STREAMING;
> + cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
>
> return 0;
> }
>
> -/**
> - * vidioc_s_std - set video standard
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @std: contains standard to be set
> - *
> - * the video standard is set
> - *
> - * return value: 0, no error.
> - *
> - * -EIO, no input signal detected
> - *
> - * other, returned from video DAC.
> - */
> static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id *std)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
> v4l2_std_id oldstd = vip->std, newstd;
> int status;
>
> @@ -590,110 +428,22 @@ static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id *std)
> return v4l2_subdev_call(vip->decoder, core, s_std, *std);
> }
>
> -/**
> - * vidioc_g_std - get video standard
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @std: contains return values
> - *
> - * the current video standard is returned
> - *
> - * return value: 0, no error.
> - */
> static int vidioc_g_std(struct file *file, void *priv, v4l2_std_id *std)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
>
> *std = vip->std;
> return 0;
> }
>
> -/**
> - * vidioc_querystd - get possible video standards
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @std: contains return values
> - *
> - * all possible video standards are returned
> - *
> - * return value: delivered by video DAC routine.
> - */
> static int vidioc_querystd(struct file *file, void *priv, v4l2_std_id *std)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
>
> return v4l2_subdev_call(vip->decoder, video, querystd, std);
>
> }
>
> -/**
> - * vidioc_queryctl - get possible control settings
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @ctrl: contains return values
> - *
> - * return possible values for a control
> - * return value: delivered by video DAC routine.
> - */
> -static int vidioc_queryctrl(struct file *file, void *priv,
> - struct v4l2_queryctrl *ctrl)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return v4l2_subdev_call(vip->decoder, core, queryctrl, ctrl);
> -}
> -
> -/**
> - * vidioc_g_ctl - get control value
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @ctrl: contains return values
> - *
> - * return setting for a control value
> - * return value: delivered by video DAC routine.
> - */
> -static int vidioc_g_ctrl(struct file *file, void *priv,
> - struct v4l2_control *ctrl)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return v4l2_subdev_call(vip->decoder, core, g_ctrl, ctrl);
> -}
> -
> -/**
> - * vidioc_s_ctl - set control value
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @ctrl: contains value to be set
> - *
> - * set value for a specific control
> - * return value: delivered by video DAC routine.
> - */
> -static int vidioc_s_ctrl(struct file *file, void *priv,
> - struct v4l2_control *ctrl)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return v4l2_subdev_call(vip->decoder, core, s_ctrl, ctrl);
> -}
> -
> -/**
> - * vidioc_enum_input - return name of input line
> - * @file: descriptor of device (not used)
> - * @priv: points to current videodevice
> - * @inp: contains return values
> - *
> - * the user friendly name of the input line is returned
> - *
> - * return value: 0, no error.
> - *
> - * -EINVAL, input line number out of range
> - */
> static int vidioc_enum_input(struct file *file, void *priv,
> struct v4l2_input *inp)
> {
> @@ -707,22 +457,9 @@ static int vidioc_enum_input(struct file *file, void *priv,
> return 0;
> }
>
> -/**
> - * vidioc_s_input - set input line
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @i: new input line number
> - *
> - * the current active input line is set
> - *
> - * return value: 0, no error.
> - *
> - * -EINVAL, line number out of range
> - */
> static int vidioc_s_input(struct file *file, void *priv, unsigned int i)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
> int ret;
>
> if (i > 1)
> @@ -735,36 +472,14 @@ static int vidioc_s_input(struct file *file, void *priv, unsigned int i)
> return 0;
> }
>
> -/**
> - * vidioc_g_input - return input line
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @i: returned input line number
> - *
> - * the current active input line is returned
> - *
> - * return value: always 0.
> - */
> static int vidioc_g_input(struct file *file, void *priv, unsigned int *i)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
>
> *i = vip->input;
> return 0;
> }
>
> -/**
> - * vidioc_enum_fmt_vid_cap - return video capture format
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @f: returned format information
> - *
> - * returns name and format of video capture
> - * Only UYVY is supported by hardware.
> - *
> - * return value: always 0.
> - */
> static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv,
> struct v4l2_fmtdesc *f)
> {
> @@ -778,32 +493,12 @@ static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv,
> return 0;
> }
>
> -/**
> - * vidioc_try_fmt_vid_cap - set video capture format
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @f: new format
> - *
> - * new video format is set which includes width and
> - * field type. width is fixed to 720, no scaling.
> - * Only UYVY is supported by this hardware.
> - * the minimum height is 200, the maximum is 576 (PAL)
> - *
> - * return value: 0, no error
> - *
> - * -EINVAL, pixel or field format not supported
> - *
> - */
> static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
> struct v4l2_format *f)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
> int interlace_lim;
>
> - if (V4L2_PIX_FMT_UYVY != f->fmt.pix.pixelformat)
> - return -EINVAL;
> -
> if (V4L2_STD_525_60 & vip->std)
> interlace_lim = 240;
> else
> @@ -827,6 +522,8 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
> return -EINVAL;
No -EINVAL allowed anymore in try_fmt_vid_cap. I generally handle unknown field
values in try_fmt_vid_cap as if FIELD_ANY was specified.
> }
>
> + /* It is the only supported format */
> + f->fmt.pix.pixelformat = V4L2_PIX_FMT_UYVY;
> f->fmt.pix.height &= ~1;
> if (2 * interlace_lim < f->fmt.pix.height)
> f->fmt.pix.height = 2 * interlace_lim;
> @@ -840,304 +537,222 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
> return 0;
> }
>
> -/**
> - * vidioc_s_fmt_vid_cap - set current video format parameters
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @f: returned format information
> - *
> - * set new capture format
> - * return value: 0, no error
> - *
> - * other, delivered by video DAC routine.
> - */
> static int vidioc_s_fmt_vid_cap(struct file *file, void *priv,
> struct v4l2_format *f)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
> + unsigned int t_stop, b_stop, pitch;
> int ret;
>
> ret = vidioc_try_fmt_vid_cap(file, priv, f);
> if (ret)
> return ret;
>
> + if (vb2_is_busy(&vip->vb_vidq)) {
> + /* Can't change format during acquisition */
> + v4l2_err(&vip->v4l2_dev, "device busy\n");
> + return -EBUSY;
> + }
> +
> memcpy(&vip->format, &f->fmt.pix, sizeof(struct v4l2_pix_format));
Just use an assignment: vip->format = f->fmt.pix
> + switch (vip->format.field) {
> + case V4L2_FIELD_INTERLACED:
> + t_stop = ((vip->format.height / 2 - 1) << 16) |
> + (2 * vip->format.width - 1);
> + b_stop = t_stop;
> + pitch = 4 * vip->format.width;
> + break;
> + case V4L2_FIELD_TOP:
> + t_stop = ((vip->format.height - 1) << 16) |
> + (2 * vip->format.width - 1);
> + b_stop = (0 << 16) | (2 * vip->format.width - 1);
> + pitch = 2 * vip->format.width;
> + break;
> + case V4L2_FIELD_BOTTOM:
> + t_stop = (0 << 16) | (2 * vip->format.width - 1);
> + b_stop = (vip->format.height << 16) |
> + (2 * vip->format.width - 1);
> + pitch = 2 * vip->format.width;
> + break;
> + default:
> + v4l2_err(&vip->v4l2_dev, "unknown field format\n");
> + return -EINVAL;
> + }
> +
> + spin_lock_irq(&vip->slock);
> + /* Y-X Top Field Offset */
> + reg_write(vip, DVP_TFO, 0);
> + /* Y-X Bottom Field Offset */
> + reg_write(vip, DVP_BFO, 0);
> + /* Y-X Top Field Stop*/
> + reg_write(vip, DVP_TFS, t_stop);
> + /* Y-X Bottom Field Stop */
> + reg_write(vip, DVP_BFS, b_stop);
> + /* Video Memory Pitch */
> + reg_write(vip, DVP_VMP, pitch);
> + spin_unlock_irq(&vip->slock);
> +
> return 0;
> }
>
> -/**
> - * vidioc_g_fmt_vid_cap - get current video format parameters
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @f: contains format information
> - *
> - * returns current video format parameters
> - *
> - * return value: 0, always successful
> - */
> static int vidioc_g_fmt_vid_cap(struct file *file, void *priv,
> struct v4l2_format *f)
> {
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> + struct sta2x11_vip *vip = video_drvdata(file);
>
> memcpy(&f->fmt.pix, &vip->format, sizeof(struct v4l2_pix_format));
Assignment
> return 0;
> }
>
> -/**
> - * vidioc_reqfs - request buffer
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @p: video buffer
> - *
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_reqbufs(struct file *file, void *priv,
> - struct v4l2_requestbuffers *p)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_reqbufs(&vip->vb_vidq, p);
> -}
> -
> -/**
> - * vidioc_querybuf - query buffer
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @p: video buffer
> - *
> - * query buffer state.
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_querybuf(struct file *file, void *priv, struct v4l2_buffer *p)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_querybuf(&vip->vb_vidq, p);
> -}
> -
> -/**
> - * vidioc_qbuf - queue a buffer
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @p: video buffer
> - *
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_qbuf(struct file *file, void *priv, struct v4l2_buffer *p)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_qbuf(&vip->vb_vidq, p);
> -}
> -
> -/**
> - * vidioc_dqbuf - dequeue a buffer
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @p: video buffer
> - *
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_dqbuf(struct file *file, void *priv, struct v4l2_buffer *p)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_dqbuf(&vip->vb_vidq, p, file->f_flags & O_NONBLOCK);
> -}
> -
> -/**
> - * vidioc_streamon - turn on streaming
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @type: type of capture
> - *
> - * turn on streaming.
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_streamon(struct file *file, void *priv,
> - enum v4l2_buf_type type)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_streamon(&vip->vb_vidq);
> -}
> -
> -/**
> - * vidioc_streamoff - turn off streaming
> - * @file: descriptor of device ( not used)
> - * @priv: points to current videodevice
> - * @type: type of capture
> - *
> - * turn off streaming.
> - * Handling is done in generic videobuf layer.
> - */
> -static int vidioc_streamoff(struct file *file, void *priv,
> - enum v4l2_buf_type type)
> -{
> - struct video_device *dev = priv;
> - struct sta2x11_vip *vip = video_get_drvdata(dev);
> -
> - return videobuf_streamoff(&vip->vb_vidq);
> -}
> -
> -static const struct v4l2_file_operations vip_fops = {
> - .owner = THIS_MODULE,
> - .open = vip_open,
> - .release = vip_close,
> - .ioctl = video_ioctl2,
> - .read = vip_read,
> - .mmap = vip_mmap,
> - .poll = vip_poll
> -};
> -
> static const struct v4l2_ioctl_ops vip_ioctl_ops = {
> .vidioc_querycap = vidioc_querycap,
> - .vidioc_s_std = vidioc_s_std,
> + /* FMT handling */
> + .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap,
> + .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap,
> + .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap,
> + .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap,
> + /* Buffer handlers */
> + .vidioc_reqbufs = vb2_ioctl_reqbufs,
> + .vidioc_querybuf = vb2_ioctl_querybuf,
> + .vidioc_qbuf = vb2_ioctl_qbuf,
> + .vidioc_dqbuf = vb2_ioctl_dqbuf,
> + .vidioc_create_bufs = vb2_ioctl_create_bufs,
If you want to use create_bufs, then in queue_setup() you need to handle the
fmt argument. See e.g. vivi.c for an example.
> + /* Stream on/off */
> + .vidioc_streamon = vb2_ioctl_streamon,
> + .vidioc_streamoff = vb2_ioctl_streamoff,
> + /* Standard handling */
> .vidioc_g_std = vidioc_g_std,
> + .vidioc_s_std = vidioc_s_std,
> .vidioc_querystd = vidioc_querystd,
> - .vidioc_queryctrl = vidioc_queryctrl,
> - .vidioc_g_ctrl = vidioc_g_ctrl,
> - .vidioc_s_ctrl = vidioc_s_ctrl,
> + /* Input handling */
> .vidioc_enum_input = vidioc_enum_input,
> - .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap,
> - .vidioc_s_input = vidioc_s_input,
> .vidioc_g_input = vidioc_g_input,
> - .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap,
> - .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap,
> - .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap,
> - .vidioc_reqbufs = vidioc_reqbufs,
> - .vidioc_querybuf = vidioc_querybuf,
> - .vidioc_qbuf = vidioc_qbuf,
> - .vidioc_dqbuf = vidioc_dqbuf,
> - .vidioc_streamon = vidioc_streamon,
> - .vidioc_streamoff = vidioc_streamoff,
> + .vidioc_s_input = vidioc_s_input,
> + /* Log status ioctl */
> + .vidioc_log_status = v4l2_ctrl_log_status,
> + /* Event handling */
> + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
> + .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
> };
>
> static struct video_device video_dev_template = {
> - .name = DRV_NAME,
> + .name = KBUILD_MODNAME,
> .release = video_device_release,
> .fops = &vip_fops,
> .ioctl_ops = &vip_ioctl_ops,
> .tvnorms = V4L2_STD_ALL,
> };
>
> -/**
> - * vip_irq - interrupt routine
> - * @irq: Number of interrupt ( not used, correct number is assumed )
> - * @vip: local data structure containing all information
> - *
> - * check for both frame interrupts set ( top and bottom ).
> - * check FIFO overflow, but limit number of log messages after open.
> - * signal a complete buffer if done.
> - * dequeue a new buffer if available.
> - * disable VIP if no buffer available.
> - *
> - * return value: IRQ_NONE, interrupt was not generated by VIP
> - *
> - * IRQ_HANDLED, interrupt done.
> - */
> +
> static irqreturn_t vip_irq(int irq, struct sta2x11_vip *vip)
> {
> - u32 status, dma;
> - unsigned long flags;
> - struct videobuf_buffer *vb;
> + unsigned int status;
>
> - status = REG_READ(vip, DVP_ITS);
> + status = reg_read(vip, DVP_ITS);
>
> - if (!status) {
> - pr_debug("VIP: irq ignored\n");
> + if (!status) /* No interrupt to handle */
> return IRQ_NONE;
> - }
>
> - if (!vip->started)
> - return IRQ_HANDLED;
> -
> - if (status & DVP_IT_VSB)
> - vip->bcount++;
> -
> - if (status & DVP_IT_VST)
> - vip->tcount++;
> + if (status & DVP_IT_FIFO)
> + if (vip->overflow++ > 5)
> + pr_info("VIP: fifo overflow\n");
>
> - if ((DVP_IT_VSB | DVP_IT_VST) == (status & (DVP_IT_VST | DVP_IT_VSB))) {
> + if ((status & DVP_IT_VST) && (status & DVP_IT_VSB)) {
> /* this is bad, we are too slow, hope the condition is gone
> * on the next frame */
> - pr_info("VIP: both irqs\n");
> return IRQ_HANDLED;
> }
>
> - if (status & DVP_IT_FIFO) {
> - if (5 > vip->overflow++)
> - pr_info("VIP: fifo overflow\n");
> - }
> -
> - if (2 > vip->tcount)
> + if (status & DVP_IT_VST)
> + if ((++vip->tcount) < 2)
> + return IRQ_HANDLED;
> + if (status & DVP_IT_VSB) {
> + vip->bcount++;
> return IRQ_HANDLED;
> + }
>
> - if (status & DVP_IT_VSB)
> - return IRQ_HANDLED;
> + if (vip->active) { /* Acquisition is over on this buffer */
> + /* Disable acquisition */
> + reg_write(vip, DVP_CTL, reg_read(vip, DVP_CTL) & ~DVP_CTL_ENA);
> + /* Remove the active buffer from the list */
> + do_gettimeofday(&vip->active->vb.v4l2_buf.timestamp);
> + vip->active->vb.v4l2_buf.sequence = vip->sequence++;
> + vb2_buffer_done(&vip->active->vb, VB2_BUF_STATE_DONE);
> + }
>
> - spin_lock_irqsave(&vip->slock, flags);
> + return IRQ_HANDLED;
> +}
>
> - REG_WRITE(vip, DVP_CTL, REG_READ(vip, DVP_CTL) & ~DVP_CTL_ENA);
> - if (vip->active) {
> - do_gettimeofday(&vip->active->ts);
> - vip->active->field_count++;
> - vip->active->state = VIDEOBUF_DONE;
> - wake_up(&vip->active->done);
> - vip->active = NULL;
> +static void sta2x11_vip_init_register(struct sta2x11_vip *vip)
> +{
> + /* Register initialization */
> + spin_lock_irq(&vip->slock);
> + /* Clean interrupt */
> + reg_read(vip, DVP_ITS);
> + /* Enable Half Line per vertical */
> + reg_write(vip, DVP_HLFLN, DVP_HLFLN_SD);
> + /* Reset VIP control */
> + reg_write(vip, DVP_CTL, DVP_CTL_RST);
> + /* Clear VIP control */
> + reg_write(vip, DVP_CTL, 0);
> + spin_unlock_irq(&vip->slock);
> +}
> +static void sta2x11_vip_clear_register(struct sta2x11_vip *vip)
> +{
> + spin_lock_irq(&vip->slock);
> + /* Disable interrupt */
> + reg_write(vip, DVP_ITM, 0);
> + /* Reset VIP Control */
> + reg_write(vip, DVP_CTL, DVP_CTL_RST);
> + /* Clear VIP Control */
> + reg_write(vip, DVP_CTL, 0);
> + /* Clean VIP Interrupt */
> + reg_read(vip, DVP_ITS);
> + spin_unlock_irq(&vip->slock);
> +}
> +static int sta2x11_vip_init_buffer(struct sta2x11_vip *vip)
> +{
> + memset(&vip->vb_vidq, 0, sizeof(struct vb2_queue));
> + vip->vb_vidq.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
> + vip->vb_vidq.io_modes = VB2_MMAP | VB2_READ;
> + vip->vb_vidq.drv_priv = vip;
> + vip->vb_vidq.buf_struct_size = sizeof(struct vip_buffer);
> + vip->vb_vidq.ops = &vip_video_qops;
> + vip->vb_vidq.mem_ops = &vb2_dma_streaming_memops;
> + vb2_queue_init(&vip->vb_vidq);
> + INIT_LIST_HEAD(&vip->buffer_list);
> + spin_lock_init(&vip->lock);
> +
> + vip->alloc_ctx = vb2_dma_streaming_init_ctx(&vip->pdev->dev);
> + if (IS_ERR(vip->alloc_ctx)) {
> + v4l2_err(&vip->v4l2_dev, "Can't allocate buffer context");
> + return PTR_ERR(vip->alloc_ctx);
> }
> - if (!vip->closing) {
> - if (list_empty(&vip->capture))
> - goto done;
> -
> - vb = list_first_entry(&vip->capture, struct videobuf_buffer,
> - queue);
> - if (NULL == vb) {
> - pr_info("VIP: no buffer\n");
> - goto done;
> - }
> - vb->state = VIDEOBUF_ACTIVE;
> - list_del(&vb->queue);
> - vip->active = vb;
> - dma = videobuf_to_dma_contig(vb);
> - switch (vip->format.field) {
> - case V4L2_FIELD_INTERLACED:
> - REG_WRITE(vip, DVP_VTP, dma);
> - REG_WRITE(vip, DVP_VBP, dma + vip->format.width * 2);
> - break;
> - case V4L2_FIELD_TOP:
> - case V4L2_FIELD_BOTTOM:
> - REG_WRITE(vip, DVP_VTP, dma);
> - REG_WRITE(vip, DVP_VBP, dma);
> - break;
> - default:
> - pr_warning("VIP: unknown field format\n");
> - goto done;
> - break;
> - }
> - REG_WRITE(vip, DVP_CTL, REG_READ(vip, DVP_CTL) | DVP_CTL_ENA);
> + return 0;
> +}
> +static void sta2x11_vip_release_buffer(struct sta2x11_vip *vip)
> +{
> + vb2_dma_streaming_cleanup_ctx(vip->alloc_ctx);
> +}
> +static int sta2x11_vip_init_controls(struct sta2x11_vip *vip)
> +{
> + /*
> + * Inititialize an empty control so VIP can inerithing controls
> + * from ADV7180
> + */
> + v4l2_ctrl_handler_init(&vip->ctrl_hdl, 0);
> +
> + vip->v4l2_dev.ctrl_handler = &vip->ctrl_hdl;
> + if (vip->ctrl_hdl.error) {
> + int err = vip->ctrl_hdl.error;
> +
> + v4l2_ctrl_handler_free(&vip->ctrl_hdl);
> + return err;
> }
> -done:
> - spin_unlock_irqrestore(&vip->slock, flags);
> - return IRQ_HANDLED;
> +
> + return 0;
> }
>
> -/**
> - * vip_gpio_reserve - reserve gpio pin
> - * @dev: device
> - * @pin: GPIO pin number
> - * @dir: direction, input or output
> - * @name: GPIO pin name
> - *
> - */
> static int vip_gpio_reserve(struct device *dev, int pin, int dir,
> const char *name)
> {
> @@ -1170,13 +785,6 @@ static int vip_gpio_reserve(struct device *dev, int pin, int dir,
> return 0;
> }
>
> -/**
> - * vip_gpio_release - release gpio pin
> - * @dev: device
> - * @pin: GPIO pin number
> - * @name: GPIO pin name
> - *
> - */
> static void vip_gpio_release(struct device *dev, int pin, const char *name)
> {
> if (pin != -1) {
> @@ -1186,25 +794,6 @@ static void vip_gpio_release(struct device *dev, int pin, const char *name)
> }
> }
>
> -/**
> - * sta2x11_vip_init_one - init one instance of video device
> - * @pdev: PCI device
> - * @ent: (not used)
> - *
> - * allocate reset pins for DAC.
> - * Reset video DAC, this is done via reset line.
> - * allocate memory for managing device
> - * request interrupt
> - * map IO region
> - * register device
> - * find and initialize video DAC
> - *
> - * return value: 0, no error
> - *
> - * -ENOMEM, no memory
> - *
> - * -ENODEV, device could not be detected or registered
> - */
> static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> const struct pci_device_id *ent)
> {
> @@ -1212,10 +801,17 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> struct sta2x11_vip *vip;
> struct vip_config *config;
>
> + /* Check if hardware support 26-bit DMA */
> + if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(26))) {
> + dev_err(&pdev->dev, "26-bit DMA addressing not available\n");
> + return -EINVAL;
> + }
> + /* Enable PCI */
> ret = pci_enable_device(pdev);
> if (ret)
> return ret;
>
> + /* Get VIP platform data */
> config = dev_get_platdata(&pdev->dev);
> if (!config) {
> dev_info(&pdev->dev, "VIP slot disabled\n");
> @@ -1223,6 +819,7 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> goto disable;
> }
>
> + /* Power configuration */
> ret = vip_gpio_reserve(&pdev->dev, config->pwr_pin, 0,
> config->pwr_name);
> if (ret)
> @@ -1237,7 +834,6 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> goto disable;
> }
> }
> -
> if (config->pwr_pin != -1) {
> /* Datasheet says 5ms between PWR and RST */
> usleep_range(5000, 25000);
> @@ -1251,17 +847,20 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> }
> usleep_range(5000, 25000);
>
> + /* Allocate a new VIP instance */
> vip = kzalloc(sizeof(struct sta2x11_vip), GFP_KERNEL);
> if (!vip) {
> ret = -ENOMEM;
> goto release_gpios;
> }
> -
> vip->pdev = pdev;
> vip->std = V4L2_STD_PAL;
> vip->format = formats_50[0];
> vip->config = config;
>
> + ret = sta2x11_vip_init_controls(vip);
> + if (ret)
> + goto free_mem;
> if (v4l2_device_register(&pdev->dev, &vip->v4l2_dev))
> goto free_mem;
>
> @@ -1271,46 +870,52 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
>
> pci_set_master(pdev);
>
> - ret = pci_request_regions(pdev, DRV_NAME);
> + ret = pci_request_regions(pdev, KBUILD_MODNAME);
> if (ret)
> goto unreg;
>
> vip->iomem = pci_iomap(pdev, 0, 0x100);
> if (!vip->iomem) {
> - ret = -ENOMEM; /* FIXME */
> + ret = -ENOMEM;
> goto release;
> }
>
> pci_enable_msi(pdev);
>
> - INIT_LIST_HEAD(&vip->capture);
> + /* Initialize buffer */
> + ret = sta2x11_vip_init_buffer(vip);
> + if (ret)
> + goto unmap;
> +
> spin_lock_init(&vip->slock);
> - mutex_init(&vip->mutex);
> - vip->started = 0;
> - vip->disabled = 0;
>
> ret = request_irq(pdev->irq,
> (irq_handler_t) vip_irq,
> - IRQF_SHARED, DRV_NAME, vip);
> + IRQF_SHARED, KBUILD_MODNAME, vip);
> if (ret) {
> dev_err(&pdev->dev, "request_irq failed\n");
> ret = -ENODEV;
> - goto unmap;
> + goto release_buf;
> }
>
> + /* Alloc, initialize and register video device */
> vip->video_dev = video_device_alloc();
> if (!vip->video_dev) {
> ret = -ENOMEM;
> goto release_irq;
> }
>
> - *(vip->video_dev) = video_dev_template;
> + vip->video_dev = &video_dev_template;
> + vip->video_dev->v4l2_dev = &vip->v4l2_dev;
> + vip->video_dev->queue = &vip->vb_vidq;
> + set_bit(V4L2_FL_USE_FH_PRIO, &vip->video_dev->flags);
> video_set_drvdata(vip->video_dev, vip);
>
> ret = video_register_device(vip->video_dev, VFL_TYPE_GRABBER, -1);
> if (ret)
> goto vrelease;
>
> + /* Get ADV7180 subdevice */
> vip->adapter = i2c_get_adapter(vip->config->i2c_id);
> if (!vip->adapter) {
> ret = -ENODEV;
> @@ -1328,10 +933,11 @@ static int __devinit sta2x11_vip_init_one(struct pci_dev *pdev,
> }
>
> i2c_put_adapter(vip->adapter);
> -
> v4l2_subdev_call(vip->decoder, core, init, 0);
>
> - pr_info("STA2X11 Video Input Port (VIP) loaded\n");
> + sta2x11_vip_init_register(vip);
> +
> + dev_info(&pdev->dev, "STA2X11 Video Input Port (VIP) loaded\n");
> return 0;
>
> vunreg:
> @@ -1343,10 +949,12 @@ vrelease:
> video_device_release(vip->video_dev);
> release_irq:
> free_irq(pdev->irq, vip);
> +release_buf:
> + sta2x11_vip_release_buffer(vip);
> pci_disable_msi(pdev);
> unmap:
> + vb2_queue_release(&vip->vb_vidq);
> pci_iounmap(pdev, vip->iomem);
> - mutex_destroy(&vip->mutex);
> release:
> pci_release_regions(pdev);
> unreg:
> @@ -1364,34 +972,24 @@ disable:
> return ret;
> }
>
> -/**
> - * sta2x11_vip_remove_one - release device
> - * @pdev: PCI device
> - *
> - * Undo everything done in .._init_one
> - *
> - * unregister video device
> - * free interrupt
> - * unmap ioadresses
> - * free memory
> - * free GPIO pins
> - */
> static void __devexit sta2x11_vip_remove_one(struct pci_dev *pdev)
> {
> struct v4l2_device *v4l2_dev = pci_get_drvdata(pdev);
> struct sta2x11_vip *vip =
> container_of(v4l2_dev, struct sta2x11_vip, v4l2_dev);
>
> + sta2x11_vip_clear_register(vip);
> +
> video_set_drvdata(vip->video_dev, NULL);
> video_unregister_device(vip->video_dev);
> /*do not call video_device_release() here, is already done */
> free_irq(pdev->irq, vip);
> pci_disable_msi(pdev);
> + vb2_queue_release(&vip->vb_vidq);
> pci_iounmap(pdev, vip->iomem);
> pci_release_regions(pdev);
>
> v4l2_device_unregister(&vip->v4l2_dev);
> - mutex_destroy(&vip->mutex);
>
> vip_gpio_release(&pdev->dev, vip->config->pwr_pin,
> vip->config->pwr_name);
> @@ -1407,18 +1005,12 @@ static void __devexit sta2x11_vip_remove_one(struct pci_dev *pdev)
>
> #ifdef CONFIG_PM
>
> -/**
> - * sta2x11_vip_suspend - set device into power save mode
> - * @pdev: PCI device
> - * @state: new state of device
> +/*
> *
> * all relevant registers are saved and an attempt to set a new state is made.
> *
> * return value: 0 always indicate success,
> * even if device could not be disabled. (workaround for hardware problem)
> - *
> - * reurn value : 0, always succesful, even if hardware does not not support
> - * power down mode.
> */
> static int sta2x11_vip_suspend(struct pci_dev *pdev, pm_message_t state)
> {
> @@ -1429,15 +1021,15 @@ static int sta2x11_vip_suspend(struct pci_dev *pdev, pm_message_t state)
> int i;
>
> spin_lock_irqsave(&vip->slock, flags);
> - vip->register_save_area[0] = REG_READ(vip, DVP_CTL);
> - REG_WRITE(vip, DVP_CTL, vip->register_save_area[0] & DVP_CTL_DIS);
> - vip->register_save_area[SAVE_COUNT] = REG_READ(vip, DVP_ITM);
> - REG_WRITE(vip, DVP_ITM, 0);
> + vip->register_save_area[0] = reg_read(vip, DVP_CTL);
> + reg_write(vip, DVP_CTL, vip->register_save_area[0] & DVP_CTL_DIS);
> + vip->register_save_area[SAVE_COUNT] = reg_read(vip, DVP_ITM);
> + reg_write(vip, DVP_ITM, 0);
> for (i = 1; i < SAVE_COUNT; i++)
> - vip->register_save_area[i] = REG_READ(vip, 4 * i);
> + vip->register_save_area[i] = reg_read(vip, 4 * i);
> for (i = 0; i < AUX_COUNT; i++)
> vip->register_save_area[SAVE_COUNT + IRQ_COUNT + i] =
> - REG_READ(vip, registers_to_save[i]);
> + reg_read(vip, registers_to_save[i]);
> spin_unlock_irqrestore(&vip->slock, flags);
> /* save pci state */
> pci_save_state(pdev);
> @@ -1453,16 +1045,9 @@ static int sta2x11_vip_suspend(struct pci_dev *pdev, pm_message_t state)
> return 0;
> }
>
> -/**
> - * sta2x11_vip_resume - resume device operation
> - * @pdev : PCI device
> - *
> +/*
> * re-enable device, set PCI state to powered and restore registers.
> * resume normal device operation afterwards.
> - *
> - * return value: 0, no error.
> - *
> - * other, could not set device to power on state.
> */
> static int sta2x11_vip_resume(struct pci_dev *pdev)
> {
> @@ -1497,12 +1082,12 @@ static int sta2x11_vip_resume(struct pci_dev *pdev)
>
> spin_lock_irqsave(&vip->slock, flags);
> for (i = 1; i < SAVE_COUNT; i++)
> - REG_WRITE(vip, 4 * i, vip->register_save_area[i]);
> + reg_write(vip, 4 * i, vip->register_save_area[i]);
> for (i = 0; i < AUX_COUNT; i++)
> - REG_WRITE(vip, registers_to_save[i],
> + reg_write(vip, registers_to_save[i],
> vip->register_save_area[SAVE_COUNT + IRQ_COUNT + i]);
> - REG_WRITE(vip, DVP_CTL, vip->register_save_area[0]);
> - REG_WRITE(vip, DVP_ITM, vip->register_save_area[SAVE_COUNT]);
> + reg_write(vip, DVP_CTL, vip->register_save_area[0]);
> + reg_write(vip, DVP_ITM, vip->register_save_area[SAVE_COUNT]);
> spin_unlock_irqrestore(&vip->slock, flags);
> return 0;
> }
> @@ -1515,7 +1100,7 @@ static DEFINE_PCI_DEVICE_TABLE(sta2x11_vip_pci_tbl) = {
> };
>
> static struct pci_driver sta2x11_vip_driver = {
> - .name = DRV_NAME,
> + .name = KBUILD_MODNAME,
> .probe = sta2x11_vip_init_one,
> .remove = __devexit_p(sta2x11_vip_remove_one),
> .id_table = sta2x11_vip_pci_tbl,
> @@ -1543,7 +1128,7 @@ late_initcall_sync(sta2x11_vip_init_module);
> #endif
>
> MODULE_DESCRIPTION("STA2X11 Video Input Port driver");
> -MODULE_AUTHOR("Wind River");
> +MODULE_AUTHOR("Federico Vaga <federico.vaga@xxxxxxxxx>");
> MODULE_LICENSE("GPL v2");
> MODULE_SUPPORTED_DEVICE("sta2x11 video input");
> MODULE_VERSION(DRV_VERSION);
>
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
