On Thu 13 September 2012 11:48:17 javier Martin wrote: > Hi, > our new i.MX27 based platform (Visstrim-SM20) uses an ov7675 sensor > attached to the CSI interface. Apparently, this sensor is fully > compatible with the old ov7670. For this reason, it seems rather > sensible that they should share the same driver: ov7670.c > One of the challenges we have to face is that capture video support > for our platform is mx2_camera.c, which is a soc-camera host driver; > while ov7670.c was developed for being used as part of a more complex > video card. > > Here is the list of current users of ov7670: > > http://lxr.linux.no/#linux+v3.5.3/drivers/media/video/gspca/ov519.c > http://lxr.linux.no/#linux+v3.5.3/drivers/media/video/gspca/sn9c20x.c > http://lxr.linux.no/#linux+v3.5.3/drivers/media/video/gspca/vc032x.c These do not actually use the ov7670 driver. They program it themselves. It would be nice if the gspca driver would get support for subdevs, but that's a separate topic. > http://lxr.linux.no/#linux+v3.5.3/drivers/media/video/via-camera.c > http://lxr.linux.no/#linux+v3.5.3/drivers/media/video/marvell-ccic/mcam-core.c > > These are basically the improvements we need to make to this driver in > order to satisfy our needs: > > 1.- Adapt v4l2 controls to the subvevice control framework, with a > proper ctrl handler, etc... > 2.- Add the possibility to bypass PLL and clkrc preescaler. > 3.- Adjust vstart/vstop in order to remove an horizontal green line. > 4.- Disable pixclk during horizontal blanking. > 5.- min_height, min_width should be respected in try_fmt(). > 6.- Pass platform data when used with a soc-camera host driver. > 7.- Add V4L2_CID_POWER_LINE_FREQUENCY ctrl. > > I will try to summarize below why we need to accomplish each of the > previous tasks and what solution we propose for them: > > 1.- Adapt v4l2 controls to the subvevice control framework, with a > proper ctrl handler, etc... > > Why? Because soc-camera needs to inherit v4l2 subdevice controls in > order to expose them to user space. > How? Something like the following, incomplete, patch: Luckily you didn't do too much work on this. I have old patches for this in this tree: http://git.linuxtv.org/hverkuil/media_tree.git/shortlog/refs/heads/cafe-ctrl The main reason why I never continued with this was that at the time I wrote this I realized that the control framework needed proper support for what's now called auto-clusters (i.e. how to handle autofoo/foo controls like autogain and gain correctly). I intended to pick this up at some time, but never got around to it. I think these patches will still apply with some work, but it needs to be converted to use the autocluster support that's now in the control framework. > > --- > @@ -190,6 +196,7 @@ MODULE_PARM_DESC(debug, "Debug level (0-1)"); > struct ov7670_format_struct; /* coming later */ > struct ov7670_info { > struct v4l2_subdev sd; > + struct v4l2_ctrl_handler hdl; > struct ov7670_format_struct *fmt; /* Current format */ > unsigned char sat; /* Saturation value */ > int hue; /* Hue value */ > > > @@ -1480,10 +1518,14 @@ static int ov7670_s_register(struct > v4l2_subdev *sd, struct v4l2_dbg_register *r > > /* ----------------------------------------------------------------------- */ > > +static const struct v4l2_ctrl_ops ov7670_ctrl_ops = { > + .s_ctrl = ov7670_s_ctrl, > +}; > + > static const struct v4l2_subdev_core_ops ov7670_core_ops = { > .g_chip_ident = ov7670_g_chip_ident, > - .g_ctrl = ov7670_g_ctrl, > - .s_ctrl = ov7670_s_ctrl, > + .g_ctrl = v4l2_subdev_g_ctrl, > + .s_ctrl = v4l2_subdev_s_ctrl, > .queryctrl = ov7670_queryctrl, > .reset = ov7670_reset, > .init = ov7670_init, > > @@ -1551,6 +1600,16 @@ static int ov7670_probe(struct i2c_client *client, > v4l_info(client, "chip found @ 0x%02x (%s)\n", > client->addr << 1, client->adapter->name); > > + v4l2_ctrl_handler_init(&info->hdl, 1); > + v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, > V4L2_CID_VFLIP, 0, 1, 1, 0); > ... > ... > + sd->ctrl_handler = &info->hdl; > + if (info->hdl.error) { > + v4l2_ctrl_handler_free(&info->hdl); > + kfree(info); > + return info->hdl.error; > + } > + v4l2_ctrl_handler_setup(&info->hdl); > + > --- > > 2.- Add the possibility to bypass PLL and clkrc preescaler. > > Why? The formula to get the desired frame rate in this chip in YUV is > the following: fps = fpclk / (2 * 510 * 784) This means that for a > desired fps = 30 we need fpclk = 24MHz. For that reason we have a > clean 24MHz xvclk input that comes from an oscillator. If we enable > the PLL it internally transforms the 24MHz in 22MHz and thus fps is > not 30 but 27. In order to get 30fps we need to bypass the PLL. > How? Defining a platform flag 'direct_clk' or similar that allows > xvclk being used directly as the pixel clock. > > 3.- Adjust vstart/vstop in order to remove an horizontal green line. > > Why? Currently, in the driver, for VGA, vstart = 10 and vstop = 490. > From our tests we found out that vstart = 14, vstop = 494 in order to > remove a disgusting horizontal green line in ov7675. > How? It seems these sensor aren't provided with a version register or > anything similar so I can't think of a clean solution for this yet. > Suggestions will be much appreciated. Using platform_data for this is what springs to mind. > 4.- Disable pixclk during horizontal blanking. > > Why? Otherwise i.MX27 will capture wrong pixels during blanking periods. > How? Through a private V4L2 control. Or platform_data as well? > 5.- min_height, min_width should be respected in try_fmt(). > Why? Otherwise you are telling the user you are going to use a > different size than the one you are going to use. > How? With a patch similar to this: > > --- > @@ -759,8 +772,10 @@ static int ov7670_try_fmt_internal(struct v4l2_subdev *sd, > struct ov7670_format_struct **ret_fmt, > struct ov7670_win_size **ret_wsize) > { > - int index; > + int index, i; > + int win_sizes_limit = N_WIN_SIZES; > struct ov7670_win_size *wsize; > + struct ov7670_info *info = to_state(sd); > > for (index = 0; index < N_OV7670_FMTS; index++) > if (ov7670_formats[index].mbus_code == fmt->code) > @@ -776,15 +791,30 @@ static int ov7670_try_fmt_internal(struct v4l2_subdev *sd, > * Fields: the OV devices claim to be progressive. > */ > fmt->field = V4L2_FIELD_NONE; > + > + /* > + * Don't consider values that don't match min_height and min_width > + * constraints. > + */ > + if (info->min_width || info->min_height) > + for (i=0; i < N_WIN_SIZES; i++) { > + wsize = ov7670_win_sizes + i; > + > + if (wsize->width < info->min_width || > + wsize->height < info->min_height) { > + win_sizes_limit = i; > + break; > + } > + } > /* > * Round requested image size down to the nearest > * we support, but not below the smallest. > */ > - for (wsize = ov7670_win_sizes; wsize < ov7670_win_sizes + N_WIN_SIZES; > + for (wsize = ov7670_win_sizes; wsize < ov7670_win_sizes + > win_sizes_limit; > wsize++) > if (fmt->width >= wsize->width && fmt->height >= wsize->height) > break; > - if (wsize >= ov7670_win_sizes + N_WIN_SIZES) > + if (wsize >= ov7670_win_sizes + win_sizes_limit) > wsize--; /* Take the smallest one */ > if (ret_wsize != NULL) > *ret_wsize = wsize; > --- > > 6.- Pass platform data when used with a soc-camera host driver. > Why? We need to set several platform data like 'min_height', > 'min_width' and others. > How? This is an old subject we discussed in January. We agreed that > some soc-camera core changes were needed, but I couldn't find the time > and I think nobody else has addressed it either. Please, correct me if > I am wrong:http://patchwork.linuxtv.org/patch/8860/ > > 7.- Add V4L2_CID_POWER_LINE_FREQUENCY ctrl. > Why? Because the platform will be used in several countries. > How? As long as point 1 is solved this is quite trivial. > > > The reason of this e-mail is to discuss whether you find these > solution suitable or not and, more important, whether you think the > suggested changes could break existing drivers. Well, those bridge drivers that use the ov7670 subdev should also be converted to the control framework. My tree does at least some of that work, although I think some drivers got moved around or were renamed. The changes to those drivers should be fairly minimal. In theory it's possible to skip that conversion, but my goal is to get (almost) all drivers converted to the control framework so this is a good opportunity to convert these bridge drivers at the same time. Regards, Hans -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
