On 07/30/2012 07:07 PM, poma wrote: > On 07/30/2012 02:56 PM, David Basden wrote: >>>>>> Right now I really don't know where I should look for the solution of >>>>>> the problem. It seems that the tuner reset does not have any effect on the >>>>>> tuner whatsoever. >> >> Can I suggest setting GPIO5 to 1, leave it there, and see if it breaks. If it >> doesn't, GPIO5 on the RTL isn't setup correctly somehow. >> >> At the same time, I was rereading code from: >> >> http://git.linuxtv.org/anttip/media_tree.git/blob/3efd26330fda97e06279cbca170ae4a0dee53220:/drivers/media/dvb/dvb-usb/rtl28xxu.c#l898 >> >> and at no point is GPIO5 actually set to an output or enabled that I can find. >> rtl2832u_frontend_attach skips doing so. (Actually, I seem to remember running >> into this problem while trying to use some DVB driver code as an example of >> how to setup the RTL to talk to the FC0012) >> >> Try giving the patch below a go. Sorry, I don't have a build environment to >> hand, so there might be a typo I haven't picked up, but the upshot is that >> I'm moving the FC0012 detection to the end, setting up GPIO5, resetting the >> tuner and then trying to probe for the FC0012. >> >> Please let me know if this helps :) >> >> David >> >> --- a/rtl28xxu.c 2012-07-30 22:31:53.789638678 +1000 >> +++ b/rtl28xxu.c 2012-07-30 22:48:35.774607232 +1000 >> @@ -550,15 +550,6 @@ >> >> priv->tuner = TUNER_NONE; >> >> - /* check FC0012 ID register; reg=00 val=a1 */ >> - ret = rtl28xxu_ctrl_msg(adap->dev, &req_fc0012); >> - if (ret == 0 && buf[0] == 0xa1) { >> - priv->tuner = TUNER_RTL2832_FC0012; >> - rtl2832_config = &rtl28xxu_rtl2832_fc0012_config; >> - info("%s: FC0012 tuner found", __func__); >> - goto found; >> - } >> - >> /* check FC0013 ID register; reg=00 val=a3 */ >> ret = rtl28xxu_ctrl_msg(adap->dev, &req_fc0013); >> if (ret == 0 && buf[0] == 0xa3) { >> @@ -640,6 +631,71 @@ >> goto unsupported; >> } >> >> + /* If it's a FC0012, we need to bring GPIO5/RESET >> + out of floating or it's not going to show up. >> + We set GPIO5 to an output, enable the output, then >> + reset the tuner by bringing GPIO5 high then low again. >> + >> + We're testing this last so that we don't accidentally >> + mess with other hardware that wouldn't like us messing >> + with whatever is connected to the rtl2832's GPIO5 >> + */ >> + >> + /* close demod I2C gate */ >> + ret = rtl28xxu_ctrl_msg(adap->dev, &req_gate_close); >> + if (ret) >> + goto err; >> + >> + /* Set GPIO5 to be an output */ >> + ret = rtl28xx_rd_reg(adap->dev, SYS_GPIO_DIR, &val); >> + if (ret) >> + goto err; >> + >> + val &= 0xdf; >> + ret = rtl28xx_wr_reg(adap->dev, SYS_GPIO_DIR, val); >> + if (ret) >> + goto err; >> + >> + /* enable as output GPIO5 */ >> + ret = rtl28xx_rd_reg(adap->dev, SYS_GPIO_OUT_EN, &val); >> + if (ret) >> + goto err; >> + >> + val |= 0x20; >> + ret = rtl28xx_wr_reg(adap->dev, SYS_GPIO_OUT_EN, val); >> + if (ret) >> + goto err; >> + >> + /* set GPIO5 high to reset fc0012 (if it exists) */ >> + ret = rtl28xx_rd_reg(adap->dev, SYS_GPIO_OUT_VAL, &val); >> + if (ret) >> + goto err; >> + >> + val |= 0x20; >> + ret = rtl28xx_wr_reg(adap->dev, SYS_GPIO_OUT_VAL, val); >> + if (ret) >> + goto err; >> + >> + /* bring GPIO5 low again after reset */ >> + val &= 0xdf; >> + ret = rtl28xx_wr_reg(adap->dev, SYS_GPIO_OUT_VAL, val); >> + if (ret) >> + goto err; >> + >> + /* re-open demod I2C gate */ >> + ret = rtl28xxu_ctrl_msg(adap->dev, &req_gate_open); >> + if (ret) >> + goto err; >> + >> + /* check FC0012 ID register; reg=00 val=a1 */ >> + ret = rtl28xxu_ctrl_msg(adap->dev, &req_fc0012); >> + if (ret == 0 && buf[0] == 0xa1) { >> + priv->tuner = TUNER_RTL2832_FC0012; >> + rtl2832_config = &rtl28xxu_rtl2832_fc0012_config; >> + info("%s: FC0012 tuner found", __func__); >> + goto found; >> + } >> + >> unsupported: >> /* close demod I2C gate */ >> ret = rtl28xxu_ctrl_msg(adap->dev, &req_gate_close); >> > > …sorry for the delay, > After applied patch no luck - in attach is dmesg for working original > Realtek driver(dvb_usb_rtl2832), and second one(dvb-usb-rtl28xxu) > rtl2832 part by Thomas with tuner issue, still not working. > Most intriguing is tuner get stucked by tuning(t-zapping)! > …after warm/unload/load/reboot of course ;) This is full set of logs. Tuner(fc0012) has no debug facility(parm), so nothing from there. modprobe.d/.conf: options dvb_core frontend_debug=1 debug=1 dvbdev_debug=1 options dvb_usb debug=511 options dvb_usb_rtl28xxu debug=1 options rtl2832 debug=1 Cheers, poma
usb 2-3: new high-speed USB device number 4 using ehci_hcd usb 2-3: New USB device found, idVendor=1f4d, idProduct=b803 usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-3: Product: RTL2838UHIDIR usb 2-3: Manufacturer: Realtek usb 2-3: SerialNumber: 00000041 rtl28xxu_probe: interface=0 check for warm bda 2831 check for warm 14aa 160 check for warm 14aa 161 something went very wrong, device was not found in current device list - let's see what comes next. check for warm ccd a9 check for warm 1f4d b803 dvb-usb: found a 'G-Tek Electronics Group Lifeview LV5TDLX DVB-T' in warm state. power control: 1 rtl2832u_power_ctrl: onoff=1 dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. all in all I will use 24576 bytes for streaming allocating buffer 0 buffer 0: ffff8800c05c5000 (dma: 3227275264) allocating buffer 1 buffer 1: ffff8800bddf0000 (dma: 3185508352) allocating buffer 2 buffer 2: ffff8800bde04000 (dma: 3185590272) allocating buffer 3 buffer 3: ffff8800bde84000 (dma: 3186114560) allocating buffer 4 buffer 4: ffff8800c3daa000 (dma: 3285884928) allocating buffer 5 buffer 5: ffff8800bddbc000 (dma: 3185295360) allocation successful DVB: registering new adapter (G-Tek Electronics Group Lifeview LV5TDLX DVB-T) DVB: register adapter0/demux0 @ minor: 0 (0x00) DVB: register adapter0/dvr0 @ minor: 1 (0x01) DVB: register adapter0/net0 @ minor: 2 (0x02) rtl2832u_frontend_attach: rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu: rtl2832u_frontend_attach: FC0012 tuner found rtl2832: rtl2832_attach dvb_register_frontend DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))... DVB: register adapter0/frontend0 @ minor: 3 (0x03) dvb_frontend_clear_cache() Clearing cache for delivery system 3 rtl2832u_tuner_attach: fc0012: Fitipower FC0012 successfully attached. Registered IR keymap rc-empty input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc1/input13 rc1: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc1 dvb-usb: schedule remote query interval to 400 msecs. power control: 0 rtl2832u_power_ctrl: onoff=0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully initialized and connected. rtl28xxu_probe: interface=1
dvb_frontend_open dvb_frontend_start dvb_frontend_thread dvb_frontend_ioctl (61) DVB: initialising adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))... power control: 1 rtl2832u_power_ctrl: onoff=1 rtl2832: rtl2832_init rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 current delivery system on cache: 3, V3 type: 0 dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=570000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 1d d8 01 cf function : dvb_dmxdev_filter_set start pid: 0x0064, feedtype: 1 setting pid (no): 100 0064 at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x00c8, feedtype: 1 setting pid (no): 200 00c8 at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x012c, feedtype: 1 setting pid (no): 300 012c at index 5 'on' function : dvb_dmxdev_filter_set start pid: 0x0190, feedtype: 1 setting pid (no): 400 0190 at index 6 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 11 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 01 c5 stop pid: 0x0064, feedtype: 1 setting pid (no): 100 0064 at index 3 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 03 c5 stop pid: 0x012c, feedtype: 1 setting pid (no): 300 012c at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 04 c5 stop pid: 0x0190, feedtype: 1 setting pid (no): 400 0190 at index 6 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 55 d8 01 cf stop pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 02 c3 stop pid: 0x00c8, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 512/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 200 00c8 at index 4 'off' dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=578000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 21 d8 04 cd function : dvb_dmxdev_filter_set start pid: 0x12ca, feedtype: 1 setting pid (no): 4810 12ca at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x12d4, feedtype: 1 setting pid (no): 4820 12d4 at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x0faa, feedtype: 1 setting pid (no): 4010 0faa at index 5 'on' function : dvb_dmxdev_filter_set start pid: 0x0fb4, feedtype: 1 setting pid (no): 4020 0fb4 at index 6 'on' function : dvb_dmxdev_filter_set start pid: 0x0fbe, feedtype: 1 setting pid (no): 4030 0fbe at index 7 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 14 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 12 c2 c3 stop pid: 0x12d4, feedtype: 1 setting pid (no): 4820 12d4 at index 4 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 rtl2832: rtl2832_read_status 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dvb_frontend_add_event dvb_frontend_swzigzag_update_delay 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 36 b1 c5 stop pid: 0x0faa, feedtype: 1 setting pid (no): 4010 0faa at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 3d 36 b2 c5 stop pid: 0x0fb4, feedtype: 1 setting pid (no): 4020 0fb4 at index 6 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 36 b3 c9 stop pid: 0x0fbe, feedtype: 1 setting pid (no): 4030 0fbe at index 7 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 12 c1 c5 stop pid: 0x12ca, feedtype: 1 setting pid (no): 4810 12ca at index 3 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 82 d8 04 d1 stop pid: 0x0011, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 1024/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 17 0011 at index 1 'off' dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=730000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 1d d8 02 cb function : dvb_dmxdev_filter_set start pid: 0x07da, feedtype: 1 setting pid (no): 2010 07da at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x07e4, feedtype: 1 setting pid (no): 2020 07e4 at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x07ee, feedtype: 1 setting pid (no): 2030 07ee at index 5 'on' function : dvb_dmxdev_filter_set start pid: 0x07f8, feedtype: 1 setting pid (no): 2040 07f8 at index 6 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 12 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 0d 00 15 c3 stop pid: 0x07da, feedtype: 1 setting pid (no): 2010 07da at index 3 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 0d 00 16 c3 stop pid: 0x07e4, feedtype: 1 setting pid (no): 2020 07e4 at index 4 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 17 c5 stop pid: 0x07ee, feedtype: 1 setting pid (no): 2030 07ee at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 18 c5 stop pid: 0x07f8, feedtype: 1 setting pid (no): 2040 07f8 at index 6 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 rtl2832: rtl2832_read_status 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dvb_frontend_add_event dvb_frontend_swzigzag_update_delay 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 56 d8 02 cb stop pid: 0x0011, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 1024/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 17 0011 at index 1 'off' dvb_frontend_release rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 rtl2832: rtl2832_sleep power control: 0 rtl2832u_power_ctrl: onoff=0
usb 2-3: USB disconnect, device number 4 state before exiting everything: 7 dvb_unregister_frontend dvb_frontend_stop rtl2832: rtl2832_release unregistering DVB part freeing URB no. 0. freeing URB no. 1. freeing URB no. 2. freeing URB no. 3. freeing URB no. 4. freeing URB no. 5. freeing buffer 5 freeing buffer 4 freeing buffer 3 freeing buffer 2 freeing buffer 1 freeing buffer 0 state should be zero now: 0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully deinitialized and disconnected. dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
rtl28xxu_module_exit: usbcore: deregistering interface driver dvb_usb_rtl28xxu dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. state before exiting everything: 7 dvb_unregister_frontend dvb_frontend_stop rtl2832: rtl2832_release unregistering DVB part freeing URB no. 0. freeing URB no. 1. freeing URB no. 2. freeing URB no. 3. freeing URB no. 4. freeing URB no. 5. freeing buffer 5 freeing buffer 4 freeing buffer 3 freeing buffer 2 freeing buffer 1 freeing buffer 0 state should be zero now: 0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully deinitialized and disconnected.
rtl28xxu_module_init: rtl28xxu_probe: interface=0 check for warm bda 2831 check for warm 14aa 160 check for warm 14aa 161 something went very wrong, device was not found in current device list - let's see what comes next. check for warm ccd a9 check for warm 1f4d b803 dvb-usb: found a 'G-Tek Electronics Group Lifeview LV5TDLX DVB-T' in warm state. power control: 1 rtl2832u_power_ctrl: onoff=1 dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. all in all I will use 24576 bytes for streaming allocating buffer 0 buffer 0: ffff8800b8c4b000 (dma: 3099897856) allocating buffer 1 buffer 1: ffff8800bdd96000 (dma: 3185139712) allocating buffer 2 buffer 2: ffff8800bde90000 (dma: 3186163712) allocating buffer 3 buffer 3: ffff8800b8c07000 (dma: 3099619328) allocating buffer 4 buffer 4: ffff8800bddaf000 (dma: 3185242112) allocating buffer 5 buffer 5: ffff8800bdc7a000 (dma: 3183976448) allocation successful DVB: registering new adapter (G-Tek Electronics Group Lifeview LV5TDLX DVB-T) DVB: register adapter0/demux0 @ minor: 0 (0x00) DVB: register adapter0/dvr0 @ minor: 1 (0x01) DVB: register adapter0/net0 @ minor: 2 (0x02) rtl2832u_frontend_attach: rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu: rtl2832u_frontend_attach: FC0012 tuner found rtl2832: rtl2832_attach dvb_register_frontend DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))... DVB: register adapter0/frontend0 @ minor: 3 (0x03) dvb_frontend_clear_cache() Clearing cache for delivery system 3 rtl2832u_tuner_attach: fc0012: Fitipower FC0012 successfully attached. Registered IR keymap rc-empty input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc0/input15 rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc0 dvb-usb: schedule remote query interval to 400 msecs. power control: 0 rtl2832u_power_ctrl: onoff=0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully initialized and connected. rtl28xxu_probe: interface=1 usbcore: registered new interface driver dvb_usb_rtl28xxu
dvb_frontend_open dvb_frontend_start dvb_frontend_thread dvb_frontend_ioctl (61) DVB: initialising adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))... power control: 1 rtl2832u_power_ctrl: onoff=1 rtl2832: rtl2832_init rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 current delivery system on cache: 3, V3 type: 0 dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=570000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 55 d8 01 cf stop pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 1d d8 01 cf function : dvb_dmxdev_filter_set start pid: 0x0064, feedtype: 1 setting pid (no): 100 0064 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x00c8, feedtype: 1 setting pid (no): 200 00c8 at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x012c, feedtype: 1 setting pid (no): 300 012c at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x0190, feedtype: 1 setting pid (no): 400 0190 at index 5 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 11 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 01 c5 stop pid: 0x0064, feedtype: 1 setting pid (no): 100 0064 at index 1 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 03 c5 stop pid: 0x012c, feedtype: 1 setting pid (no): 300 012c at index 4 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 04 c5 stop pid: 0x0190, feedtype: 1 setting pid (no): 400 0190 at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 rtl2832: rtl2832_read_status 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dvb_frontend_add_event dvb_frontend_swzigzag_update_delay 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 02 c3 stop pid: 0x00c8, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 512/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 200 00c8 at index 3 'off' dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=578000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 21 d8 04 cd function : dvb_dmxdev_filter_set start pid: 0x12ca, feedtype: 1 setting pid (no): 4810 12ca at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x12d4, feedtype: 1 setting pid (no): 4820 12d4 at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x0faa, feedtype: 1 setting pid (no): 4010 0faa at index 5 'on' function : dvb_dmxdev_filter_set start pid: 0x0fb4, feedtype: 1 setting pid (no): 4020 0fb4 at index 6 'on' function : dvb_dmxdev_filter_set start pid: 0x0fbe, feedtype: 1 setting pid (no): 4030 0fbe at index 7 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 14 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 12 c2 c3 stop pid: 0x12d4, feedtype: 1 setting pid (no): 4820 12d4 at index 4 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 36 b1 c5 stop pid: 0x0faa, feedtype: 1 setting pid (no): 4010 0faa at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 3d 36 b2 c5 stop pid: 0x0fb4, feedtype: 1 setting pid (no): 4020 0fb4 at index 6 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 36 b3 c9 stop pid: 0x0fbe, feedtype: 1 setting pid (no): 4030 0fbe at index 7 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 12 c1 c5 stop pid: 0x12ca, feedtype: 1 setting pid (no): 4810 12ca at index 3 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 rtl2832: rtl2832_read_status 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dvb_frontend_add_event dvb_frontend_swzigzag_update_delay 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 82 d8 04 d1 stop pid: 0x0011, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 1024/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 17 0011 at index 1 'off' dvb_frontend_ioctl (76) set_delivery_system() Using delivery system to 3 dtv_property_cache_sync() Preparing OFDM req dtv_property_legacy_params_sync() Preparing OFDM req rtl2832: rtl2832_get_tune_settings dvb_frontend_add_event dvb_frontend_swzigzag_autotune: drift:0 inversion:0 auto_step:0 auto_sub_step:0 started_auto_step:0 rtl2832: rtl2832_set_frontend: frequency=730000000 bandwidth_hz=8000000 inversion=0 rtl2832u_fc0012_tuner_callback cmd=0 arg=0 rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status dvb_frontend_ioctl (69) rtl2832: rtl2832_read_status function : dvb_dmxdev_filter_set start pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'on' submitting all URBs submitting URB no. 0 submitting URB no. 1 submitting URB no. 2 submitting URB no. 3 submitting URB no. 4 submitting URB no. 5 controlling pid parser start feeding rtl2832u_streaming_ctrl: onoff=1 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. 'bulk' urb completed. status: -32, length: 0/4096, pack_num: 0, errors: 0 urb completition error -32. function : dvb_dmxdev_filter_set start pid: 0x0011, feedtype: 1 setting pid (no): 17 0011 at index 1 'on' function : dvb_dmxdev_filter_set start pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'on' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 00 b0 1d d8 02 cb function : dvb_dmxdev_filter_set start pid: 0x07da, feedtype: 1 setting pid (no): 2010 07da at index 3 'on' function : dvb_dmxdev_filter_set start pid: 0x07e4, feedtype: 1 setting pid (no): 2020 07e4 at index 4 'on' function : dvb_dmxdev_filter_set start pid: 0x07ee, feedtype: 1 setting pid (no): 2030 07ee at index 5 'on' function : dvb_dmxdev_filter_set start pid: 0x07f8, feedtype: 1 setting pid (no): 2040 07f8 at index 6 'on' stop pid: 0x0000, feedtype: 1 setting pid (no): 0 0000 at index 0 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 40 f0 2d 31 12 c5 stop pid: 0x0010, feedtype: 1 setting pid (no): 16 0010 at index 2 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 0d 00 15 c3 stop pid: 0x07da, feedtype: 1 setting pid (no): 2010 07da at index 3 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 0d 00 16 c3 stop pid: 0x07e4, feedtype: 1 setting pid (no): 2020 07e4 at index 4 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 17 c5 stop pid: 0x07ee, feedtype: 1 setting pid (no): 2030 07ee at index 5 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 02 b0 2e 00 18 c5 stop pid: 0x07f8, feedtype: 1 setting pid (no): 2040 07f8 at index 6 'off' 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 rtl2832: rtl2832_read_status 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dvb_frontend_add_event dvb_frontend_swzigzag_update_delay 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 … 'bulk' urb completed. status: 0, length: 4096/4096, pack_num: 0, errors: 0 dmxdev: section callback 42 f0 56 d8 02 cb stop pid: 0x0011, feedtype: 1 stop feeding killing URB no. 0. 'bulk' urb completed. status: -2, length: 1024/4096, pack_num: 0, errors: 0 killing URB no. 1. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 2. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 3. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 4. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 killing URB no. 5. 'bulk' urb completed. status: -2, length: 0/4096, pack_num: 0, errors: 0 rtl2832u_streaming_ctrl: onoff=0 setting pid (no): 17 0011 at index 1 'off' dvb_frontend_release rtl2832: rtl2832_i2c_gate_ctrl: enable=1 rtl2832: rtl2832_i2c_gate_ctrl: enable=0 rtl2832: rtl2832_sleep power control: 0 rtl2832u_power_ctrl: onoff=0
rtl28xxu_module_exit: usbcore: deregistering interface driver dvb_usb_rtl28xxu dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. state before exiting everything: 7 dvb_unregister_frontend dvb_frontend_stop rtl2832: rtl2832_release unregistering DVB part freeing URB no. 0. freeing URB no. 1. freeing URB no. 2. freeing URB no. 3. freeing URB no. 4. freeing URB no. 5. freeing buffer 5 freeing buffer 4 freeing buffer 3 freeing buffer 2 freeing buffer 1 freeing buffer 0 state should be zero now: 0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully deinitialized and disconnected.
rtl28xxu_module_init: rtl28xxu_probe: interface=0 check for warm bda 2831 check for warm 14aa 160 check for warm 14aa 161 something went very wrong, device was not found in current device list - let's see what comes next. check for warm ccd a9 check for warm 1f4d b803 dvb-usb: found a 'G-Tek Electronics Group Lifeview LV5TDLX DVB-T' in warm state. power control: 1 rtl2832u_power_ctrl: onoff=1 dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. all in all I will use 24576 bytes for streaming allocating buffer 0 buffer 0: ffff8800bdef4000 (dma: 3186573312) allocating buffer 1 buffer 1: ffff8800bddd3000 (dma: 3185389568) allocating buffer 2 buffer 2: ffff8800bdd10000 (dma: 3184590848) allocating buffer 3 buffer 3: ffff8800bdeb1000 (dma: 3186298880) allocating buffer 4 buffer 4: ffff8800c06c9000 (dma: 3228340224) allocating buffer 5 buffer 5: ffff8800bdeed000 (dma: 3186544640) allocation successful DVB: registering new adapter (G-Tek Electronics Group Lifeview LV5TDLX DVB-T) DVB: register adapter0/demux0 @ minor: 0 (0x00) DVB: register adapter0/dvr0 @ minor: 1 (0x01) DVB: register adapter0/net0 @ minor: 2 (0x02) rtl2832u_frontend_attach: rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 rtl28xxu_ctrl_msg: failed=-32 No compatible tuner found dvb-usb: no frontend was attached by 'G-Tek Electronics Group Lifeview LV5TDLX DVB-T' Registered IR keymap rc-empty input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc0/input16 rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.1/usb2/2-3/rc/rc0 dvb-usb: schedule remote query interval to 400 msecs. power control: 0 rtl2832u_power_ctrl: onoff=0 dvb-usb: G-Tek Electronics Group Lifeview LV5TDLX DVB-T successfully initialized and connected. rtl28xxu_probe: interface=1 usbcore: registered new interface driver dvb_usb_rtl28xxu
< rtl28xxu: rtl2832u_frontend_attach: FC0012 tuner found < rtl2832: rtl2832_attach < dvb_register_frontend < DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))... < DVB: register adapter0/frontend0 @ minor: 3 (0x03) < dvb_frontend_clear_cache() Clearing cache for delivery system 3 < rtl2832u_tuner_attach: < fc0012: Fitipower FC0012 successfully attached. --- > No compatible tuner found > dvb-usb: no frontend was attached by 'G-Tek Electronics Group Lifeview LV5TDLX DVB-T'
