Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
... + analog parts.
Analog is not supported currently. Only DVB-T and DVB-C.
There seems to be still problems for locking DVB-C channels which have
strong signal. Attenuator helps. I think it is demodulator IF/RF AGC
issue. Lets fix it later. Patches are welcome.
Signed-off-by: Antti Palosaari <crope@xxxxxx>
---
drivers/media/video/em28xx/em28xx-cards.c | 28 +++++++++++++++
drivers/media/video/em28xx/em28xx-dvb.c | 52 +++++++++++++++++++++++++++++
drivers/media/video/em28xx/em28xx.h | 1 +
3 files changed, 81 insertions(+), 0 deletions(-)
diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index d5c9613..a65d479 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -364,6 +364,20 @@ static struct em28xx_reg_seq maxmedia_ub425_tc[] = {
{-1, -1, -1, -1},
};
+/* 2013:0251 PCTV QuatroStick nano (520e)
+ * GPIO_2: decoder reset, 0=active
+ * GPIO_4: decoder suspend, 0=active
+ * GPIO_6: demod reset, 0=active
+ * GPIO_7: LED, 1=active
+ */
+static struct em28xx_reg_seq pctv_520e[] = {
+ {EM2874_R80_GPIO, 0x10, 0xff, 100},
+ {EM2874_R80_GPIO, 0x14, 0xff, 100}, /* GPIO_2 = 1 */
+ {EM2874_R80_GPIO, 0x54, 0xff, 050}, /* GPIO_6 = 1 */
+ {EM2874_R80_GPIO, 0xd4, 0xff, 000}, /* GPIO_7 = 1 */
+ { -1, -1, -1, -1},
+};
+
/*
* Board definitions
*/
@@ -1930,6 +1944,18 @@ struct em28xx_board em28xx_boards[] = {
EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
+ /* 2013:0251 PCTV QuatroStick nano (520e)
+ * Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2 */
+ [EM2884_BOARD_PCTV_520E] = {
+ .name = "PCTV QuatroStick nano (520e)",
+ .tuner_type = TUNER_ABSENT,
+ .tuner_gpio = pctv_520e,
+ .has_dvb = 1,
+ .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
+ .i2c_speed = EM2874_I2C_SECONDARY_BUS_SELECT |
+ EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
+ },
};
const unsigned int em28xx_bcount = ARRAY_SIZE(em28xx_boards);
@@ -2083,6 +2109,8 @@ struct usb_device_id em28xx_id_table[] = {
.driver_info = EM2860_BOARD_EASYCAP },
{ USB_DEVICE(0x1b80, 0xe425),
.driver_info = EM2874_BOARD_MAXMEDIA_UB425_TC },
+ { USB_DEVICE(0x2013, 0x0251),
+ .driver_info = EM2884_BOARD_PCTV_520E },
{ },
};
MODULE_DEVICE_TABLE(usb, em28xx_id_table);
diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c
index 0b3e301..398d713 100644
--- a/drivers/media/video/em28xx/em28xx-dvb.c
+++ b/drivers/media/video/em28xx/em28xx-dvb.c
@@ -331,6 +331,13 @@ struct drxk_config maxmedia_ub425_tc_drxk = {
.no_i2c_bridge = 1,
};
+struct drxk_config pctv_520e_drxk = {
+ .adr = 0x29,
+ .single_master = 1,
+ .microcode_name = "dvb-demod-drxk-pctv.fw",
+ .chunk_size = 58,
+};
+
static int drxk_gate_ctrl(struct dvb_frontend *fe, int enable)
{
struct em28xx_dvb *dvb = fe->sec_priv;
@@ -464,6 +471,33 @@ static void terratec_h5_init(struct em28xx *dev)
em28xx_gpio_set(dev, terratec_h5_end);
};
+static void pctv_520e_init(struct em28xx *dev)
+{
+ /*
+ * Init TDA8295(?) analog demodulator. Looks like I2C traffic to
+ * digital demodulator and tuner are routed via TDA8295.
+ */
+ int i;
+ struct {
+ unsigned char r[4];
+ int len;
+ } regs[] = {
+ {{ 0x06, 0x02, 0x00, 0x31 }, 4},
+ {{ 0x01, 0x02 }, 2},
+ {{ 0x01, 0x02, 0x00, 0xc6 }, 4},
+ {{ 0x01, 0x00 }, 2},
+ {{ 0x01, 0x00, 0xff, 0xaf }, 4},
+ {{ 0x01, 0x00, 0x03, 0xa0 }, 4},
+ {{ 0x01, 0x00 }, 2},
+ {{ 0x01, 0x00, 0x73, 0xaf }, 4},
+ };
+
+ dev->i2c_client.addr = 0x82 >> 1; /* 0x41 */
+
+ for (i = 0; i < ARRAY_SIZE(regs); i++)
+ i2c_master_send(&dev->i2c_client, regs[i].r, regs[i].len);
+};
+
static int em28xx_mt352_terratec_xs_init(struct dvb_frontend *fe)
{
/* Values extracted from a USB trace of the Terratec Windows driver */
@@ -965,6 +999,24 @@ static int em28xx_dvb_init(struct em28xx *dev)
"driver version\n");
break;
+ case EM2884_BOARD_PCTV_520E:
+ pctv_520e_init(dev);
+
+ /* attach demodulator */
+ dvb->fe[0] = dvb_attach(drxk_attach, &pctv_520e_drxk,
+ &dev->i2c_adap);
+
+ if (dvb->fe[0]) {
+ /* attach tuner */
+ if (!dvb_attach(tda18271_attach, dvb->fe[0], 0x60,
+ &dev->i2c_adap,
+ &em28xx_cxd2820r_tda18271_config)) {
+ dvb_frontend_detach(dvb->fe[0]);
+ result = -EINVAL;
+ goto out_free;
+ }
+ }
+ break;
default:
em28xx_errdev("/2: The frontend of your DVB/ATSC card"
" isn't supported yet\n");
diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h
index 59cdfa6..4b60327 100644
--- a/drivers/media/video/em28xx/em28xx.h
+++ b/drivers/media/video/em28xx/em28xx.h
@@ -126,6 +126,7 @@
#define EM2884_BOARD_CINERGY_HTC_STICK 82
#define EM2860_BOARD_HT_VIDBOX_NW03 83
#define EM2874_BOARD_MAXMEDIA_UB425_TC 84
+#define EM2884_BOARD_PCTV_520E 85
/* Limits minimum and default number of buffers */
#define EM28XX_MIN_BUF 4
--
1.7.7.6
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
