On 12/07/11 15:54, Mauro Carvalho Chehab wrote:
lin-tv ~ # lsusb | grep "Bus 002"
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 008: ID 2040:1605 Hauppauge
There's nothing at the DVB core returning -ENOSPC.
Try to add just one line to a channels file, like this one:
C 602000000 6900000 NONE QAM256
(this is the transponder that failed with w_scan. You could also use one
of the transponders where you got a pid timeout with scan)
Then call scan with this file, using strace:
$ strace -e ioctl dvbscan channelfile
This would allow to see what ioctl returned -ENOSPC (error -28).
Regards,
Mauro
Mauro,
I made a small script to check if the w_scan results are consistent:
#!/bin/bash
for i in `seq 1 20`;
do
w_scan -fc -c NO 1>> scan$i.log 2>> scan$i.log
done
And I get outputs like this (the timing numbers differs of course
somewhat between different runs):
<snip>
586000: sr6900 (time: 10:21) sr6875 (time: 10:23)
594000: sr6900 (time: 10:26) sr6875 (time: 10:28)
602000: sr6900 (time: 10:31) (time: 10:32) signal ok:
QAM_256 f = 602000 kHz S6900C999
Info: NIT(actual) filter timeout
610000: sr6900 (time: 10:44) sr6875 (time: 10:47)
618000: sr6900 (time: 10:49) sr6875 (time: 10:52)
626000: sr6900 (time: 10:54) sr6875 (time: 10:57)
<snip>
Then I did the test that you suggested:
lin-tv ~ # strace -e ioctl dvbscan -fc test_channel_file
scanning test_channel_file
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ioctl(3, FE_GET_INFO, 0x60b180) = 0
initial transponder 602000000 6900000 0 5
>>> tune to: 602000000:INVERSION_AUTO:6900000:FEC_NONE:QAM_256
ioctl(3, FE_SET_FRONTEND, 0x7fff0581fb20) = 0
ioctl(3, FE_READ_STATUS, 0x7fff0581fb4c) = 0
ioctl(3, FE_READ_STATUS, 0x7fff0581fb4c) = 0
ioctl(4, DMX_SET_FILTER, 0x7fff0581e930) = 0
ioctl(5, DMX_SET_FILTER, 0x7fff0581e930) = 0
ioctl(6, DMX_SET_FILTER, 0x7fff0581e930) = 0
WARNING: filter timeout pid 0x0011
ioctl(5, DMX_STOP, 0x23) = 0
WARNING: filter timeout pid 0x0000
ioctl(4, DMX_STOP, 0x23) = 0
WARNING: filter timeout pid 0x0010
ioctl(6, DMX_STOP, 0x23) = 0
dumping lists (0 services)
Done.
I did not get the:
602000: sr6900 (time: 10:32) (time: 10:33) signal ok:
QAM_256 f = 602000 kHz S6900C999
start_filter:1415: ERROR: ioctl DMX_SET_FILTER failed: 28 No space left
on device
Info: NIT(actual) filter timeout
that I got before. The changes I made from before was 1) I unmounted the
USB disk and 2) I rebuild the xc5000 module where I removed the
mutex_lock(&xc5000_list_mutex);
and
mutex_unlock(&xc5000_list_mutex);
lines according to the discussion in the " ... em28xx: initial support
for HAUPPAUGE HVR-930C again" thread.
/Fredrik
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
