Hi all, I'm not entirely sure if this is the correct list, but I compiled the latest 3.2 RC3 kernel to get native support of my S2-3600 tuner (s2-liplianin seems to cause trouble with my other tuner). I enabled the PCTV452e module in the kernel and the device detects ok; [ 12.075239] dvb-usb: found a 'Technotrend TT Connect S2-3600' in warm state. [ 12.076620] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 12.080767] dvb-usb: MAC address: 00:d0:5c:64:54:95 [ 12.759115] dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware [ 13.298383] dvb-usb: Technotrend TT Connect S2-3600 successfully initialized and connected. [ 13.464394] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw' [ 14.180319] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state. [ 14.180429] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 15.356117] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected. [ 15.356832] usbcore: registered new interface driver dvb_usb_dib0700 But when I try to make any tuning with the device I get no picture and the following get put to syslog; Dec 2 01:01:26 MicroServer kernel: [ 1535.331468] dvb-usb: could not submit URB no. 0 - get them all back Dec 2 01:01:26 MicroServer kernel: [ 1535.372388] pctv452e: I2C error -121; AA 97 CC 00 01 -> 55 97 CC 00 00. Dec 2 01:01:26 MicroServer kernel: [ 1535.385003] pctv452e: I2C error -121; AA AE CC 00 01 -> 55 AE CC 00 00. Dec 2 01:01:26 MicroServer kernel: [ 1535.444992] pctv452e: I2C error -121; AA C9 CC 00 01 -> 55 C9 CC 00 00. Dec 2 01:01:46 MicroServer kernel: [ 1555.665248] dvb-usb: could not submit URB no. 0 - get them all back Dec 2 01:01:46 MicroServer kernel: [ 1555.708805] pctv452e: I2C error -121; AA 2E CC 00 01 -> 55 2E CC 00 00. Dec 2 01:01:46 MicroServer kernel: [ 1555.722046] pctv452e: I2C error -121; AA 45 CC 00 01 -> 55 45 CC 00 00. Dec 2 01:01:46 MicroServer kernel: [ 1555.784543] pctv452e: I2C error -121; AA 60 CC 00 01 -> 55 60 CC 00 00. The 'URB' errors appear each time the card moves to a new transponder, the I2C errors appear to be when the card is attempting to lock a channel within the current transponder. Does anyone have any thoughts on what might be causing this ? - I've had a search around but can't really find the problem mentioned anywhere... the device works fine under the latest liplianin drivers. Many Thanks Neil -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
