This is an updated version of the unicable patch by Thomas Schloeter
for linux 3.1.
The patch is an addition to the dvb_frontend code, that adds fully
transparent support for SCR to arbitrary applications that use the
DVB API.
I know that this patch has been rejected, because unicable support
can be implemented in userspace, too. However I like it anyway,
because there is a lot of software without unicable support out
there. I'm just sending it, because I think it could be usefull
for others.
DVB satellite channel routing (aka "SCR", "Unicable", "EN50494") is
a standard, where all satellite tuners share the sam cable and each of
them has a fixed intermediate frequency it is supposed to tune to.
Zapping is done by sending a special DiSEqC message while SEC voltage
is temporarily pulled from 14 to 18 volts. This message includes the
tuner's ID from 0 to 7, the frequency, band and polarisation to tune
to as well as one out of two satellite positions.
By default SCR support is disabled and has to be enabled explicitly
via an ioctl command. At the same time you set the tuner's ID, the
frequency and other parameters. Thomas developed an utility
(dvb-scr-setup) to accomplish this task. It can be used unmodified.
I'm using this patch successfully with a DUR-LINE UK 101 unicable LNB.
Regards,
Christian
---
drivers/media/dvb/dvb-core/dvb_frontend.c | 186 +++++++++++++++++++++++++++-
include/linux/dvb/frontend.h | 20 +++
2 files changed, 199 insertions(+), 7 deletions(-)
diff --git a/drivers/media/dvb/dvb-core/dvb_frontend.c b/drivers/media/dvb/dvb-core/dvb_frontend.c
index efe9c30..62316be 100644
--- a/drivers/media/dvb/dvb-core/dvb_frontend.c
+++ b/drivers/media/dvb/dvb-core/dvb_frontend.c
@@ -9,6 +9,8 @@
*
* Copyright (C) 2004 Andrew de Quincey (tuning thread cleanup)
*
+ * Copyright (C) 2011 Thomas Schloeter (satellite channel routing)
+ *
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
@@ -50,6 +52,8 @@ static int dvb_override_tune_delay;
static int dvb_powerdown_on_sleep = 1;
static int dvb_mfe_wait_time = 5;
+int scr_send_tune_cmd(struct dvb_frontend*);
+
module_param_named(frontend_debug, dvb_frontend_debug, int, 0644);
MODULE_PARM_DESC(frontend_debug, "Turn on/off frontend core debugging (default:off).");
module_param(dvb_shutdown_timeout, int, 0644);
@@ -122,6 +126,10 @@ struct dvb_frontend_private {
int tone;
int voltage;
+ /* satellite channel routing */
+ struct dvb_scr_params dvbscr;
+ __u32 frequency_orig;
+
/* swzigzag values */
unsigned int state;
unsigned int bending;
@@ -1027,7 +1035,12 @@ static void dtv_property_cache_sync(struct dvb_frontend *fe,
struct dtv_frontend_properties *c,
const struct dvb_frontend_parameters *p)
{
- c->frequency = p->frequency;
+ struct dvb_frontend_private *fepriv = fe->frontend_priv;
+
+ if (fepriv->dvbscr.scr_enable == SCR_ON)
+ c->frequency = fepriv->frequency_orig;
+ else
+ c->frequency = p->frequency;
c->inversion = p->inversion;
switch (fe->ops.info.type) {
@@ -1081,6 +1094,7 @@ static void dtv_property_legacy_params_sync(struct dvb_frontend *fe)
struct dvb_frontend_private *fepriv = fe->frontend_priv;
struct dvb_frontend_parameters *p = &fepriv->parameters_in;
+ fepriv->frequency_orig = c->frequency;
p->frequency = c->frequency;
p->inversion = c->inversion;
@@ -1129,6 +1143,7 @@ static void dtv_property_adv_params_sync(struct dvb_frontend *fe)
struct dvb_frontend_private *fepriv = fe->frontend_priv;
struct dvb_frontend_parameters *p = &fepriv->parameters_in;
+ fepriv->frequency_orig = c->frequency;
p->frequency = c->frequency;
p->inversion = c->inversion;
@@ -1354,10 +1369,15 @@ static int dtv_property_process_set(struct dvb_frontend *fe,
dtv_property_dump(tvp);
/* Allow the frontend to validate incoming properties */
- if (fe->ops.set_property) {
- r = fe->ops.set_property(fe, tvp);
- if (r < 0)
- return r;
+ if ((fepriv->dvbscr.scr_enable != SCR_ON) ||
+ (tvp->cmd != DTV_FREQUENCY) ||
+ (tvp->cmd != DTV_VOLTAGE) ||
+ (tvp->cmd != DTV_TONE)) {
+ if (fe->ops.set_property) {
+ r = fe->ops.set_property(fe, tvp);
+ if (r < 0)
+ return r;
+ }
}
switch(tvp->cmd) {
@@ -1631,6 +1651,7 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
struct dvb_frontend *fe = dvbdev->priv;
struct dvb_frontend_private *fepriv = fe->frontend_priv;
int cb_err, err = -EOPNOTSUPP;
+ u32 fe_freq_min, fe_freq_max;
if (fe->dvb->fe_ioctl_override) {
cb_err = fe->dvb->fe_ioctl_override(fe, cmd, parg,
@@ -1702,6 +1723,11 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
break;
case FE_DISEQC_SEND_MASTER_CMD:
+ if (fepriv->dvbscr.scr_enable == SCR_ON) {
+ dprintk("DVB: %s: Operation not available when SCR enabled\n", __FUNCTION__);
+ err = 0;
+ break;
+ }
if (fe->ops.diseqc_send_master_cmd) {
err = fe->ops.diseqc_send_master_cmd(fe, (struct dvb_diseqc_master_cmd*) parg);
fepriv->state = FESTATE_DISEQC;
@@ -1710,6 +1736,11 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
break;
case FE_DISEQC_SEND_BURST:
+ if (fepriv->dvbscr.scr_enable == SCR_ON) {
+ dprintk("DVB: %s: Operation not available when SCR enabled\n", __FUNCTION__);
+ err = 0;
+ break;
+ }
if (fe->ops.diseqc_send_burst) {
err = fe->ops.diseqc_send_burst(fe, (fe_sec_mini_cmd_t) parg);
fepriv->state = FESTATE_DISEQC;
@@ -1717,9 +1748,65 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
}
break;
+ case FE_SET_SCR: {
+ struct dtv_frontend_properties *c = &fe->dtv_property_cache;
+
+ if (fe->ops.info.type != FE_QPSK) {
+ dprintk("DVB: %s: SCR is supported on QPSK frontends only!\n", __FUNCTION__);
+ err = -EINVAL;
+ break;
+ }
+ fepriv->dvbscr.scr_enable = ((struct dvb_scr_params *) parg)->scr_enable;
+ fepriv->dvbscr.scr_id = ((struct dvb_scr_params *) parg)->scr_id;
+ fepriv->dvbscr.scr_position = ((struct dvb_scr_params *) parg)->scr_position;
+ fepriv->dvbscr.scr_frequency = ((struct dvb_scr_params *) parg)->scr_frequency;
+ err = 0;
+ if ((fepriv->dvbscr.scr_enable != SCR_ON) && (fepriv->dvbscr.scr_enable != SCR_OFF)) {
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ err = -EINVAL;
+ dprintk("DVB: %s: Invalid value for SCR_ON in ioctl\n", __FUNCTION__);
+ }
+ dvb_frontend_get_frequency_limits(fe, &fe_freq_min, &fe_freq_max);
+ if ((fepriv->dvbscr.scr_frequency < fe_freq_min / 1000) || (fepriv->dvbscr.scr_frequency > fe_freq_max / 1000)) {
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ fepriv->dvbscr.scr_frequency = 1400;
+ err = -EINVAL;
+ dprintk("DVB: %s: Invalid value for SCR_FREQ in ioctl\n", __FUNCTION__);
+ }
+ if ((fepriv->dvbscr.scr_position != SCR_POS_A) && (fepriv->dvbscr.scr_position != SCR_POS_B)) {
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ fepriv->dvbscr.scr_position = SCR_POS_A;
+ err = -EINVAL;
+ dprintk("DVB: %s: Invalid value for SCR_POSITION in ioctl\n", __FUNCTION__);
+ }
+ if (fepriv->dvbscr.scr_id > 7) {
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ fepriv->dvbscr.scr_id = 0;
+ err = -EINVAL;
+ dprintk("DVB: %s: Invalid value for SCR_ID in ioctl\n", __FUNCTION__);
+ }
+ if (fe->ops.set_voltage)
+ fe->ops.set_voltage(fe, SEC_VOLTAGE_13);
+ else {
+ dprintk("DVB: %s: Set Voltage not supported. SCR not possible.\n", __FUNCTION__);
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ }
+ if (fe->ops.set_tone)
+ fe->ops.set_tone(fe, SEC_TONE_OFF);
+ else {
+ dprintk("DVB: %s: Set Tone not supported. SCR not possible.\n", __FUNCTION__);
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ }
+ dtv_property_cache_sync(fe, c, &fepriv->parameters_in);
+ break;
+ }
+
case FE_SET_TONE:
if (fe->ops.set_tone) {
- err = fe->ops.set_tone(fe, (fe_sec_tone_mode_t) parg);
+ if (fepriv->dvbscr.scr_enable == SCR_ON)
+ err = fe->ops.set_tone(fe, SEC_TONE_OFF);
+ else
+ err = fe->ops.set_tone(fe, (fe_sec_tone_mode_t) parg);
fepriv->tone = (fe_sec_tone_mode_t) parg;
fepriv->state = FESTATE_DISEQC;
fepriv->status = 0;
@@ -1728,7 +1815,10 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
case FE_SET_VOLTAGE:
if (fe->ops.set_voltage) {
- err = fe->ops.set_voltage(fe, (fe_sec_voltage_t) parg);
+ if (fepriv->dvbscr.scr_enable == SCR_ON)
+ err = fe->ops.set_voltage(fe, SEC_VOLTAGE_13);
+ else
+ err = fe->ops.set_voltage(fe, (fe_sec_voltage_t) parg);
fepriv->voltage = (fe_sec_voltage_t) parg;
fepriv->state = FESTATE_DISEQC;
fepriv->status = 0;
@@ -1736,6 +1826,11 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
break;
case FE_DISHNETWORK_SEND_LEGACY_CMD:
+ if (fepriv->dvbscr.scr_enable == SCR_ON) {
+ dprintk("DVB: %s: Operation not available when SCR enabled\n", __FUNCTION__);
+ err = 0;
+ break;
+ }
if (fe->ops.dishnetwork_send_legacy_command) {
err = fe->ops.dishnetwork_send_legacy_command(fe, (unsigned long) parg);
fepriv->state = FESTATE_DISEQC;
@@ -1827,6 +1922,10 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
dtv_property_cache_sync(fe, c, &fepriv->parameters_in);
}
+ /* intercept tuning info and replace with SCR parameters */
+ if (fepriv->dvbscr.scr_enable == SCR_ON)
+ scr_send_tune_cmd(fe);
+
memset(&fetunesettings, 0, sizeof(struct dvb_frontend_tune_settings));
memcpy(&fetunesettings.parameters, parg,
sizeof (struct dvb_frontend_parameters));
@@ -1899,6 +1998,10 @@ static int dvb_frontend_ioctl_legacy(struct file *file,
if (fe->ops.get_frontend) {
err = fe->ops.get_frontend(fe, &fepriv->parameters_out);
memcpy(parg, &fepriv->parameters_out, sizeof(struct dvb_frontend_parameters));
+ if (fepriv->dvbscr.scr_enable == SCR_ON) {
+ ((struct dvb_frontend_parameters*) parg)->frequency =
+ fepriv->frequency_orig;
+ }
}
break;
@@ -2098,6 +2201,12 @@ int dvb_register_frontend(struct dvb_adapter* dvb,
fe->dvb = dvb;
fepriv->inversion = INVERSION_OFF;
+ /* initialize SCR parameters */
+ fepriv->dvbscr.scr_enable = SCR_OFF;
+ fepriv->dvbscr.scr_id = 0;
+ fepriv->dvbscr.scr_frequency = 1400;
+ fepriv->dvbscr.scr_position = SCR_POS_A;
+
printk ("DVB: registering adapter %i frontend %i (%s)...\n",
fe->dvb->num,
fe->id,
@@ -2171,3 +2280,66 @@ void dvb_frontend_detach(struct dvb_frontend* fe)
}
#endif
EXPORT_SYMBOL(dvb_frontend_detach);
+
+int scr_send_tune_cmd(struct dvb_frontend * fe) {
+ struct dvb_frontend_private *fepriv = fe->frontend_priv;
+ int err = 0;
+ struct timeval waketime;
+ struct dvb_diseqc_master_cmd tunecmd;
+ uint8_t channel_byte_1, channel_byte_2;
+ uint16_t t;
+
+ dprintk ("DVB: Tuning to %u, %s, %s using SCR. ID=%u, POS=%s, FREQ=%u\n",
+ fepriv->parameters_in.frequency,
+ ((fepriv->voltage == SEC_VOLTAGE_18) ? "H" :
+ ((fepriv->voltage == SEC_VOLTAGE_13) ? "V" : "?")),
+ ((fepriv->tone == SEC_TONE_ON) ? "HiBand" : "LoBand"),
+ fepriv->dvbscr.scr_id,
+ ((fepriv->dvbscr.scr_position == SCR_POS_A) ? "A" : "B"),
+ fepriv->dvbscr.scr_frequency);
+
+ if (fepriv->dvbscr.scr_id > 7) {
+ dprintk ("DVB: %s - wrong SCR ID\n", __FUNCTION__);
+ fepriv->dvbscr.scr_id = 0;
+ }
+
+ channel_byte_1 = (uint8_t) (fepriv->dvbscr.scr_id << 5);
+
+ if (fepriv->dvbscr.scr_position != SCR_POS_A)
+ channel_byte_1 |= (1 << 4);
+
+ if (fepriv->voltage == SEC_VOLTAGE_18) /* horizontal*/
+ channel_byte_1 |= (1 << 3);
+
+ if (fepriv->tone == SEC_TONE_ON) /* high band*/
+ channel_byte_1 |= (1 << 2);
+
+ if (fepriv->frequency_orig == 0) {
+ dprintk ("DVB: %s - invalid SCR tuning\n", __FUNCTION__);
+ }
+
+ t = (uint16_t) ((((fepriv->parameters_in.frequency / 1000) + fepriv->dvbscr.scr_frequency + 2) / 4) - 350);
+ channel_byte_1 |= (((uint8_t) (t >> 8)) & 0x03);
+ channel_byte_2 = (uint8_t) (t & 0x00FF);
+
+ fepriv->frequency_orig = fepriv->parameters_in.frequency;
+ fepriv->parameters_in.frequency = (uint32_t) ((t + 350) * 4) * 1000 - fepriv->frequency_orig;
+
+ // Send DiSEqC code E0 10 5A channel_byte_1 channel_byte_2
+ tunecmd.msg_len = 5;
+ tunecmd.msg[0] = 0xE0;
+ tunecmd.msg[1] = 0x10;
+ tunecmd.msg[2] = 0x5A;
+ tunecmd.msg[3] = channel_byte_1;
+ tunecmd.msg[4] = channel_byte_2;
+
+ do_gettimeofday(&waketime);
+ if ((err = fe->ops.set_voltage(fe, SEC_VOLTAGE_18)) != 0) return err;
+ dvb_frontend_sleep_until(&waketime, 10000);
+ if ((err = fe->ops.diseqc_send_master_cmd(fe, &tunecmd)) != 0) return err;
+ do_gettimeofday(&waketime);
+ dvb_frontend_sleep_until(&waketime, 10000);
+ if ((err = fe->ops.set_voltage(fe, SEC_VOLTAGE_13)) != 0) return err;
+
+ return 0;
+}
diff --git a/include/linux/dvb/frontend.h b/include/linux/dvb/frontend.h
index 36a3ed6..570b3bd 100644
--- a/include/linux/dvb/frontend.h
+++ b/include/linux/dvb/frontend.h
@@ -212,6 +212,23 @@ typedef enum fe_hierarchy {
HIERARCHY_AUTO
} fe_hierarchy_t;
+/* satellite channel routing */
+typedef enum scr_status {
+ SCR_OFF,
+ SCR_ON
+} scr_status_t;
+
+typedef enum scr_positions {
+ SCR_POS_A,
+ SCR_POS_B
+} scr_position_t;
+
+struct dvb_scr_params {
+ scr_status_t scr_enable; /* enable or disable SCR */
+ __u8 scr_id; /* internal SCR id */
+ scr_position_t scr_position; /* SCR satellite position (A or B) */
+ __u32 scr_frequency; /* SCR frequency we tune to */
+};
struct dvb_qpsk_parameters {
__u32 symbol_rate; /* symbol rate in Symbols per second */
@@ -423,4 +440,7 @@ struct dtv_properties {
#define FE_DISHNETWORK_SEND_LEGACY_CMD _IO('o', 80) /* unsigned int */
+/* satellite channel routing */
+#define FE_SET_SCR _IOW('o', 120, struct dvb_scr_params)
+
#endif /*_DVBFRONTEND_H_*/
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
