On Sábado, 23 de Julio de 2011 19:47:27 Antti Palosaari escribió:
> On 07/23/2011 06:41 PM, Jose Alberto Reguero wrote:
> > On Sábado, 23 de Julio de 2011 12:37:53 Antti Palosaari escribió:
> >> On 07/23/2011 01:21 PM, Jose Alberto Reguero wrote:
> >>> On Sábado, 23 de Julio de 2011 11:42:58 Antti Palosaari escribió:
> >>>> On 07/23/2011 11:26 AM, Jose Alberto Reguero wrote:
> >>>>> The problem is in i2c read in tda827x_probe_version. Without the fix
> >>>>> sometimes, when changing the code the tuner is detected as tda827xo
> >>>>> instead of tda827xa. That is because the variable where i2c read
> >>>>> should store the value is initialized, and sometimes it works.
> >>>>
> >>>> struct i2c_msg msg = { .addr = priv->i2c_addr, .flags = I2C_M_RD,
> >>>>
> >>>> .buf =&data, .len = 1 };
> >>>>
> >>>> rc = tuner_transfer(fe,&msg, 1);
> >>>>
> >>>> :-( Could you read what I write. It is a little bit annoying to find
> >>>> :out
> >>>>
> >>>> everything for you. You just answer every time something like it does
> >>>> not work and I should always find out what's problem.
> >>>>
> >>>> As I pointed out read will never work since I2C adapter supports only
> >>>> read done in WRITE+READ combination. Driver uses read which is single
> >>>> READ without write.
> >>>>
> >>>> You should implement new read. You can look example from af9015 or
> >>>> other drivers using tda827x
> >>>>
> >>>> This have been never worked thus I Cc Guy Martin who have added DVB-C
> >>>> support for that device.
> >>>>
> >>>>
> >>>> regards
> >>>> Antti
> >>>
> >>> I don't understand you. I think that you don' see the fix, but the old
> >>> code. Old code:
> >>>
> >>> read = i+1< num&& (msg[i+1].flags& I2C_M_RD);
> >>>
> >>> Fix:
> >>>
> >>> read1 = i+1< num&& (msg[i+1].flags& I2C_M_RD); for the tda10023
> >>> and tda10048 read2 = msg[i].flags& I2C_M_RD; for the tda827x
> >>>
> >>> Jose Alberto
> >>
> >> First of all I must apologize of blaming you about that I2C adapter,
> >> sorry, I should going to shame now. It was me who doesn't read your
> >> changes as should :/
> >>
> >> Your changes are logically OK and implements correctly single reading as
> >> needed. Some comments still;
> >> * consider renaming read1 and read2 for example write_read and read
> >> * obuf[1] contains WRITE len. your code sets that now as READ len.
> >> Probably it should be 0 always in single write since no bytes written.
> >> * remove useless checks from end of the "if (foo) if (foo)";
> >> if (read1 || read2) {
> >>
> >> if (read1) {
> >>
> >> [...]
> >>
> >> } else if (read2)
> >>
> >> If you store some variables at the beginning, olen, ilen, obuf, ibuf,
> >> you can increase i++ for write+read and rest of the code in function can
> >> be same (no more if read or write + read). But maybe it is safe to keep
> >> closer original than change such much.
> >>
> >>
> >> regards
> >> Antti
> >
> > There are a second i2c read, but less important.It is in:
> >
> > tda827xa_set_params
> >
> > ............
> >
> > buf[0] = 0xa0;
> > buf[1] = 0x40;
> > msg.len = 2;
> > rc = tuner_transfer(fe,&msg, 1);
> > if (rc< 0)
> >
> > goto err;
> >
> > msleep(11);
> > msg.flags = I2C_M_RD;
> > rc = tuner_transfer(fe,&msg, 1);
> > if (rc< 0)
> >
> > goto err;
> >
> > msg.flags = 0;
> >
> > buf[1]>>= 4;
> >
> > ............
> > I supposed that buf[0] is the register to read and they read the value in
> > buf[1]. The code now seem to work ok but perhaps is wrong.
>
> This one is as translated to "normal" C we usually use;
> write_reg(0xa0, 0x40); // write one reg
> read_regs(2); // read 2 regs
>
> example from the sniff
> AA B0 31 05 C2 02 00 A0 40 ª°1.Â.. @
> 55 B0 31 03 C2 02 00 4A 44 08 00 00 00 71 AC EC U°1.Â..JD....q¬ì
> AA B1 31 05 C2 02 00 30 11 ª±1.Â..0.
> 55 B1 31 03 C2 02 00 4A 44 08 00 00 00 71 AC EC U±1.Â..JD....q¬ì
>
>
> AA USB direction to device
> B1 USB msg seq
> 31 USB cmd
> 05 USB data len (4+5=9, 4=hdr len, 5=data len, 9=total)
> C2 I2C addr (addr << 1)
> 02 I2C write len
> 00 I2C read len
> 30 I2C data [0]
> 11 I2C data [1]
>
> So it seems actually to write 30 11 and then read 4a 44 as reply. But if
> you read driver code it does not write "30 11" instead just reads. Maybe
> buggy I2C adap implementation or buggy tuner driver (Linux driver or
> driver where sniff taken). Try to read without write and with write and
> compare if there is any difference.
>
>
> regards
> Antti
Read without write work as with write. Attached updated patch.
Signed-off-by: Jose Alberto Reguero <jareguero@xxxxxxxxxxxxxx>
Jose Alberto
diff -ur linux/drivers/media/dvb/dvb-usb/ttusb2.c linux.new/drivers/media/dvb/dvb-usb/ttusb2.c
--- linux/drivers/media/dvb/dvb-usb/ttusb2.c 2011-01-10 16:24:45.000000000 +0100
+++ linux.new/drivers/media/dvb/dvb-usb/ttusb2.c 2011-07-23 23:12:29.341385243 +0200
@@ -30,6 +30,7 @@
#include "tda826x.h"
#include "tda10086.h"
#include "tda1002x.h"
+#include "tda10048.h"
#include "tda827x.h"
#include "lnbp21.h"
@@ -82,7 +83,7 @@
{
struct dvb_usb_device *d = i2c_get_adapdata(adap);
static u8 obuf[60], ibuf[60];
- int i,read;
+ int i, write_read, read;
if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
return -EAGAIN;
@@ -91,28 +92,35 @@
warn("more than 2 i2c messages at a time is not handled yet. TODO.");
for (i = 0; i < num; i++) {
- read = i+1 < num && (msg[i+1].flags & I2C_M_RD);
+ write_read = i+1 < num && (msg[i+1].flags & I2C_M_RD);
+ read = msg[i].flags & I2C_M_RD;
- obuf[0] = (msg[i].addr << 1) | read;
- obuf[1] = msg[i].len;
+ obuf[0] = (msg[i].addr << 1) | (write_read | read);
+ if (read)
+ obuf[1] = 0;
+ else
+ obuf[1] = msg[i].len;
/* read request */
- if (read)
+ if (write_read)
obuf[2] = msg[i+1].len;
+ else if (read)
+ obuf[2] = msg[i].len;
else
obuf[2] = 0;
- memcpy(&obuf[3],msg[i].buf,msg[i].len);
+ memcpy(&obuf[3], msg[i].buf, msg[i].len);
if (ttusb2_msg(d, CMD_I2C_XFER, obuf, msg[i].len+3, ibuf, obuf[2] + 3) < 0) {
err("i2c transfer failed.");
break;
}
- if (read) {
- memcpy(msg[i+1].buf,&ibuf[3],msg[i+1].len);
+ if (write_read) {
+ memcpy(msg[i+1].buf, &ibuf[3], msg[i+1].len);
i++;
- }
+ } else if (read)
+ memcpy(msg[i].buf, &ibuf[3], msg[i].len);
}
mutex_unlock(&d->i2c_mutex);
@@ -190,6 +198,21 @@
.deltaf = 0xa511,
};
+static struct tda10048_config tda10048_config = {
+ .demod_address = 0x10 >> 1,
+ .output_mode = TDA10048_PARALLEL_OUTPUT,
+ .inversion = TDA10048_INVERSION_ON,
+ .dtv6_if_freq_khz = TDA10048_IF_4000,
+ .dtv7_if_freq_khz = TDA10048_IF_4500,
+ .dtv8_if_freq_khz = TDA10048_IF_5000,
+ .clk_freq_khz = TDA10048_CLK_16000,
+ .no_firmware = 1,
+};
+
+static struct tda827x_config tda827x_config = {
+ .config = 0,
+};
+
static int ttusb2_frontend_tda10086_attach(struct dvb_usb_adapter *adap)
{
if (usb_set_interface(adap->dev->udev,0,3) < 0)
@@ -203,23 +226,60 @@
return 0;
}
+static int ct3650_i2c_gate_ctrl(struct dvb_frontend* fe, int enable)
+{
+ struct dvb_usb_adapter *adap = fe->dvb->priv;
+
+ return adap->mfe[0]->ops.i2c_gate_ctrl(adap->mfe[0], enable);
+}
+
static int ttusb2_frontend_tda10023_attach(struct dvb_usb_adapter *adap)
{
if (usb_set_interface(adap->dev->udev, 0, 3) < 0)
err("set interface to alts=3 failed");
- if ((adap->fe = dvb_attach(tda10023_attach, &tda10023_config, &adap->dev->i2c_adap, 0x48)) == NULL) {
- deb_info("TDA10023 attach failed\n");
- return -ENODEV;
+
+ if (adap->mfe[0] == NULL) {
+ /* FE 0 DVB-C */
+ adap->mfe[0] = dvb_attach(tda10023_attach,
+ &tda10023_config, &adap->dev->i2c_adap, 0x48);
+
+ if (adap->mfe[0] == NULL) {
+ deb_info("TDA10023 attach failed\n");
+ return -ENODEV;
+ }
+ } else {
+ adap->mfe[1] = dvb_attach(tda10048_attach,
+ &tda10048_config, &adap->dev->i2c_adap);
+
+ if (adap->mfe[1] == NULL) {
+ deb_info("TDA10048 attach failed\n");
+ return -ENODEV;
+ }
+
+ /* tuner is behind TDA10023 I2C-gate */
+ adap->mfe[1]->ops.i2c_gate_ctrl = ct3650_i2c_gate_ctrl;
+
}
+
return 0;
}
static int ttusb2_tuner_tda827x_attach(struct dvb_usb_adapter *adap)
{
- if (dvb_attach(tda827x_attach, adap->fe, 0x61, &adap->dev->i2c_adap, NULL) == NULL) {
+ struct dvb_frontend *fe;
+
+ /* MFE: select correct FE to attach tuner since that's called twice */
+ if (adap->mfe[1] == NULL)
+ fe = adap->mfe[0];
+ else
+ fe = adap->mfe[1];
+
+ /* attach tuner */
+ if (dvb_attach(tda827x_attach, fe, 0x61, &adap->dev->i2c_adap, &tda827x_config) == NULL) {
printk(KERN_ERR "%s: No tda827x found!\n", __func__);
return -ENODEV;
}
+
return 0;
}
@@ -383,8 +443,7 @@
.num_adapters = 1,
.adapter = {
{
- .streaming_ctrl = NULL,
-
+ .num_frontends = 2,
.frontend_attach = ttusb2_frontend_tda10023_attach,
.tuner_attach = ttusb2_tuner_tda827x_attach,
diff -ur linux/drivers/media/dvb/frontends/tda10048.c linux.new/drivers/media/dvb/frontends/tda10048.c
--- linux/drivers/media/dvb/frontends/tda10048.c 2010-10-25 01:34:58.000000000 +0200
+++ linux.new/drivers/media/dvb/frontends/tda10048.c 2011-07-22 22:35:32.014271650 +0200
@@ -214,6 +214,8 @@
{ TDA10048_CLK_16000, TDA10048_IF_3800, 10, 3, 0 },
{ TDA10048_CLK_16000, TDA10048_IF_4000, 10, 3, 0 },
{ TDA10048_CLK_16000, TDA10048_IF_4300, 10, 3, 0 },
+ { TDA10048_CLK_16000, TDA10048_IF_4500, 5, 3, 0 },
+ { TDA10048_CLK_16000, TDA10048_IF_5000, 5, 3, 0 },
{ TDA10048_CLK_16000, TDA10048_IF_36130, 10, 3, 0 },
};
@@ -478,6 +480,11 @@
dprintk(1, "- pll_nfactor = %d\n", state->pll_nfactor);
dprintk(1, "- pll_pfactor = %d\n", state->pll_pfactor);
+ /* Set the pll registers */
+ tda10048_writereg(state, TDA10048_CONF_PLL1, 0x0f);
+ tda10048_writereg(state, TDA10048_CONF_PLL2, (u8)(state->pll_mfactor));
+ tda10048_writereg(state, TDA10048_CONF_PLL3, tda10048_readreg(state, TDA10048_CONF_PLL3) | ((u8)(state->pll_nfactor) | 0x40));
+
/* Calculate the sample frequency */
state->sample_freq = state->xtal_hz * (state->pll_mfactor + 45);
state->sample_freq /= (state->pll_nfactor + 1);
@@ -1123,7 +1130,7 @@
/* setup the state and clone the config */
memcpy(&state->config, config, sizeof(*config));
state->i2c = i2c;
- state->fwloaded = 0;
+ state->fwloaded = config->no_firmware;
state->bandwidth = BANDWIDTH_8_MHZ;
/* check if the demod is present */
diff -ur linux/drivers/media/dvb/frontends/tda10048.h linux.new/drivers/media/dvb/frontends/tda10048.h
--- linux/drivers/media/dvb/frontends/tda10048.h 2010-07-03 23:22:08.000000000 +0200
+++ linux.new/drivers/media/dvb/frontends/tda10048.h 2011-07-22 22:15:33.841271580 +0200
@@ -51,6 +51,7 @@
#define TDA10048_IF_4300 4300
#define TDA10048_IF_4500 4500
#define TDA10048_IF_4750 4750
+#define TDA10048_IF_5000 5000
#define TDA10048_IF_36130 36130
u16 dtv6_if_freq_khz;
u16 dtv7_if_freq_khz;
@@ -62,6 +63,8 @@
/* Disable I2C gate access */
u8 disable_gate_access;
+
+ bool no_firmware;
};
#if defined(CONFIG_DVB_TDA10048) || \
