Dark Shadow <shadowofdarkness@xxxxxxxxx> wrote: >I have a capture card that was sold as a Hauppauge HVR-1250 (according >to the box) that I am trying to use but I am having trouble getting >all it's features at once. When I leave it auto detected by the module >I have working TV in MythTV even though it thinks it is a 1270 but IR >isn't setup. > >dmesg outputs >#modprobe cx23885 enable_885_ir=1 >[ 7.592714] cx23885 driver version 0.0.2 loaded >[ 7.592748] cx23885 0000:07:00.0: PCI INT A -> GSI 17 (level, low) >-> IRQ 17 >[ 7.592926] CORE cx23885[0]: subsystem: 0070:2211, board: Hauppauge >WinTV-HVR1270 [card=18,autodetected] >[ 7.728163] IR JVC protocol handler initialized >[ 7.738971] tveeprom 0-0050: Hauppauge model 22111, rev C2F5, >serial# 6429897 >[ 7.738974] tveeprom 0-0050: MAC address is 00:0d:fe:62:1c:c9 >[ 7.738975] tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, >type 54) >[ 7.738977] tveeprom 0-0050: TV standards NTSC(M) ATSC/DVB Digital >(eeprom 0x88) >[ 7.738979] tveeprom 0-0050: audio processor is CX23888 (idx 40) >[ 7.738980] tveeprom 0-0050: decoder processor is CX23888 (idx 34) >[ 7.738982] tveeprom 0-0050: has no radio, has IR receiver, has no >IR transmitter >[ 7.738983] cx23885[0]: hauppauge eeprom: model=22111 >[ 7.738985] cx23885_dvb_register() allocating 1 frontend(s) >[ 7.738991] cx23885[0]: cx23885 based dvb card >[ 7.961122] IR Sony protocol handler initialized >[ 7.977301] tda18271 1-0060: creating new instance >[ 7.979325] TDA18271HD/C2 detected @ 1-0060 >[ 8.209663] DVB: registering new adapter (cx23885[0]) >[ 8.209668] DVB: registering adapter 0 frontend 0 (LG Electronics >LGDT3305 VSB/QAM Frontend)... >[ 8.210095] cx23885_dev_checkrevision() Hardware revision = 0xd0 >[ 8.210101] cx23885[0]/0: found at 0000:07:00.0, rev: 4, irq: 17, >latency: 0, mmio: 0xf7c00000 >[ 8.210109] cx23885 0000:07:00.0: setting latency timer to 64 >[ 8.210186] cx23885 0000:07:00.0: irq 49 for MSI/MSI-X > > >When I force it to be a 1250 no video works but IR seems to show up >(with the exception that it never seems to receive signals from the >remote) > >#modprobe cx23885 enable_885_ir=1 card=3 >[38647.660740] cx23885 driver version 0.0.2 loaded >[38647.660779] cx23885 0000:07:00.0: PCI INT A -> GSI 17 (level, low) >-> IRQ 17 >[38647.661009] CORE cx23885[0]: subsystem: 0070:2211, board: Hauppauge >WinTV-HVR1250 [card=3,insmod option] >[38647.787427] tveeprom 0-0050: Hauppauge model 22111, rev C2F5, >serial# 6429897 >[38647.787431] tveeprom 0-0050: MAC address is 00:0d:fe:62:1c:c9 >[38647.787434] tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, >type 54) >[38647.787437] tveeprom 0-0050: TV standards NTSC(M) ATSC/DVB Digital >(eeprom 0x88) >[38647.787439] tveeprom 0-0050: audio processor is CX23888 (idx 40) >[38647.787442] tveeprom 0-0050: decoder processor is CX23888 (idx 34) >[38647.787444] tveeprom 0-0050: has no radio, has IR receiver, has no >IR transmitter >[38647.787447] cx23885[0]: hauppauge eeprom: model=22111 >[38647.824508] cx25840 2-0044: cx23888 A/V decoder found @ 0x88 >(cx23885[0]) >[38648.457502] cx25840 2-0044: loaded v4l-cx23885-avcore-01.fw >firmware (16382 bytes) >[38648.465061] cx23885_dvb_register() allocating 1 frontend(s) >[38648.465064] cx23885[0]: cx23885 based dvb card >[38648.492632] cx23885[0]: frontend initialization failed >[38648.492637] cx23885_dvb_register() dvb_register failed err = -22 >[38648.492640] cx23885_dev_setup() Failed to register dvb on VID_C >[38648.492644] cx23885_dev_checkrevision() Hardware revision = 0xd0 >[38648.492650] cx23885[0]/0: found at 0000:07:00.0, rev: 4, irq: 17, >latency: 0, mmio: 0xf7c00000 >[38648.492660] cx23885 0000:07:00.0: setting latency timer to 64 >[38648.492740] cx23885 0000:07:00.0: irq 48 for MSI/MSI-X >[38648.539598] Registered IR keymap rc-hauppauge >[38648.539775] input: cx23885 IR (Hauppauge WinTV-HVR1250) as >/devices/pci0000:00/0000:00:1c.1/0000:07:00.0/rc/rc0/input4 >[38648.539852] rc0: cx23885 IR (Hauppauge WinTV-HVR1250) as >/devices/pci0000:00/0000:00:1c.1/0000:07:00.0/rc/rc0 >[38648.539926] rc rc0: lirc_dev: driver ir-lirc-codec (cx23885) >registered at minor = 0 > > >My setup commands for it's settings when using card=3 > >(I have read this is needed for this remote although according to the >Internet my grey remote is supposed to need a "hauppauge=1" parameter >but it doesn't exist (modinfo) in my version of the module from kernel >3.0-rc1 >#modprobe ir-kbd-i2c > >#ir-keytable -a /etc/rc_maps.cfg >Old keytable cleared >Wrote 136 keycode(s) to driver >Protocols changed to RC-5 > >#lsinput >/dev/input/event4 > bustype : BUS_PCI > vendor : 0x70 > product : 0x2211 > version : 1 > name : "cx23885 IR (Hauppauge WinTV-HVR1" > phys : "pci-0000:07:00.0/ir0" > bits ev : EV_SYN EV_KEY EV_MSC EV_REP > >#lspci -v (plus a little -n) >07:00.0 0400: 14f1:8880 (rev 04) > Subsystem: 0070:2211 > >07:00.0 Multimedia video controller: Conexant Systems, Inc. Hauppauge >Inc. HDPVR-1250 model 1196 (rev 04) > Subsystem: Hauppauge computer works Inc. Device 2211 > Flags: bus master, fast devsel, latency 0, IRQ 48 > Memory at f7c00000 (64-bit, non-prefetchable) [size=2M] > Capabilities: [40] Express Endpoint, MSI 00 > Capabilities: [80] Power Management version 3 > Capabilities: [90] Vital Product Data <?> > Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ >Queue=0/0 Enable+ > Capabilities: [100] Advanced Error Reporting <?> > Capabilities: [200] Virtual Channel <?> > Kernel driver in use: cx23885 > Kernel modules: cx23885 > > >I have heard this should show up as a normal keyboard to the system >but no button presses cause anything to happen to the system and >trying lirc with devinput (with devinput lircd.conf) and then opening >irw doesn't show any button presses either >-- >To unsubscribe from this list: send the line "unsubscribe linux-media" >in >the body of a message to majordomo@xxxxxxxxxxxxxxx >More majordomo info at http://vger.kernel.org/majordomo-info.html Don't force your card to a 1250, if the driver detects it is a 1270 with a CX23888 chip. No need to use the enable_885_ir parameter with a CX23888 chip, either. It only applies for two board models with actual CX23885 chips. Use of IR with the CX23888 chip should be realtively trouble free, *if* the 1270's IR has been enabled in the driver code. It likely has not been. I don't have the source code in front of me at the moment to check. It shouldn't be hard for anyone to patch a few files in the cx23885 driver to add it. Patches are welcome... Regards, Andy -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
