On Wed, 25 May 2011, achew@xxxxxxxxxx wrote:
> From: Andrew Chew <achew@xxxxxxxxxx>
>
> Based on vendor feedback, should issue a software reset at start of day.
>
> Also, OV9740_ANALOG_CTRL15 needs to be changed so the sensor does not begin
> streaming until it is ready (otherwise, results in a nonsense frame for the
> initial frame).
>
> For discontinuous clocks, need to change OV9740_MIPI_CTRL00.
>
> Finally, OV9740_ISP_CTRL19 needs to be changed to really use YUYV ordering
> (the previous value was for VYUY).
>
> Signed-off-by: Andrew Chew <achew@xxxxxxxxxx>
> ---
> drivers/media/video/ov9740.c | 10 +++++++++-
> 1 files changed, 9 insertions(+), 1 deletions(-)
>
> diff --git a/drivers/media/video/ov9740.c b/drivers/media/video/ov9740.c
> index d5c9061..9d7c74d 100644
> --- a/drivers/media/video/ov9740.c
> +++ b/drivers/media/video/ov9740.c
> @@ -68,6 +68,7 @@
> #define OV9740_ANALOG_CTRL04 0x3604
> #define OV9740_ANALOG_CTRL10 0x3610
> #define OV9740_ANALOG_CTRL12 0x3612
> +#define OV9740_ANALOG_CTRL15 0x3615
> #define OV9740_ANALOG_CTRL20 0x3620
> #define OV9740_ANALOG_CTRL21 0x3621
> #define OV9740_ANALOG_CTRL22 0x3622
> @@ -222,6 +223,9 @@ struct ov9740_priv {
> };
>
> static const struct ov9740_reg ov9740_defaults[] = {
> + /* Software Reset */
> + { OV9740_SOFTWARE_RESET, 0x01 },
> +
> /* Banding Filter */
> { OV9740_AEC_B50_STEP_HI, 0x00 },
> { OV9740_AEC_B50_STEP_LO, 0xe8 },
> @@ -333,6 +337,7 @@ static const struct ov9740_reg ov9740_defaults[] = {
> { OV9740_ANALOG_CTRL10, 0xa1 },
> { OV9740_ANALOG_CTRL12, 0x24 },
> { OV9740_ANALOG_CTRL22, 0x9f },
> + { OV9740_ANALOG_CTRL15, 0xf0 },
>
> /* Sensor Control */
> { OV9740_SENSOR_CTRL03, 0x42 },
> @@ -385,7 +390,7 @@ static const struct ov9740_reg ov9740_defaults[] = {
> { OV9740_LN_LENGTH_PCK_LO, 0x62 },
>
> /* MIPI Control */
> - { OV9740_MIPI_CTRL00, 0x44 },
> + { OV9740_MIPI_CTRL00, 0x64 }, /* 0x44 for continuous clock */
I think, the choice between continuous and discontinuous CSI-2 clock
should become configurable. You can only use discontinuous clock with
hosts, that support it, right? Whereas all hosts must support continuous
clock. So, I'm not sure we should unconditionally switch to discontinuous
clock here... Maybe it's better to keep it continuous until we make it
configurable?
> { OV9740_MIPI_3837, 0x01 },
> { OV9740_MIPI_CTRL01, 0x0f },
> { OV9740_MIPI_CTRL03, 0x05 },
> @@ -393,6 +398,9 @@ static const struct ov9740_reg ov9740_defaults[] = {
> { OV9740_VFIFO_RD_CTRL, 0x16 },
> { OV9740_MIPI_CTRL_3012, 0x70 },
> { OV9740_SC_CMMM_MIPI_CTR, 0x01 },
> +
> + /* YUYV order */
> + { OV9740_ISP_CTRL19, 0x02 },
> };
>
> static const struct ov9740_reg ov9740_regs_vga[] = {
> --
> 1.7.5.2
>
Thanks
Guennadi
---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
