Hello, I have a Terratec T5 USB DVB-T stick (similiar to TerraTec Cinergy DT USB XS Diversity). Receiving TV works like a charm on my OpenSUSE 11.4 (64 bit) machine. But I can't get the remote control to work. When I plug in the stick dmesg writes the following messages: [ 8870.704120] usb 2-1: new high speed USB device using ehci_hcd and address 2 [ 8870.819427] usb 2-1: New USB device found, idVendor=0ccd, idProduct=10a1 [ 8870.819436] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8870.819443] usb 2-1: Product: TerraTec T5 [ 8870.819448] usb 2-1: Manufacturer: TerraTec [ 8870.819452] usb 2-1: SerialNumber: 100802000436 [ 8870.820058] dvb-usb: found a 'Terratec Cinergy DT USB XS Diversity/ T5' in cold state, will try to load a firmware [ 8870.871809] dvb-usb: downloading firmware from file 'dvb-usb- dib0700-1.20.fw' [ 8871.073143] dib0700: firmware started successfully. [ 8871.574237] dvb-usb: found a 'Terratec Cinergy DT USB XS Diversity/ T5' in warm state. [ 8871.574358] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 8871.574476] DVB: registering new adapter (Terratec Cinergy DT USB XS Diversity/ T5) [ 8871.793130] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)... [ 8872.001597] DiB0070: successfully identified [ 8872.001605] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 8872.001673] DVB: registering new adapter (Terratec Cinergy DT USB XS Diversity/ T5) [ 8872.150711] DVB: registering adapter 1 frontend 0 (DiBcom 7000PC)... [ 8872.357432] DiB0070: successfully identified [ 8872.357447] Registered IR keymap rc-dib0700-rc5 [ 8872.357457] ir_create_table: Allocated space for 256 keycode entries (2048 bytes) [ 8872.357463] ir_setkeytable: Allocated space for 256 keycode entries (2048 bytes) [ 8872.357471] ir_update_mapping: #0: New scan 0x0700 with key 0x0071 [ 8872.357477] ir_update_mapping: #1: New scan 0x0701 with key 0x008b [ 8872.357482] ir_update_mapping: #2: New scan 0x0739 with key 0x0074 [ 8872.357488] ir_update_mapping: #2: New scan 0x0703 with key 0x0073 ... [ 8872.358606] ir_update_mapping: #83: New scan 0x1d37 with key 0x00a7 [ 8872.358613] ir_update_mapping: #84: New scan 0x1d3b with key 0x0162 [ 8872.358621] ir_update_mapping: #85: New scan 0x1d3d with key 0x0074 [ 8872.358867] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:13.2/usb2/2-1/rc/rc0/input9 [ 8872.358991] rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:13.2/usb2/2-1/rc/rc0 [ 8872.358999] __ir_input_register: Registered input device on dib0700 for rc- dib0700-rc5 remote. [ 8872.359371] dvb-usb: schedule remote query interval to 50 msecs. [ 8872.359380] dvb-usb: Terratec Cinergy DT USB XS Diversity/ T5 successfully initialized and connected. I followed the instruction from http://linuxtv.org/wiki/index.php/Remote_controllers-V4L but irrecord can't find the gap. When I tried a cat /dev/input/ir from time to time some strange symbols were put out on repeatedly pressing keys on the remote. I also tried to replace the firmware with the older version 1.10. But then the /dev/input/ir wont stop to fire event messages even if just one key was pressed. So I had a look at http://www.linuxtv.org/wiki/index.php/TerraTec_Cinergy_DT_USB_XS_Diversity and tried to change the protocol to NEC via the option dvb_usb_dib0700_ir_proto of the module dvb_usb_dib0700. But this option is no longer available. Where does it hide itself? Has someone an idea? Thanks in advance. Bye, Alexander -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
