Re: [alsa-devel] [PATCH v5] [resend] radio-sf16fmr2: convert to generic TEA575x interface

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



At Wed, 25 May 2011 21:21:30 -0300,
Mauro Carvalho Chehab wrote:
> 
> Em 23-05-2011 09:17, Ondrej Zary escreveu:
> > Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
> > driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
> > connected to ISA bus.
> > The card can optionally be equipped with PT2254A volume control (equivalent
> > of TC9154AP) - the volume setting is completely reworked (with balance control
> > added) and tested.
> 
> Ondrej,
> 
> As your first series went via alsa tree, and we are close to the end of the merge window,
> and assuming that Takashi didn't apply those patches on his tree, as you're re-sending it,
> I think that the better is to wait for the end of the merge window, in order to allow us
> to sync our development tree with 2.6.40-rc1, and then review and apply it on the top of it.

Yeah, I didn't pick it up as the patches are rather V4L-side changes
(although tea575x.c is in sound sub-directory).
And I agree with Mauro - let's merge it after rc1, so that we stand on
the same ground.  This sort of cross-tree change is better done at the
fixed point than in flux like during merge window.

That being said, I don't mind that Mauro or Hans applies these through
V4L tree.  In that case, you can take my acks for both patches.

Acked-by: Takashi Iwai <tiwai@xxxxxxx>

Of if it's preferred through sound tree, I can take them later.


thanks,

Takashi


> Thanks,
> Mauro.
> 
> > 
> > Signed-off-by: Ondrej Zary <linux@xxxxxxxxxxxxxxxxxxxx>
> > 
> > --- linux-2.6.39-rc2-/sound/pci/Kconfig	2011-05-15 18:50:18.000000000 +0200
> > +++ linux-2.6.39-rc2/sound/pci/Kconfig	2011-05-17 23:35:30.000000000 +0200
> > @@ -565,8 +565,8 @@ config SND_FM801_TEA575X_BOOL
> >  
> >  config SND_TEA575X
> >  	tristate
> > -	depends on SND_FM801_TEA575X_BOOL || SND_ES1968_RADIO
> > -	default SND_FM801 || SND_ES1968
> > +	depends on SND_FM801_TEA575X_BOOL || SND_ES1968_RADIO || RADIO_SF16FMR2
> > +	default SND_FM801 || SND_ES1968 || RADIO_SF16FMR2
> >  
> >  source "sound/pci/hda/Kconfig"
> >  
> > --- linux-2.6.39-rc2-/drivers/media/radio/radio-sf16fmr2.c	2011-04-06 03:30:43.000000000 +0200
> > +++ linux-2.6.39-rc2/drivers/media/radio/radio-sf16fmr2.c	2011-05-19 17:56:08.000000000 +0200
> > @@ -1,441 +1,209 @@
> > -/* SF16FMR2 radio driver for Linux radio support
> > - * heavily based on fmi driver...
> > - * (c) 2000-2002 Ziglio Frediano, freddy77@xxxxxxxxxxxxx
> > +/* SF16-FMR2 radio driver for Linux
> > + * Copyright (c) 2011 Ondrej Zary
> >   *
> > - * Notes on the hardware
> > - *
> > - *  Frequency control is done digitally -- ie out(port,encodefreq(95.8));
> > - *  No volume control - only mute/unmute - you have to use line volume
> > - *
> > - *  For read stereo/mono you must wait 0.1 sec after set frequency and
> > - *  card unmuted so I set frequency on unmute
> > - *  Signal handling seem to work only on autoscanning (not implemented)
> > - *
> > - *  Converted to V4L2 API by Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxx>
> > + * Original driver was (c) 2000-2002 Ziglio Frediano, freddy77@xxxxxxxxxxxxx
> > + * but almost nothing remained here after conversion to generic TEA575x
> > + * implementation
> >   */
> >  
> > +#include <linux/delay.h>
> >  #include <linux/module.h>	/* Modules 			*/
> >  #include <linux/init.h>		/* Initdata			*/
> >  #include <linux/ioport.h>	/* request_region		*/
> > -#include <linux/delay.h>	/* udelay			*/
> > -#include <linux/videodev2.h>	/* kernel radio structs		*/
> > -#include <linux/mutex.h>
> > -#include <linux/version.h>      /* for KERNEL_VERSION MACRO     */
> >  #include <linux/io.h>		/* outb, outb_p			*/
> > -#include <media/v4l2-device.h>
> > -#include <media/v4l2-ioctl.h>
> > +#include <sound/tea575x-tuner.h>
> >  
> > -MODULE_AUTHOR("Ziglio Frediano, freddy77@xxxxxxxxxxxxx");
> > -MODULE_DESCRIPTION("A driver for the SF16FMR2 radio.");
> > +MODULE_AUTHOR("Ondrej Zary");
> > +MODULE_DESCRIPTION("MediaForte SF16-FMR2 FM radio card driver");
> >  MODULE_LICENSE("GPL");
> >  
> > -static int io = 0x384;
> > -static int radio_nr = -1;
> > -
> > -module_param(io, int, 0);
> > -MODULE_PARM_DESC(io, "I/O address of the SF16FMR2 card (should be 0x384, if do not work try 0x284)");
> > -module_param(radio_nr, int, 0);
> > -
> > -#define RADIO_VERSION KERNEL_VERSION(0,0,2)
> > -
> > -#define AUD_VOL_INDEX 1
> > -
> > -#undef DEBUG
> > -//#define DEBUG 1
> > -
> > -#ifdef DEBUG
> > -# define  debug_print(s) printk s
> > -#else
> > -# define  debug_print(s)
> > -#endif
> > -
> > -/* this should be static vars for module size */
> > -struct fmr2
> > -{
> > -	struct v4l2_device v4l2_dev;
> > -	struct video_device vdev;
> > -	struct mutex lock;
> > +struct fmr2 {
> >  	int io;
> > -	int curvol; /* 0-15 */
> > -	int mute;
> > -	int stereo; /* card is producing stereo audio */
> > -	unsigned long curfreq; /* freq in kHz */
> > -	int card_type;
> > +	struct snd_tea575x tea;
> > +	struct v4l2_ctrl *volume;
> > +	struct v4l2_ctrl *balance;
> >  };
> >  
> > +/* the port is hardwired so no need to support multiple cards */
> > +#define FMR2_PORT	0x384
> >  static struct fmr2 fmr2_card;
> >  
> > -/* hw precision is 12.5 kHz
> > - * It is only useful to give freq in interval of 200 (=0.0125Mhz),
> > - * other bits will be truncated
> > - */
> > -#define RSF16_ENCODE(x)	((x) / 200 + 856)
> > -#define RSF16_MINFREQ (87 * 16000)
> > -#define RSF16_MAXFREQ (108 * 16000)
> > -
> > -static inline void wait(int n, int io)
> > -{
> > -	for (; n; --n)
> > -		inb(io);
> > -}
> > -
> > -static void outbits(int bits, unsigned int data, int nWait, int io)
> > -{
> > -	int bit;
> > -
> > -	for (; --bits >= 0;) {
> > -		bit = (data >> bits) & 1;
> > -		outb(bit, io);
> > -		wait(nWait, io);
> > -		outb(bit | 2, io);
> > -		wait(nWait, io);
> > -		outb(bit, io);
> > -		wait(nWait, io);
> > -	}
> > -}
> > -
> > -static inline void fmr2_mute(int io)
> > -{
> > -	outb(0x00, io);
> > -	wait(4, io);
> > -}
> > -
> > -static inline void fmr2_unmute(int io)
> > -{
> > -	outb(0x04, io);
> > -	wait(4, io);
> > -}
> > -
> > -static inline int fmr2_stereo_mode(int io)
> > -{
> > -	int n = inb(io);
> > -
> > -	outb(6, io);
> > -	inb(io);
> > -	n = ((n >> 3) & 1) ^ 1;
> > -	debug_print((KERN_DEBUG "stereo: %d\n", n));
> > -	return n;
> > -}
> > -
> > -static int fmr2_product_info(struct fmr2 *dev)
> > -{
> > -	int n = inb(dev->io);
> > -
> > -	n &= 0xC1;
> > -	if (n == 0) {
> > -		/* this should support volume set */
> > -		dev->card_type = 12;
> > -		return 0;
> > -	}
> > -	/* not volume (mine is 11) */
> > -	dev->card_type = (n == 128) ? 11 : 0;
> > -	return n;
> > -}
> > -
> > -static inline int fmr2_getsigstr(struct fmr2 *dev)
> > -{
> > -	/* !!! works only if scanning freq */
> > -	int res = 0xffff;
> > -
> > -	outb(5, dev->io);
> > -	wait(4, dev->io);
> > -	if (!(inb(dev->io) & 1))
> > -		res = 0;
> > -	debug_print((KERN_DEBUG "signal: %d\n", res));
> > -	return res;
> > -}
> > -
> > -/* set frequency and unmute card */
> > -static int fmr2_setfreq(struct fmr2 *dev)
> > -{
> > -	unsigned long freq = dev->curfreq;
> > -
> > -	fmr2_mute(dev->io);
> > -
> > -	/* 0x42 for mono output
> > -	 * 0x102 forward scanning
> > -	 * 0x182 scansione avanti
> > -	 */
> > -	outbits(9, 0x2, 3, dev->io);
> > -	outbits(16, RSF16_ENCODE(freq), 2, dev->io);
> > -
> > -	fmr2_unmute(dev->io);
> > -
> > -	/* wait 0.11 sec */
> > -	msleep(110);
> > -
> > -	/* NOTE if mute this stop radio
> > -	   you must set freq on unmute */
> > -	dev->stereo = fmr2_stereo_mode(dev->io);
> > -	return 0;
> > -}
> > -
> > -/* !!! not tested, in my card this does't work !!! */
> > -static int fmr2_setvolume(struct fmr2 *dev)
> > -{
> > -	int vol[16] = { 0x021, 0x084, 0x090, 0x104,
> > -			0x110, 0x204, 0x210, 0x402,
> > -			0x404, 0x408, 0x410, 0x801,
> > -			0x802, 0x804, 0x808, 0x810 };
> > -	int i, a;
> > -	int n = vol[dev->curvol & 0x0f];
> > -
> > -	if (dev->card_type != 11)
> > -		return 1;
> > -
> > -	for (i = 12; --i >= 0; ) {
> > -		a = ((n >> i) & 1) << 6; /* if (a==0) a = 0; else a = 0x40; */
> > -		outb(a | 4, dev->io);
> > -		wait(4, dev->io);
> > -		outb(a | 0x24, dev->io);
> > -		wait(4, dev->io);
> > -		outb(a | 4, dev->io);
> > -		wait(4, dev->io);
> > -	}
> > -	for (i = 6; --i >= 0; ) {
> > -		a = ((0x18 >> i) & 1) << 6;
> > -		outb(a | 4, dev->io);
> > -		wait(4, dev->io);
> > -		outb(a | 0x24, dev->io);
> > -		wait(4, dev->io);
> > -		outb(a | 4, dev->io);
> > -		wait(4, dev->io);
> > -	}
> > -	wait(4, dev->io);
> > -	outb(0x14, dev->io);
> > -	return 0;
> > -}
> > -
> > -static int vidioc_querycap(struct file *file, void  *priv,
> > -					struct v4l2_capability *v)
> > -{
> > -	strlcpy(v->driver, "radio-sf16fmr2", sizeof(v->driver));
> > -	strlcpy(v->card, "SF16-FMR2 radio", sizeof(v->card));
> > -	strlcpy(v->bus_info, "ISA", sizeof(v->bus_info));
> > -	v->version = RADIO_VERSION;
> > -	v->capabilities = V4L2_CAP_TUNER | V4L2_CAP_RADIO;
> > -	return 0;
> > -}
> > +/* TEA575x tuner pins */
> > +#define STR_DATA	(1 << 0)
> > +#define STR_CLK		(1 << 1)
> > +#define STR_WREN	(1 << 2)
> > +#define STR_MOST	(1 << 3)
> > +/* PT2254A/TC9154A volume control pins */
> > +#define PT_ST		(1 << 4)
> > +#define PT_CK		(1 << 5)
> > +#define PT_DATA		(1 << 6)
> > +/* volume control presence pin */
> > +#define FMR2_HASVOL	(1 << 7)
> >  
> > -static int vidioc_g_tuner(struct file *file, void *priv,
> > -					struct v4l2_tuner *v)
> > +static void fmr2_tea575x_set_pins(struct snd_tea575x *tea, u8 pins)
> >  {
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > -
> > -	if (v->index > 0)
> > -		return -EINVAL;
> > +	struct fmr2 *fmr2 = tea->private_data;
> > +	u8 bits = 0;
> >  
> > -	strlcpy(v->name, "FM", sizeof(v->name));
> > -	v->type = V4L2_TUNER_RADIO;
> > -
> > -	v->rangelow = RSF16_MINFREQ;
> > -	v->rangehigh = RSF16_MAXFREQ;
> > -	v->rxsubchans = fmr2->stereo ? V4L2_TUNER_SUB_STEREO :
> > -					V4L2_TUNER_SUB_MONO;
> > -	v->capability = V4L2_TUNER_CAP_STEREO | V4L2_TUNER_CAP_LOW;
> > -	v->audmode = V4L2_TUNER_MODE_STEREO;
> > -	mutex_lock(&fmr2->lock);
> > -	v->signal = fmr2_getsigstr(fmr2);
> > -	mutex_unlock(&fmr2->lock);
> > -	return 0;
> > -}
> > +	bits |= (pins & TEA575X_DATA) ? STR_DATA : 0;
> > +	bits |= (pins & TEA575X_CLK)  ? STR_CLK  : 0;
> > +	/* WRITE_ENABLE is inverted, DATA must be high during read */
> > +	bits |= (pins & TEA575X_WREN) ? 0 : STR_WREN | STR_DATA;
> >  
> > -static int vidioc_s_tuner(struct file *file, void *priv,
> > -					struct v4l2_tuner *v)
> > -{
> > -	return v->index ? -EINVAL : 0;
> > +	outb(bits, fmr2->io);
> >  }
> >  
> > -static int vidioc_s_frequency(struct file *file, void *priv,
> > -					struct v4l2_frequency *f)
> > +static u8 fmr2_tea575x_get_pins(struct snd_tea575x *tea)
> >  {
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > +	struct fmr2 *fmr2 = tea->private_data;
> > +	u8 bits = inb(fmr2->io);
> >  
> > -	if (f->tuner != 0 || f->type != V4L2_TUNER_RADIO)
> > -		return -EINVAL;
> > -	if (f->frequency < RSF16_MINFREQ ||
> > -			f->frequency > RSF16_MAXFREQ)
> > -		return -EINVAL;
> > -	/* rounding in steps of 200 to match the freq
> > -	   that will be used */
> > -	fmr2->curfreq = (f->frequency / 200) * 200;
> > -
> > -	/* set card freq (if not muted) */
> > -	if (fmr2->curvol && !fmr2->mute) {
> > -		mutex_lock(&fmr2->lock);
> > -		fmr2_setfreq(fmr2);
> > -		mutex_unlock(&fmr2->lock);
> > -	}
> > -	return 0;
> > +	return  (bits & STR_DATA) ? TEA575X_DATA : 0 |
> > +		(bits & STR_MOST) ? TEA575X_MOST : 0;
> >  }
> >  
> > -static int vidioc_g_frequency(struct file *file, void *priv,
> > -					struct v4l2_frequency *f)
> > +static void fmr2_tea575x_set_direction(struct snd_tea575x *tea, bool output)
> >  {
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > -
> > -	if (f->tuner != 0)
> > -		return -EINVAL;
> > -	f->type = V4L2_TUNER_RADIO;
> > -	f->frequency = fmr2->curfreq;
> > -	return 0;
> >  }
> >  
> > -static int vidioc_queryctrl(struct file *file, void *priv,
> > -					struct v4l2_queryctrl *qc)
> > -{
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > +static struct snd_tea575x_ops fmr2_tea_ops = {
> > +	.set_pins = fmr2_tea575x_set_pins,
> > +	.get_pins = fmr2_tea575x_get_pins,
> > +	.set_direction = fmr2_tea575x_set_direction,
> > +};
> >  
> > -	switch (qc->id) {
> > -	case V4L2_CID_AUDIO_MUTE:
> > -		return v4l2_ctrl_query_fill(qc, 0, 1, 1, 1);
> > -	case V4L2_CID_AUDIO_VOLUME:
> > -		/* Only card_type == 11 implements volume */
> > -		if (fmr2->card_type == 11)
> > -			return v4l2_ctrl_query_fill(qc, 0, 15, 1, 0);
> > -		return v4l2_ctrl_query_fill(qc, 0, 1, 1, 0);
> > -	}
> > -	return -EINVAL;
> > -}
> > +/* TC9154A/PT2254A volume control */
> >  
> > -static int vidioc_g_ctrl(struct file *file, void *priv,
> > -					struct v4l2_control *ctrl)
> > -{
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > +/* 18-bit shift register bit definitions */
> > +#define TC9154A_ATT_MAJ_0DB	(1 << 0)
> > +#define TC9154A_ATT_MAJ_10DB	(1 << 1)
> > +#define TC9154A_ATT_MAJ_20DB	(1 << 2)
> > +#define TC9154A_ATT_MAJ_30DB	(1 << 3)
> > +#define TC9154A_ATT_MAJ_40DB	(1 << 4)
> > +#define TC9154A_ATT_MAJ_50DB	(1 << 5)
> > +#define TC9154A_ATT_MAJ_60DB	(1 << 6)
> > +
> > +#define TC9154A_ATT_MIN_0DB	(1 << 7)
> > +#define TC9154A_ATT_MIN_2DB	(1 << 8)
> > +#define TC9154A_ATT_MIN_4DB	(1 << 9)
> > +#define TC9154A_ATT_MIN_6DB	(1 << 10)
> > +#define TC9154A_ATT_MIN_8DB	(1 << 11)
> > +/* bit 12 is ignored */
> > +#define TC9154A_CHANNEL_LEFT	(1 << 13)
> > +#define TC9154A_CHANNEL_RIGHT	(1 << 14)
> > +/* bits 15, 16, 17 must be 0 */
> > +
> > +#define	TC9154A_ATT_MAJ(x)	(1 << x)
> > +#define TC9154A_ATT_MIN(x)	(1 << (7 + x))
> > +
> > +static void tc9154a_set_pins(struct fmr2 *fmr2, u8 pins)
> > +{
> > +	if (!fmr2->tea.mute)
> > +		pins |= STR_WREN;
> > +
> > +	outb(pins, fmr2->io);
> > +}
> > +
> > +static void tc9154a_set_attenuation(struct fmr2 *fmr2, int att, u32 channel)
> > +{
> > +	int i;
> > +	u32 reg;
> > +	u8 bit;
> > +
> > +	reg = TC9154A_ATT_MAJ(att / 10) | TC9154A_ATT_MIN((att % 10) / 2);
> > +	reg |= channel;
> > +	/* write 18-bit shift register, LSB first */
> > +	for (i = 0; i < 18; i++) {
> > +		bit = reg & (1 << i) ? PT_DATA : 0;
> > +		tc9154a_set_pins(fmr2, bit);
> > +		udelay(5);
> > +		tc9154a_set_pins(fmr2, bit | PT_CK);
> > +		udelay(5);
> > +		tc9154a_set_pins(fmr2, bit);
> > +	}
> > +
> > +	/* latch register data */
> > +	udelay(5);
> > +	tc9154a_set_pins(fmr2, PT_ST);
> > +	udelay(5);
> > +	tc9154a_set_pins(fmr2, 0);
> > +}
> > +
> > +static int fmr2_s_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > +	struct snd_tea575x *tea = container_of(ctrl->handler, struct snd_tea575x, ctrl_handler);
> > +	struct fmr2 *fmr2 = tea->private_data;
> > +	int volume, balance, left, right;
> >  
> >  	switch (ctrl->id) {
> > -	case V4L2_CID_AUDIO_MUTE:
> > -		ctrl->value = fmr2->mute;
> > -		return 0;
> >  	case V4L2_CID_AUDIO_VOLUME:
> > -		ctrl->value = fmr2->curvol;
> > -		return 0;
> > -	}
> > -	return -EINVAL;
> > -}
> > -
> > -static int vidioc_s_ctrl(struct file *file, void *priv,
> > -					struct v4l2_control *ctrl)
> > -{
> > -	struct fmr2 *fmr2 = video_drvdata(file);
> > -
> > -	switch (ctrl->id) {
> > -	case V4L2_CID_AUDIO_MUTE:
> > -		fmr2->mute = ctrl->value;
> > +		volume = ctrl->val;
> > +		balance = fmr2->balance->cur.val;
> >  		break;
> > -	case V4L2_CID_AUDIO_VOLUME:
> > -		fmr2->curvol = ctrl->value;
> > +	case V4L2_CID_AUDIO_BALANCE:
> > +		balance = ctrl->val;
> > +		volume = fmr2->volume->cur.val;
> >  		break;
> >  	default:
> >  		return -EINVAL;
> >  	}
> >  
> > -#ifdef DEBUG
> > -	if (fmr2->curvol && !fmr2->mute)
> > -		printk(KERN_DEBUG "unmute\n");
> > -	else
> > -		printk(KERN_DEBUG "mute\n");
> > -#endif
> > -
> > -	mutex_lock(&fmr2->lock);
> > -	if (fmr2->curvol && !fmr2->mute) {
> > -		fmr2_setvolume(fmr2);
> > -		/* Set frequency and unmute card */
> > -		fmr2_setfreq(fmr2);
> > -	} else
> > -		fmr2_mute(fmr2->io);
> > -	mutex_unlock(&fmr2->lock);
> > -	return 0;
> > -}
> > +	left = right = volume;
> > +	if (balance < 0)
> > +		right = max(0, right + balance);
> > +	if (balance > 0)
> > +		left = max(0, left - balance);
> >  
> > -static int vidioc_g_input(struct file *filp, void *priv, unsigned int *i)
> > -{
> > -	*i = 0;
> > -	return 0;
> > -}
> > -
> > -static int vidioc_s_input(struct file *filp, void *priv, unsigned int i)
> > -{
> > -	return i ? -EINVAL : 0;
> > -}
> > +	tc9154a_set_attenuation(fmr2, abs(left - 68), TC9154A_CHANNEL_LEFT);
> > +	tc9154a_set_attenuation(fmr2, abs(right - 68), TC9154A_CHANNEL_RIGHT);
> >  
> > -static int vidioc_g_audio(struct file *file, void *priv,
> > -					struct v4l2_audio *a)
> > -{
> > -	a->index = 0;
> > -	strlcpy(a->name, "Radio", sizeof(a->name));
> > -	a->capability = V4L2_AUDCAP_STEREO;
> >  	return 0;
> >  }
> >  
> > -static int vidioc_s_audio(struct file *file, void *priv,
> > -					struct v4l2_audio *a)
> > +static const struct v4l2_ctrl_ops fmr2_ctrl_ops = {
> > +	.s_ctrl = fmr2_s_ctrl,
> > +};
> > +
> > +static int fmr2_tea_ext_init(struct snd_tea575x *tea)
> >  {
> > -	return a->index ? -EINVAL : 0;
> > -}
> > +	struct fmr2 *fmr2 = tea->private_data;
> >  
> > -static const struct v4l2_file_operations fmr2_fops = {
> > -	.owner          = THIS_MODULE,
> > -	.unlocked_ioctl = video_ioctl2,
> > -};
> > +	if (inb(fmr2->io) & FMR2_HASVOL) {
> > +		fmr2->volume = v4l2_ctrl_new_std(&tea->ctrl_handler, &fmr2_ctrl_ops, V4L2_CID_AUDIO_VOLUME, 0, 68, 2, 56);
> > +		fmr2->balance = v4l2_ctrl_new_std(&tea->ctrl_handler, &fmr2_ctrl_ops, V4L2_CID_AUDIO_BALANCE, -68, 68, 2, 0);
> > +		if (tea->ctrl_handler.error) {
> > +			printk(KERN_ERR "radio-sf16fmr2: can't initialize controls\n");
> > +			return tea->ctrl_handler.error;
> > +		}
> > +	}
> >  
> > -static const struct v4l2_ioctl_ops fmr2_ioctl_ops = {
> > -	.vidioc_querycap    = vidioc_querycap,
> > -	.vidioc_g_tuner     = vidioc_g_tuner,
> > -	.vidioc_s_tuner     = vidioc_s_tuner,
> > -	.vidioc_g_audio     = vidioc_g_audio,
> > -	.vidioc_s_audio     = vidioc_s_audio,
> > -	.vidioc_g_input     = vidioc_g_input,
> > -	.vidioc_s_input     = vidioc_s_input,
> > -	.vidioc_g_frequency = vidioc_g_frequency,
> > -	.vidioc_s_frequency = vidioc_s_frequency,
> > -	.vidioc_queryctrl   = vidioc_queryctrl,
> > -	.vidioc_g_ctrl      = vidioc_g_ctrl,
> > -	.vidioc_s_ctrl      = vidioc_s_ctrl,
> > -};
> > +	return 0;
> > +}
> >  
> >  static int __init fmr2_init(void)
> >  {
> >  	struct fmr2 *fmr2 = &fmr2_card;
> > -	struct v4l2_device *v4l2_dev = &fmr2->v4l2_dev;
> > -	int res;
> >  
> > -	strlcpy(v4l2_dev->name, "sf16fmr2", sizeof(v4l2_dev->name));
> > -	fmr2->io = io;
> > -	fmr2->stereo = 1;
> > -	mutex_init(&fmr2->lock);
> > +	fmr2->io = FMR2_PORT;
> >  
> > -	if (!request_region(fmr2->io, 2, "sf16fmr2")) {
> > -		v4l2_err(v4l2_dev, "request_region failed!\n");
> > +	if (!request_region(fmr2->io, 2, "SF16-FMR2")) {
> > +		printk(KERN_ERR "radio-sf16fmr2: I/O port 0x%x already in use\n", fmr2->io);
> >  		return -EBUSY;
> >  	}
> >  
> > -	res = v4l2_device_register(NULL, v4l2_dev);
> > -	if (res < 0) {
> > -		release_region(fmr2->io, 2);
> > -		v4l2_err(v4l2_dev, "Could not register v4l2_device\n");
> > -		return res;
> > -	}
> > -
> > -	strlcpy(fmr2->vdev.name, v4l2_dev->name, sizeof(fmr2->vdev.name));
> > -	fmr2->vdev.v4l2_dev = v4l2_dev;
> > -	fmr2->vdev.fops = &fmr2_fops;
> > -	fmr2->vdev.ioctl_ops = &fmr2_ioctl_ops;
> > -	fmr2->vdev.release = video_device_release_empty;
> > -	video_set_drvdata(&fmr2->vdev, fmr2);
> > -
> > -	/* mute card - prevents noisy bootups */
> > -	fmr2_mute(fmr2->io);
> > -	fmr2_product_info(fmr2);
> > +	fmr2->tea.private_data = fmr2;
> > +	fmr2->tea.ops = &fmr2_tea_ops;
> > +	fmr2->tea.ext_init = fmr2_tea_ext_init;
> > +	strlcpy(fmr2->tea.card, "SF16-FMR2", sizeof(fmr2->tea.card));
> > +	strcpy(fmr2->tea.bus_info, "ISA");
> >  
> > -	if (video_register_device(&fmr2->vdev, VFL_TYPE_RADIO, radio_nr) < 0) {
> > -		v4l2_device_unregister(v4l2_dev);
> > +	if (snd_tea575x_init(&fmr2->tea)) {
> > +		printk(KERN_ERR "radio-sf16fmr2: Unable to detect TEA575x tuner\n");
> >  		release_region(fmr2->io, 2);
> > -		return -EINVAL;
> > +		return -ENODEV;
> >  	}
> >  
> > -	v4l2_info(v4l2_dev, "SF16FMR2 radio card driver at 0x%x.\n", fmr2->io);
> > -	debug_print((KERN_DEBUG "card_type %d\n", fmr2->card_type));
> > +	printk(KERN_INFO "radio-sf16fmr2: SF16-FMR2 radio card at 0x%x.\n", fmr2->io);
> >  	return 0;
> >  }
> >  
> > @@ -443,22 +211,9 @@ static void __exit fmr2_exit(void)
> >  {
> >  	struct fmr2 *fmr2 = &fmr2_card;
> >  
> > -	video_unregister_device(&fmr2->vdev);
> > -	v4l2_device_unregister(&fmr2->v4l2_dev);
> > +	snd_tea575x_exit(&fmr2->tea);
> >  	release_region(fmr2->io, 2);
> >  }
> >  
> >  module_init(fmr2_init);
> >  module_exit(fmr2_exit);
> > -
> > -#ifndef MODULE
> > -
> > -static int __init fmr2_setup_io(char *str)
> > -{
> > -	get_option(&str, &io);
> > -	return 1;
> > -}
> > -
> > -__setup("sf16fmr2=", fmr2_setup_io);
> > -
> > -#endif
> > 
> > 
> 
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel@xxxxxxxxxxxxxxxx
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux