On 22 May 2011 15:49, Igor Grinberg <grinberg@xxxxxxxxxxxxxx> wrote:
> Hi Javier,
>
>
> linux-omap should be CC'ed - added.
>
> In addition to Koen's comments, some comments below.
>
>
> On 05/20/11 16:47, Javier Martin wrote:
>
>> isp.h file has to be included as a temporal measure
>> since clocks of the isp are not exposed yet.
>>
>> Signed-off-by: Javier Martin <javier.martin@xxxxxxxxxxxxxxxxx>
>> ---
>> arch/arm/mach-omap2/board-omap3beagle.c | 127 ++++++++++++++++++++++++++++++-
>> 1 files changed, 123 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
>> index 33007fd..f52e6ae 100644
>> --- a/arch/arm/mach-omap2/board-omap3beagle.c
>> +++ b/arch/arm/mach-omap2/board-omap3beagle.c
>> @@ -24,15 +24,20 @@
>> #include <linux/input.h>
>> #include <linux/gpio_keys.h>
>> #include <linux/opp.h>
>> +#include <linux/i2c.h>
>> +#include <linux/mm.h>
>> +#include <linux/videodev2.h>
>>
>> #include <linux/mtd/mtd.h>
>> #include <linux/mtd/partitions.h>
>> #include <linux/mtd/nand.h>
>> #include <linux/mmc/host.h>
>> -
>> +#include <linux/gpio.h>
>
> Why include this for second time?
Good catch, I'll fix it.
[snip]
>> @@ -309,6 +357,15 @@ static int beagle_twl_gpio_setup(struct device *dev,
>> pr_err("%s: unable to configure EHCI_nOC\n", __func__);
>> }
>>
>> + if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
>> + /*
>> + * Power on camera interface - only on pre-production, not
>> + * needed on production boards
>> + */
>> + gpio_request(gpio + 2, "CAM_EN");
>> + gpio_direction_output(gpio + 2, 1);
>
> Why not gpio_request_one()?
Just to follow the same approach as in the rest of the code.
Maybe a further patch could change all "gpio_request()" uses to
"gpio_request_one()".
>
>> + }
>> +
>> /*
>> * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
>> * high / others active low)
>> @@ -451,6 +508,8 @@ static struct twl4030_platform_data beagle_twldata = {
>> .vsim = &beagle_vsim,
>> .vdac = &beagle_vdac,
>> .vpll2 = &beagle_vpll2,
>> + .vaux3 = &beagle_vaux3,
>> + .vaux4 = &beagle_vaux4,
>> };
>>
>> static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
>> @@ -463,15 +522,16 @@ static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
>> };
>>
>> static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
>> - {
>> - I2C_BOARD_INFO("eeprom", 0x50),
>> - },
>> + {
>> + I2C_BOARD_INFO("eeprom", 0x50),
>> + },
>> };
>
> This part of the hunk is not related to the patch
> and should be in a separate (cleanup) patch.
>
Sure, I'll fix it.
>>
>> static int __init omap3_beagle_i2c_init(void)
>> {
>> omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
>> ARRAY_SIZE(beagle_i2c_boardinfo));
>> + omap_register_i2c_bus(2, 100, NULL, 0); /* Enable I2C2 for camera */
>> /* Bus 3 is attached to the DVI port where devices like the pico DLP
>> * projector don't work reliably with 400kHz */
>> omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
>> @@ -654,6 +714,60 @@ static void __init beagle_opp_init(void)
>> return;
>> }
>>
>> +static int beagle_cam_set_xclk(struct v4l2_subdev *subdev, int hz)
>> +{
>> + struct isp_device *isp = v4l2_dev_to_isp_device(subdev->v4l2_dev);
>> + int ret;
>> +
>> + ret = isp->platform_cb.set_xclk(isp, hz, MT9P031_XCLK);
>> + return 0;
>> +}
>
> Why do you need ret variable here, if you always return zero?
>
You are right, it's not needed any longer.
>> +
>> +static int beagle_cam_reset(struct v4l2_subdev *subdev, int active)
>> +{
>> + /* Set RESET_BAR to !active */
>> + gpio_set_value(MT9P031_RESET_GPIO, !active);
>> +
>> + return 0;
>> +}
>> +
>> +static struct mt9p031_platform_data beagle_mt9p031_platform_data = {
>> + .set_xclk = beagle_cam_set_xclk,
>> + .reset = beagle_cam_reset,
>> +};
>> +
>> +static struct i2c_board_info mt9p031_camera_i2c_device = {
>> + I2C_BOARD_INFO("mt9p031", 0x48),
>> + .platform_data = &beagle_mt9p031_platform_data,
>> +};
>> +
>> +static struct isp_subdev_i2c_board_info mt9p031_camera_subdevs[] = {
>> + {
>> + .board_info = &mt9p031_camera_i2c_device,
>> + .i2c_adapter_id = 2,
>> + },
>> + { NULL, 0, },
>> +};
>> +
>> +static struct isp_v4l2_subdevs_group beagle_camera_subdevs[] = {
>> + {
>> + .subdevs = mt9p031_camera_subdevs,
>> + .interface = ISP_INTERFACE_PARALLEL,
>> + .bus = {
>> + .parallel = {
>> + .data_lane_shift = 0,
>> + .clk_pol = 1,
>> + .bridge = ISPCTRL_PAR_BRIDGE_DISABLE,
>> + }
>> + },
>> + },
>> + { },
>> +};
>> +
>> +static struct isp_platform_data beagle_isp_platform_data = {
>> + .subdevs = beagle_camera_subdevs,
>> +};
>> +
>> static void __init omap3_beagle_init(void)
>> {
>> omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
>> @@ -679,6 +793,11 @@ static void __init omap3_beagle_init(void)
>>
>> beagle_display_init();
>> beagle_opp_init();
>> +
>> + /* Enable camera */
>> + gpio_request(MT9P031_RESET_GPIO, "cam_rst");
>> + gpio_direction_output(MT9P031_RESET_GPIO, 0);
>
> gpio_request_one()?
ditto
>> + omap3_init_camera(&beagle_isp_platform_data);
>> }
>>
>> MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
>
>
>
> --
> Regards,
> Igor.
>
>
--
Javier Martin
Vista Silicon S.L.
CDTUC - FASE C - Oficina S-345
Avda de los Castros s/n
39005- Santander. Cantabria. Spain
+34 942 25 32 60
www.vista-silicon.com
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
