last, but not least, that i totally forgot - on my tests with audio card PEX 8111/8112 adapter is stuttering to transfer 8 channel, 192 kHz, 24-bit audio, which is very small data rate comparing to DVB data - i'm not sure though, it's because of increased latency or PEX 8111/8112 adapter can't handle huge data rate for some other reason. On Tue, Feb 15, 2011 at 10:20 AM, Konstantin Dimitrov <kosio.dimitrov@xxxxxxxxx> wrote: > oh, i have just noticed your DVB card is for Cable and not for > Satellite, but still it may use 12V PCI interface pins for something > else and not exactly for LNB power as i thought assuming it's DVB-S/S2 > DVB card. > > On Tue, Feb 15, 2011 at 10:18 AM, Konstantin Dimitrov > <kosio.dimitrov@xxxxxxxxx> wrote: >> hi, does your DVB card can get signal lock when it's inserted into the >> PCI-to-PCIE adapter, because as far as i know most PCI-to-PCIE >> adapters based on PEX 8111/8112 don't provide power to 12V pins of the >> PCI interface, which probably all PCI DVB card use for LNB power. so, >> what i would check if i'm at your position is the LNB power of the >> card as well as if there is no some extensive amount of noise in the >> LNB power when the DVB card is inside PEX 8111/8112 PCI-to-PCIE >> adapter. also, i can give you example from my own experience with an >> "Audiotrak Prodigy HD2" PCI audio card and PEX 8111/8112 based >> PCI-to-PCIE adapters - with one such adapter that don't provide power >> to 12V pins of the PCI interface there is no sound coming out, because >> the amplifier on the card uses power from 12V pins of the PCI >> interface, with another PEX 8111/8112 PCI-to-PCIE adapter that seems >> to provide power to 12V pins there is extensive noise in the sound >> that is coming out, because PCI-to-PCIE adapter doesn't provide good >> power on 12V pins of the PCI interface and thus the noise in the >> audio. also, on some motherboards (with nVidia chipset on my tests) >> there was some problem with how the memory was mapped preventing the >> work of the PCI card when it's inserted into PEX 8111/8112 based >> PCI-to-PCIE adapter. so, it's also helpful to test motherboards with >> different chipset. in any case it's always better to find and use >> native PCI-Express card instead of PEX 8111/8112 PCI-to-PCIE adapter >> and PCI card. anyway, maybe, someone with more hardware engineering >> knowledge then i have, especially if the problem is 12V can find some >> way to fix those cheap PEX 8111/8112 PCI-to-PCIE adapters that are >> floating around, because i'm sure they just sacrifice 12V power to >> lower the BOM cost of the adapter. BTW, i'm sure your firewire card is >> working, because it doesn't use 12V PCI interface pins - it's the same >> with many PCI cards, but all that needs 12V are no-go based on my >> experience. >> >> --konstantin >> >> On Mon, Feb 14, 2011 at 1:35 PM, Dennis Kurten <dennis.kurten@xxxxxxxxx> wrote: >>> Hello, >>> >>> This card (technisat cablestar hd 2 dvb-c) works fine when plugged >>> into a native PCI slot. >>> When I try it with a PCI-adapter I intend to use in mITX-builds there >>> doesn't seem >>> to be any data coming in through the tuner. The adapter is a >>> transparent bridge (with a >>> PEX 8112 chip) that goes into a 1xPCIe-slot and gets power through a >>> 4-pin molex. >>> >>> My guess is some kind of dma mapping incompatibility with the mantis >>> driver (s2-liplianin). >>> The card seems to initialize correctly, but doesn't work when the >>> tuner is put into action >>> (scandvb timeouts, dvbtraffic yields nothing). For the record, I've >>> tested the bridge with a >>> firewire card and that works fine. >>> >>> Kernel is 2.6.32 (+the compiled drivers) >>> >>> lspci for the bridge and the card: >>> -------------------------------------- >>> 03:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI >>> Express-to-PCI Bridge (rev aa) (prog-if 00 [Normal decode]) >>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >>> ParErr- Stepping- SERR- FastB2B- DisINTx- >>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- >>> <TAbort- <MAbort- >SERR- <PERR- INTx- >>> Latency: 0, Cache Line Size: 32 bytes >>> Bus: primary=03, secondary=04, subordinate=04, sec-latency=32 >>> I/O behind bridge: 0000e000-0000efff >>> Memory behind bridge: fdd00000-fddfffff >>> Prefetchable memory behind bridge: fdc00000-fdcfffff >>> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >>>>TAbort- <TAbort- <MAbort- <SERR- <PERR- >>> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- >>> PriDiscTmr- SecDiscTmr- DiscTmrStat+ DiscTmrSERREn- >>> Capabilities: <access denied> >>> Kernel modules: shpchp >>> >>> 04:00.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV >>> PCI Bridge Controller [Ver 1.0] (rev 01) >>> Subsystem: Device 1ae4:0002 >>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >>> ParErr- Stepping- SERR- FastB2B- DisINTx- >>> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >>>>TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx- >>> Latency: 32 (2000ns min, 63750ns max) >>> Interrupt: pin A routed to IRQ 16 >>> Region 0: Memory at fdcff000 (32-bit, prefetchable) [size=4K] >>> Kernel driver in use: Mantis >>> Kernel modules: mantis >>> >>> dmesg output with modules loaded: >>> ----------------------------------------- >>> Mantis 0000:04:00.0: PCI INT A -> Link[APC7] -> GSI 16 (level, low) -> IRQ 16 >>> irq: 16, latency: 32 >>> memory: 0xfdcff000, mmio: 0xffffc900031a0000 >>> found a VP-2040 PCI DVB-C device on (04:00.0), >>> Mantis Rev 1 [1ae4:0002], irq: 16, latency: 32 >>> memory: 0xfdcff000, mmio: 0xffffc900031a0000 >>> MAC Address=[00:08:c9:d0:46:b4] >>> mantis_alloc_buffers (0): DMA=0x1bb90000 cpu=0xffff88001bb90000 size=65536 >>> mantis_alloc_buffers (0): RISC=0x1bbec000 cpu=0xffff88001bbec000 size=1000 >>> DVB: registering new adapter (Mantis dvb adapter) >>> mantis_frontend_init (0): Probing for CU1216 (DVB-C) >>> TDA10023: i2c-addr = 0x0c, id = 0x7d >>> mantis_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10023) @ 0x0c >>> mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success >>> DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)... >>> mantis_ca_init (0): Registering EN50221 device >>> mantis_ca_init (0): Registered EN50221 device >>> mantis_hif_init (0): Adapter(0) Initializing Mantis Host Interface >>> Registered IR keymap rc-vp2040 >>> input: Mantis VP-2040 IR Receiver as /devices/virtual/rc/rc4/input11 >>> rc4: Mantis VP-2040 IR Receiver as /devices/virtual/rc/rc4 >>> b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded >>> successfully >>> >>> >>> I hear sometimes these bridges are not as transparent as they claim, >>> any pointers on what to look for? >>> >>> Regards, >>> Dennis >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-media" in >>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> >> > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
