Apologies for bumping this message, but I am still having this problem. I thought that this Hauppauge receiver should work flawlessly ... Any clue's? On Mon, Dec 27, 2010 at 1:47 PM, Ray Kinsella <raykinsella78@xxxxxxxxx> wrote: > Hi all, > > I recently purchased a Hauppauge Nova-T USB DVB-T receiver and have > been having trouble getting it to work. > I read through the Wiki page > (http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-NOVA-T-Stick) > for this device and followed the instructions but still no luck. > > Most of the time the frontend will fail to attach (as show below), on > the rare occasions when the frontend does attach it will hang when I > try to scan for channels. > In both cases the driver complains of I2C read/write failures. > I am using the latest from code from the V4L-DVB backports repository > with a 2.6.35 Kernel (Mythubuntu 10.10) > > Any advice on what to try? > > ray@pvr:~$ uname -a > Linux pvr 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:34:50 UTC > 2010 i686 GNU/Linux > > ray@pvr:~$ lsusb > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > ... > Bus 001 Device 004: ID 2040:7070 Hauppauge Nova-T Stick 3 > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > > ray@pvr:~$ dmesg > [ 18.492014] usb 1-4: new high speed USB device using ehci_hcd and address 4 > [ 18.653158] WARNING: You're using an experimental version of the > DVB stack. As the driver > [ 18.653160] is backported to an older kernel, it doesn't > offer enough quality for > [ 18.653161] its usage in production. > [ 18.653161] Use it with care. > [ 18.667402] dib0700: loaded with support for 14 different device-types > [ 18.667425] check for cold 10b8 1e14 > [ 18.667426] check for cold 10b8 1e78 > [ 18.667427] check for cold 2040 7050 > [ 18.667428] check for cold 2040 7060 > [ 18.667430] check for cold 7ca a807 > [ 18.667431] check for cold 7ca b808 > [ 18.667432] check for cold 185b 1e78 > [ 18.667433] check for cold 185b 1e80 > [ 18.667434] check for cold 1584 6003 > [ 18.667436] check for cold 413 6f00 > [ 18.667437] check for cold 413 6f01 > [ 18.667438] check for cold 7ca b568 > [ 18.667439] check for cold 1044 7001 > [ 18.667440] check for cold 2040 9941 > [ 18.667441] check for cold 2040 9950 > [ 18.667443] check for cold 2304 22c > [ 18.667444] check for cold ccd 5a > [ 18.667445] check for cold 2040 9580 > [ 18.667446] check for cold 10b8 1ef0 > [ 18.667447] check for cold 1164 1e8c > [ 18.667448] check for cold b05 171f > [ 18.667450] check for cold 1164 1edc > [ 18.667451] check for cold ccd 62 > [ 18.667452] check for cold 10b8 1ebc > [ 18.667453] check for cold 2304 228 > [ 18.667454] check for cold 5d8 810f > [ 18.667456] check for cold b05 173f > [ 18.667457] check for cold 2040 7070 > [ 18.667565] FW GET_VERSION length: -32 > [ 18.667567] cold: 1 > [ 18.667568] dvb-usb: found a 'Hauppauge Nova-T Stick' in cold > state, will try to load a firmware > [ 18.674300] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw' > [ 18.875965] dib0700: firmware started successfully. > [ 24.376079] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state. > [ 24.376086] power control: 1 > [ 24.376129] dvb-usb: will pass the complete MPEG2 transport stream > to the software demuxer. > [ 24.376546] DVB: registering new adapter (Hauppauge Nova-T Stick) > [ 74.424074] ep 0 read error (status = -110) > [ 74.424079] I2C read failed on address 0x40 > [ 84.424148] ep 0 read error (status = -110) > [ 84.424151] I2C read failed on address 0x09 > [ 84.424157] dib0700: stk7070p_frontend_attach: > dib7000p_i2c_enumeration failed. Cannot continue > [ 84.424159] > [ 84.424162] dvb-usb: no frontend was attached by 'Hauppauge Nova-T Stick' > [ 84.424166] power control: 0 > [ 84.424168] dvb-usb: Hauppauge Nova-T Stick successfully > initialized and connected. > [ 89.424093] Firmware version: 0, -1941421839, 0x1000000, 1348026105 > [ 94.424065] dib0700: ir protocol setup failed > [ 94.424104] usbcore: registered new interface driver dvb_usb_dib0700 > > > ray@pvr:~$ cat /etc/modprobe.d/options.conf > options dvb_usb_dib0700 force_lna_activation=1 debug=1 > options dvb_usb disable_rc_polling=1 debug=1 > options dvb_core debug=1 > > ray@pvr:~$ lsmod > Module Size Used by > dvb_usb_dib0700 56317 0 > dib7000p 16176 1 dvb_usb_dib0700 > dib0090 13333 1 dvb_usb_dib0700 > dib7000m 13132 1 dvb_usb_dib0700 > dib0070 7766 1 dvb_usb_dib0700 > dvb_usb 17643 1 dvb_usb_dib0700 > dib8000 25510 1 dvb_usb_dib0700 > dvb_core 86744 3 dib7000p,dvb_usb,dib8000 > dib3000mc 11200 1 dvb_usb_dib0700 > dibx000_common 3112 4 dib7000p,dib7000m,dib8000,dib3000mc > usbhid 36882 0 > hid 67742 1 usbhid > ... > > Thanks > > Ray Kinsella > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
