Hi guys, I am trying to get working my Hauppauge WinTV 1400 expresscard. Actually, i've got using the 2.6.36-gentoo-r5 kernel (gentoo-sources). First, I've enabled all necessary module (cx23885). After inserting the card, i get this messages: pciehp 0000:00:1c.3:pcie04: Card present on Slot(3) pci 0000:05:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit] pci 0000:05:00.0: supports D1 D2 pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot pci 0000:05:00.0: PME# disabled pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:05:00.0: BAR 0: assigned [mem 0xf0000000-0xf01fffff 64bit] pci 0000:05:00.0: BAR 0: set to [mem 0xf0000000-0xf01fffff 64bit] (PCI address [0xf0000000-0xf01fffff] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c] pcieport 0000:00:1c.3: bridge window [io 0x2000-0x2fff] pcieport 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff] pcieport 0000:00:1c.3: bridge window [mem 0xf2900000-0xf29fffff 64bit pref] pcieport 0000:00:1c.3: setting latency timer to 64 pci 0000:05:00.0: no hotplug settings from platform cx23885 0000:05:00.0: enabling device (0000 -> 0002) cx23885 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 CORE cx23885[1]: subsystem: 0070:8010, board: Hauppauge WinTV-HVR1400 [card=9,autodetected] tveeprom 8-0050: Hauppauge model 80019, rev B2F1, serial# 3757209 tveeprom 8-0050: MAC address is 00:0d:fe:39:54:99 tveeprom 8-0050: tuner model is Xceive XC3028L (idx 151, type 4) tveeprom 8-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 8-0050: audio processor is CX23885 (idx 39) tveeprom 8-0050: decoder processor is CX23885 (idx 33) tveeprom 8-0050: has radio cx23885[1]: hauppauge eeprom: model=80019 cx23885_dvb_register() allocating 1 frontend(s) cx23885[1]: cx23885 based dvb card xc2028 9-0064: creating new instance xc2028 9-0064: type set to XCeive xc2028/xc3028 tuner DVB: registering new adapter (cx23885[1]) DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[1]/0: found at 0000:05:00.0, rev: 2, irq: 19, latency: 0, mmio: 0xf0000000 cx23885 0000:05:00.0: setting latency timer to 64 cx23885 0000:05:00.0: irq 48 for MSI/MSI-X So, as you can see, the card is found and the driver is loaded. So, when I now try to start the tuning, it will fail. For example, I try to scan for the dvb-t channels: dvbscan /usr/share/dvb/dvb-t/de-Niedersachsen This command will fail, it says tuning failed. DMESG says now: xc2028 9-0064: Loading 81 firmware images from xc3028L-v36.fw, type: xc2028 firmware, ver 3.6 xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware xc2028 9-0064: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 9-0064: i2c output error: rc = -6 (should be 64) xc2028 9-0064: -6 returned from send xc2028 9-0064: Error -22 while loading base firmware The firmware could be loaded. Any ideas, how this could be fixed? -- Gruà ConiKost -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
