From: Jai Luthra <jai.luthra@xxxxxxxxxxxxxxxx>
For DS90UB9702-Q1, it is recommended to configure some serializer
settings over the back-channel before the forward-channel is active.
This can only be done if the serializer's I2C address on the FPD-Link
bus is populated in the device tree node.
Signed-off-by: Jai Luthra <jai.luthra@xxxxxxxxxxxxxxxx>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx>
---
drivers/media/i2c/ds90ub960.c | 124 ++++++++++++++++++++++++++++++++++++++++--
1 file changed, 120 insertions(+), 4 deletions(-)
diff --git a/drivers/media/i2c/ds90ub960.c b/drivers/media/i2c/ds90ub960.c
index a534d077f045..1ec3c060d4c6 100644
--- a/drivers/media/i2c/ds90ub960.c
+++ b/drivers/media/i2c/ds90ub960.c
@@ -248,13 +248,16 @@ MODULE_PARM_DESC(enable_sscg, "Enable SSCG (if available)");
#define UB960_RR_BCC_CONFIG 0x58
#define UB960_RR_BCC_CONFIG_BC_ALWAYS_ON BIT(4)
+#define UB960_RR_BCC_CONFIG_AUTO_ACK_ALL BIT(5)
#define UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH BIT(6)
#define UB960_RR_BCC_CONFIG_BC_FREQ_SEL_MASK GENMASK(2, 0)
#define UB960_RR_DATAPATH_CTL1 0x59
#define UB960_RR_DATAPATH_CTL2 0x5a
#define UB960_RR_SER_ID 0x5b
+#define UB960_RR_SER_ID_FREEZE_DEVICE_ID BIT(0)
#define UB960_RR_SER_ALIAS_ID 0x5c
+#define UB960_RR_SER_ALIAS_ID_AUTO_ACK BIT(0)
/* For these two register sets: n < UB960_MAX_PORT_ALIASES */
#define UB960_RR_SLAVE_ID(n) (0x5d + (n))
@@ -507,7 +510,9 @@ struct ub960_rxport {
struct fwnode_handle *fwnode;
struct i2c_client *client;
unsigned short alias; /* I2C alias (lower 7 bits) */
+ short addr; /* Local I2C address (lower 7 bits) */
struct ds90ub9xx_platform_data pdata;
+ struct regmap *regmap;
} ser;
enum ub960_rxport_mode rx_mode;
@@ -2005,6 +2010,78 @@ static unsigned long ub960_calc_bc_clk_rate_ub9702(struct ub960_data *priv,
}
}
+static int ub960_rxport_serializer_write(struct ub960_rxport *rxport, u8 reg,
+ u8 val, int *err)
+{
+ struct ub960_data *priv = rxport->priv;
+ struct device *dev = &priv->client->dev;
+ union i2c_smbus_data data;
+ int ret;
+
+ if (err && *err)
+ return *err;
+
+ data.byte = val;
+
+ ret = i2c_smbus_xfer(priv->client->adapter, rxport->ser.alias, 0,
+ I2C_SMBUS_WRITE, reg, I2C_SMBUS_BYTE_DATA, &data);
+ if (ret)
+ dev_err(dev,
+ "rx%u: cannot write serializer register 0x%02x (%d)!\n",
+ rxport->nport, reg, ret);
+
+ if (ret && err)
+ *err = ret;
+
+ return ret;
+}
+
+static int ub960_rxport_bc_ser_config(struct ub960_rxport *rxport)
+{
+ struct ub960_data *priv = rxport->priv;
+ struct device *dev = &priv->client->dev;
+ u8 nport = rxport->nport;
+ int ret;
+
+ /* Skip port if serializer's address is not known */
+ if (rxport->ser.addr < 0) {
+ dev_dbg(dev,
+ "rx%u: 'i2c-addr' property missing, skip serializer configuration\n",
+ nport);
+ return 0;
+ }
+
+ /*
+ * Note: the code here probably only works for CSI-2 serializers in
+ * sync mode. To support other serializers the BC related configuration
+ * should be done before calling this function.
+ */
+
+ /* Enable I2C passthrough and auto-ack on BC */
+ ub960_rxport_update_bits(priv, nport, UB960_RR_BCC_CONFIG,
+ UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH |
+ UB960_RR_BCC_CONFIG_AUTO_ACK_ALL,
+ UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH |
+ UB960_RR_BCC_CONFIG_AUTO_ACK_ALL,
+ &ret);
+
+ if (ret)
+ return ret;
+
+ /* Disable BC alternate mode auto detect */
+ ub960_rxport_serializer_write(rxport, 0x4b, 0x02, &ret);
+ /* Decrease link detect timer */
+ ub960_rxport_serializer_write(rxport, 0x49, 0x06, &ret);
+
+ /* Disable I2C passthrough and auto-ack on BC */
+ ub960_rxport_update_bits(priv, nport, UB960_RR_BCC_CONFIG,
+ UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH |
+ UB960_RR_BCC_CONFIG_AUTO_ACK_ALL,
+ 0x0, &ret);
+
+ return ret;
+}
+
static int ub960_rxport_add_serializer(struct ub960_data *priv, u8 nport)
{
struct ub960_rxport *rxport = priv->rxports[nport];
@@ -2956,6 +3033,36 @@ static int ub960_init_rx_ports_ub9702(struct ub960_data *priv)
if (ret)
return ret;
+ for_each_active_rxport(priv) {
+ if (it.rxport->ser.addr >= 0) {
+ /*
+ * Set serializer's I2C address if set in the dts file,
+ * and freeze it to prevent updates from the FC.
+ */
+ ub960_rxport_write(priv, it.nport, UB960_RR_SER_ID,
+ it.rxport->ser.addr << 1 |
+ UB960_RR_SER_ID_FREEZE_DEVICE_ID,
+ &ret);
+ }
+
+ /* Set serializer I2C alias with auto-ack */
+ ub960_rxport_write(priv, it.nport, UB960_RR_SER_ALIAS_ID,
+ it.rxport->ser.alias << 1 |
+ UB960_RR_SER_ALIAS_ID_AUTO_ACK, &ret);
+
+ if (ret)
+ return ret;
+ }
+
+ for_each_active_rxport(priv) {
+ if (fwnode_device_is_compatible(it.rxport->ser.fwnode,
+ "ti,ds90ub971-q1")) {
+ ret = ub960_rxport_bc_ser_config(it.rxport);
+ if (ret)
+ return ret;
+ }
+ }
+
if (ub960_enable_sscg) {
ret = ub960_enable_sscg_ub9702(priv);
if (ret)
@@ -3090,16 +3197,17 @@ static int ub960_init_rx_ports_ub9702(struct ub960_data *priv)
ub960_rxport_write(priv, it.nport, UB960_RR_PORT_ICR_LO, 0x7f,
&ret);
+ /* Clear serializer I2C alias auto-ack */
+ ub960_rxport_update_bits(priv, it.nport, UB960_RR_SER_ALIAS_ID,
+ UB960_RR_SER_ALIAS_ID_AUTO_ACK, 0,
+ &ret);
+
/* Enable I2C_PASS_THROUGH */
ub960_rxport_update_bits(priv, it.nport, UB960_RR_BCC_CONFIG,
UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH,
UB960_RR_BCC_CONFIG_I2C_PASS_THROUGH,
&ret);
- /* Enable I2C communication to the serializer via the alias */
- ub960_rxport_write(priv, it.nport, UB960_RR_SER_ALIAS_ID,
- it.rxport->ser.alias << 1, &ret);
-
if (ret)
return ret;
}
@@ -4258,6 +4366,7 @@ ub960_parse_dt_rxport_link_properties(struct ub960_data *priv,
s32 strobe_pos;
u32 eq_level;
u32 ser_i2c_alias;
+ u32 ser_i2c_addr;
int ret;
cdr_mode = RXPORT_CDR_FPD3;
@@ -4363,6 +4472,13 @@ ub960_parse_dt_rxport_link_properties(struct ub960_data *priv,
}
rxport->ser.alias = ser_i2c_alias;
+ ret = fwnode_property_read_u32(link_fwnode, "i2c-addr",
+ &ser_i2c_addr);
+ if (ret)
+ rxport->ser.addr = -EINVAL;
+ else
+ rxport->ser.addr = ser_i2c_addr;
+
rxport->ser.fwnode = fwnode_get_named_child_node(link_fwnode, "serializer");
if (!rxport->ser.fwnode) {
dev_err(dev, "rx%u: missing 'serializer' node\n", nport);
--
2.43.0
