Add error handling for i2c reads/writes in various places. Reported-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx> Link: https://lore.kernel.org/all/Zv40EQSR__JDN_0M@kekkonen.localdomain/ Reviewed-by: Jai Luthra <jai.luthra@xxxxxxxxxxxxxxxx> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx> --- drivers/media/i2c/ds90ub953.c | 46 ++++++++++++++++++++++++++++++------------- 1 file changed, 32 insertions(+), 14 deletions(-) diff --git a/drivers/media/i2c/ds90ub953.c b/drivers/media/i2c/ds90ub953.c index b6451811f906..f8f3e31f0077 100644 --- a/drivers/media/i2c/ds90ub953.c +++ b/drivers/media/i2c/ds90ub953.c @@ -401,8 +401,13 @@ static int ub953_gpiochip_probe(struct ub953_data *priv) int ret; /* Set all GPIOs to local input mode */ - ub953_write(priv, UB953_REG_LOCAL_GPIO_DATA, 0); - ub953_write(priv, UB953_REG_GPIO_INPUT_CTRL, 0xf); + ret = ub953_write(priv, UB953_REG_LOCAL_GPIO_DATA, 0); + if (ret) + return ret; + + ret = ub953_write(priv, UB953_REG_GPIO_INPUT_CTRL, 0xf); + if (ret) + return ret; gc->label = dev_name(dev); gc->parent = dev; @@ -970,10 +975,11 @@ static void ub953_calc_clkout_params(struct ub953_data *priv, clkout_data->rate = clkout_rate; } -static void ub953_write_clkout_regs(struct ub953_data *priv, - const struct ub953_clkout_data *clkout_data) +static int ub953_write_clkout_regs(struct ub953_data *priv, + const struct ub953_clkout_data *clkout_data) { u8 clkout_ctrl0, clkout_ctrl1; + int ret; if (priv->hw_data->is_ub971) clkout_ctrl0 = clkout_data->m; @@ -983,8 +989,15 @@ static void ub953_write_clkout_regs(struct ub953_data *priv, clkout_ctrl1 = clkout_data->n; - ub953_write(priv, UB953_REG_CLKOUT_CTRL0, clkout_ctrl0); - ub953_write(priv, UB953_REG_CLKOUT_CTRL1, clkout_ctrl1); + ret = ub953_write(priv, UB953_REG_CLKOUT_CTRL0, clkout_ctrl0); + if (ret) + return ret; + + ret = ub953_write(priv, UB953_REG_CLKOUT_CTRL1, clkout_ctrl1); + if (ret) + return ret; + + return 0; } static unsigned long ub953_clkout_recalc_rate(struct clk_hw *hw, @@ -1064,9 +1077,7 @@ static int ub953_clkout_set_rate(struct clk_hw *hw, unsigned long rate, dev_dbg(&priv->client->dev, "%s %lu (requested %lu)\n", __func__, clkout_data.rate, rate); - ub953_write_clkout_regs(priv, &clkout_data); - - return 0; + return ub953_write_clkout_regs(priv, &clkout_data); } static const struct clk_ops ub953_clkout_ops = { @@ -1091,7 +1102,9 @@ static int ub953_register_clkout(struct ub953_data *priv) /* Initialize clkout to 25MHz by default */ ub953_calc_clkout_params(priv, UB953_DEFAULT_CLKOUT_RATE, &clkout_data); - ub953_write_clkout_regs(priv, &clkout_data); + ret = ub953_write_clkout_regs(priv, &clkout_data); + if (ret) + return ret; priv->clkout_clk_hw.init = &init; @@ -1238,10 +1251,15 @@ static int ub953_hw_init(struct ub953_data *priv) if (ret) return dev_err_probe(dev, ret, "i2c init failed\n"); - ub953_write(priv, UB953_REG_GENERAL_CFG, - (priv->non_continous_clk ? 0 : UB953_REG_GENERAL_CFG_CONT_CLK) | - ((priv->num_data_lanes - 1) << UB953_REG_GENERAL_CFG_CSI_LANE_SEL_SHIFT) | - UB953_REG_GENERAL_CFG_CRC_TX_GEN_ENABLE); + v = 0; + v |= priv->non_continous_clk ? 0 : UB953_REG_GENERAL_CFG_CONT_CLK; + v |= (priv->num_data_lanes - 1) << + UB953_REG_GENERAL_CFG_CSI_LANE_SEL_SHIFT; + v |= UB953_REG_GENERAL_CFG_CRC_TX_GEN_ENABLE; + + ret = ub953_write(priv, UB953_REG_GENERAL_CFG, v); + if (ret) + return ret; return 0; } -- 2.43.0
